Jim,

I can't remember the year, but I think '96-'98 would cover the period.

The amount of water that went around the inlet and injectors would have 
shown the air leak on the injector seals.  We didn't take the injectors out, 
just swapped over the entire rail.

All the other inlet seals were sealed up with blue sealant, then we realised 
the petrol would eat that, so we disassembled and re-assembled with red 
sealant.  We were not convinced the gaskets alone would work, hence the 
sealant.

It sounds like we got the breathers correct then.  the 2 round the back of 
the alloy inlet have been blocked off and the other goes to the breather on 
the front of the engine, partially behind the exhaust manifold.  Not sure 
about a 1-way valve on this though - is this something that needs to be 
added, or is this part of the canister that's behind the exhaust?
The main breather in the rocket cover is just vented to atmosphere, via a 
pipe the dips low and a mini air filter.

There was no charcoal canister on the engine - at least not that I remember, 
but the wiring was there for the sensor, which I assume is normal?
Other than the LAMBDA Idon't thing there is any other emission control.

Regards,
Steve
--
www.h4-turbo.co.uk
www.quantumowners.co.uk
www.quantumcars.co.uk
www.quantumheritage.co.uk

On Monday 07 Jun 2010, Jim Hearne wrote:
> Hmm,
> Mostly sounds ok.
> 
> The rev counter output from the ecu is generated internally so the only
> fault making the rev counter not work but the engine still run must be
> between the ecu and the rev counter and wouldn't affect anything else.
> 
> If the loom has the OBD2 connector and it's from a 1996 ish car which i
> think it was then it's almost certainly the same as my Mondeo.
> Ford switched to the OBD2 connector but kept there own signals on it
> which means you can't use any sort of OBD2 diagnostic.
> It still has to be a Ford specific diagnostic tool.
> I did try making an adaptor from the old Ford diags connector to the
> OBD2 but it didn't work.
> 
> A decent auto electrician should have diagnostics that will work but it
> may just report no faults like my Mondeo did.
> 
> The engine should stall if you unplug the idle spec valve, this may be a
> clue to the fault, still an air leak somewhat.
> The idle working with the air bypassing the MAF may also be a clue but
> in my mind this should make the problem worse if theres an air leak.
> 
> I have in the past had problems with air leaks around the injector seals.
> 
> Ah, a thought, when you swapped the fuel rail from the Plastic manifold
> to the metal one, did you change the seals on the injectors, they are
> different sizes.
> You could have an air leak on all 4 injectors !
> 
> The only other though i have mentioned before, putting the plastic inlet
> manifold throttle body on the metal manifold needs the metal manifolds
> gasket, the other one causes a problem with the idle air path (this goes
> through the throttle body) but i forget exactly what.
> 
> I seem to also remember the plastic inlet manifold gasket won't work on
> the metal inlet manifold,
> 
> I presume the various vacumn pipe connections on the throttle body are
> connected or blanked off (2 i think) and the breather on the end of
> inlet manifold under the coil pack is correctly connected round to the
> breather on the front of the engine with the one way valve working ok.
> 
> What has been done with the Charcol canister pipework and any other
> emissions systems.
> 
> Jim
> 
> On 07/06/2010 13:59, Steve Kodz wrote:
> > OK, here it goes:
> > 
> > MAF - we have cleaned the connections and checked that the connections
> > look good.  I was able to get a good idle by disconnecting the MAF
> > unit from the inlet pipe and changing how much of the area of the MAF
> > was flowing into the inlet - ie bleeding extra air into the engine
> > that the MAF wasn't measuring.
> > 
> > Geoff - can you remember if I shortened the MAF wiring, in case there
> > is a poor joint causing the issue?  You might need to check the loom
> > if you can't remember.
> > 
> > Power Steering Switch - we had wiring for this, which when bridged
> > reduced the idle by 100rpm, so I've cut the connector off and soldered
> > the wires together.  A small step in the right direction, but this is
> > not the fault.
> > 
> > TPS (Throttle pot) - I forgot to test the ranges and output, but I was
> > able to swap the original one with one from an RS1800i inlet and this
> > made no difference.
> > 
> > ISCV - This was taken off and cleaned with WD40.  We also applied
> > varied volts and amps to watch the action, which all appears to be OK.
> > 
> > Wiring Loom - we used the donor loom.
> > 
> > Air Temperature Sesnor/CAM Sensor - We removed the ATS from the plastic
> > inlet, as it had a different connector to the one on the alloy inlet,
> > but had the same thread.  I believe this means we have the connectors
> > on the correct way round.  The CAM Sensor uses the same style
> > connector as the injectors, but is keyed differently, where the ATS is
> > a different style.
> > 
> > Road Speed Sensor - Disconnecting the road speed sensor didn't appear
> > to make any difference.
> > 
> > LAMBDA - Again disconnecting didn't appear to make any difference.
> > 
> > One thing to note is when Geoff arrived he mentioned that the rev
> > counter started flickering about, then died completely.  When I
> > checked the connection I found that it all looked OK and even got an
> > rpm reading on a multimeter that matched the engine speed.  Then the
> > rev counter started working again, but if I connected the multimeter
> > it would stop - almost like there is a weak signal.  Could this be
> > related?
> > 
> > The hose pipe was used (and Carole didn't even get wet!) to test the
> > engine for air leaks and none were found.  The whole area around the
> > inlet was given a good soaking, but the engine still idled too high.
> > 
> > Geoff - it could be worth removing the inlet hose to check the throttle
> > butterfly is closing completely, but I'm guessing it will be.
> > 
