>From an earlier post...
>One more time...
>1) download and use the latest version of POSER (3.0a5)
>2) make sure the "Redirect NetLib Calls to Host TCP/IP" in Properties is
>checked. and "Use TCP/IP Sockets" is checked in CodeWarrior
>3) Make sure the app you are about to debug is not running on POSER, also
>its a good idea to make sure POSER is in the Preferences or launcher app.
>4) Do NOT have Constructor running when you attempt to debug. The 100% CPU
>usage bug crept back.
-----Original Message-----
From: Palm <[EMAIL PROTECTED]>
Newsgroups: palm-dev-forum
To: Palm Developer Forum <[EMAIL PROTECTED]>
Date: Tuesday, April 11, 2000 10:37 AM
Subject: Re: Frist App, where(what) is BDWM?
>OK, I'm having this same problem. I have CW Lite I'm at the same point in
>the tutorial.
>
>First, is there anywhere in the documentation where these 'shortcuts' are
>described?
>When I press F5 in CW, I then start Find on the Palm and enter the
'shortcut
>.. 2'.
>It beeps and clears the line. When I press Enter in CW, Hotsync launches
>automatically
>on th ePalm and I get the BDWM message in CW. I did a soft reset on the
>Palm and
>managed to get the app to download once, but then Hotsync launches and I'm
>still unable
>to debug it from within CW. Is there anyway to disable HotSync completely?
>
>Is there some documentation that would be helpful (and accurate) that might
>answer some
>these type of questions. So far, I'm very dissappointed at the inaccuracy
>of the docs that
>came with the CW Lite installation. I see several on the Palm site but
with
>very limited
>knowledge of Palm and CW, I'm not sure where to begin. Any help would be
>greatly
>appreciated.
>
>Keith
>
>"Jun-Kiat Lam" <[EMAIL PROTECTED]> wrote in message
>news:7359@palm-dev-forum...
>>
>> BTW the message bug has been fixed in the latest linker plugin, which is
>> part of the Palm OS 3.5 SDK. If you download and install it, it will plug
>> right into your CW installation.
>>
>> In this case it sounds like the 'shortcut dot dot 2' wasn't recognized
>> correctly by the device, or the serial port is somehow busy. Make sure
>that
>> Hotsync is completely off, make sure that the serial port of the device
is
>> free (a soft reset will fix that), and try entering the 'shortcut dot dot
>2'
>> in the Find dialog. If entered correctly the line will disappear, and
>there
>> should be no up-arrow at the lower right. Also you may want to check that
>> the debugger is actually targeting the correct COM port (in the Palm
>> Connection Settings).
>>
>> Hope this helps.
>>
>> Rgds,
>> Jun-Kiat Lam
>> Metrowerks Technical Support
>>
>> ----- Original Message -----
>> From: "Nick Torenvliet" <[EMAIL PROTECTED]>
>> To: "Palm Developer Forum" <[EMAIL PROTECTED]>
>> Sent: Thursday, April 06, 2000 11:47 AM
>> Subject: Frist App, where(what) is BDWM?
>>
>>
>> >
>> > I am trying to debug my first palm app(see Palm OS tutorial pg. 37)
>> >
>> > I've pretty much followed the entire procedure(I think) I've gotten
>> console
>> > mode up etc.
>> >
>> > When I click OK to confrim console mode to the debugger I get the
>> following
>> > message:
>> >
>> > The de-bug helper app could not be found
>> > The registry key 'BDWM' is not defined
>> >
>> > What do I need to do to get around this?
>> >
>> >
>> >
>> > --
>> > For information on using the Palm Developer Forums, or to unsubscribe,
>> please see http://www.palm.com/devzone/mailinglists.html
>> >
>>
>>
>>
>
>
>
>--
>For information on using the Palm Developer Forums, or to unsubscribe,
please see http://www.palm.com/devzone/mailinglists.html
>
>
--
For information on using the Palm Developer Forums, or to unsubscribe, please see
http://www.palm.com/devzone/mailinglists.html