> > I think this is almost driving me as mad as it is Geoff - thanks to all
> > for the suggestions.
> > 
> > Does anyone know a source for good ODB2 readers and software, as if I'm
> > going to do more work with Zetecs and other modern engine management
> > systems this could be a good investment.
> > 
> > Regards,
> > Steve
> > --
> > www.h4-turbo.co.uk
> > www.quantumowners.co.uk
> > www.quantumcars.co.uk
> > www.quantumheritage.co.uk
> > 
> > On Monday 07 Jun 2010, Andy Heaton wrote:
> >> Geoff.
> >> 
> >> After breaking down on the M25 with your car the other Friday Eve. Did
> >> you or Steve re do the connections to the Maf sensor as they were
> >> corroded....as the symptoms were very erratic idle, high idle and
> >> eventually fuel loss. when the breakdown chap played with the
> >> connection it improved and idled properly, when we arrived at yours
> >> it was still idling a little high though.
> >> 
> >> Andy.
> >> 
> >>    ----- Original Message -----
> >>    From: geoff ward
> >>    To: [email protected]
> >>    Sent: Monday, June 07, 2010 11:06 AM
> >>    Subject: Re: [Quantum Owners] Poor idling/running Zetec
> >>    
> >>    
> >>    Jim,
> >>    
> >>    Disconnecting the MAF was very similar to disconnecting the idle
> >>    speed
> >> 
> >> control valve or the throttle position sensor, it will idle at a more
> >> sensible speed but runs really rough. We used the loom from the doner
> >> escort, plastic inlet.
> >> 
> >>    Geoff.
> >>    
> >>    On 7 June 2010 10:54, Jim Hearne<[email protected]>  wrote:
> >>      When you fitted the alloy inlet manifold which injector wiring
> >>      loom
> >> 
> >> did you fit, the one from the alloy manifold or the one from the
> >> Escort plastic manifold ?
> >> 
> >>      As somebody else found recently there are slight wiring
> >>      differences
> >> 
> >> between the 2 involving the cam sensor and air temperature sensors.
> >> 
> >>      Jim
> >>      
> >>      On 07/06/2010 10:42, geoff ward wrote:
> >>        Hi Jim,
> >>        
> >>        Not sure about that, don't know what you mean by throttle pot,
> >> 
> >> hopefully Steve will respond. At the moment the car is in Aylesbury
> >> but has been at Steve's near Woking.
> >> 
> >>        Geoff.
> >>        
> >>        On 7 June 2010 10:28, Jim Hearne<[email protected]>  wrote:
> >>          Did you do any electrical tests on the throttle pot.
> >>          Where is the car ?
> >>          
> >>          Jim
> >>          
> >>          On 07/06/2010 10:19, geoff ward wrote:
> >>            Hi all and thanks again for all the helpful suggestions.
> >>            Steve and I have checked and double checked through all
> >>            that
> >> 
> >> has been suggested, every thing seems to work as it should
> >> individually. The idle speed control vale has been thoroughly cleaned
> >> again and checked to see that it works, then refitted with a new
> >> gasket and that it receives input, electronically, from its plug.
> >> Steve has checked all the connections with his testing equipment,
> >> it's all beyond me!, and it all works. We have reset the ECU yet
> >> again, despite spending all day Saturday trying to get it to run
> >> properly, it still has the same problem. Thank you Steve for all the
> >> time and effort you have put in so far to try and fix it. So if any
> >> of you have any further suggestions, we would be pleased to hear
> >> them, as Carole and I are getting worried now, with only one weekend
> >> to go before we head to Scotland.
> >> 
> >>            Yours hopefully Geoff.
> >>            
> >>            
> >>            On 1 June 2010 22:59, geoff ward<[email protected]>
> >> 
> >> wrote:
> >>              Thank you to all for your help and advice, I will do a
> >>              bit
> >> 
> >> more checking and cleaning of contacts etc  tomorrow. The strangest
> >> thing,as Steve mentioned in his original post, is that the engine
> >> idles perfectly at around 900 - 1000 rpm (according to the XR2 rev
> >> counter) when you first start it up. I have followed the method for
> >> resetting the ECU 4 times know and it has had good idle speed every
> >> time for the first stage of the reset, ie allow to idle for 10 -15
> >> mins (DO NOT TOUCH THE THROTTLE) it only goes all wrong after that!
> >> As soon as you start to drive it, that's when it wont idle properly
> >> anymore.
> >> 
> >>              Carole say thank you all.
> >>              
> >>              Regards, Geoff.
> >>              
> >>              On 1 June 2010 12:29, Steve Kodz<[email protected]>
> >> 
> >> wrote:
> >>                We're getting a very bad idle with the Zetec in
> >>                Carole's
> >> 
> >> 2+2.  With the idle speed control valve connected from cold it will
> >> idle nicely at around 1000rpm, if just left to idle and warm through.
> >> However if you rev, or drive that car the best idle to can get is
> >> between 2-3,000 rpm, which isn't great :(  The car also drives badly,
> >> having hesitation and then you fight the engine on the over run.
> >> 
> >>                It is a lot better with the ISCV disconnected, but
> >>                still
> >> 
> >> not great.  The idle is still a bit high, being around 1,200 rpm and
> >> it still doesn't drive that great.
> >> 
> >>                We've tried resetting the ECU to re-program it and
> >>                Geoff's
> >> 
> >> cleaned all the electrical contact and the ISCV.  Any ideas what else
> >> needs to be done to get this ready before the HHII?
> >> 
> >>                Regards,
> >>                Steve
> >>                --
> >>                www.h4-turbo.co.uk
> >>                www.quantumowners.co.uk
> >>                www.quantumcars.co.uk
> >>                www.quantumheritage.co.uk
> >>                
> >>                --
> >>                You received this message because you are subscribed to
> >>                the
> >> 
> >> Google Groups "Quantum Owners Group" group. To post to this group,
> >> send email to [email protected] To unsubscribe from this
> >> group, send email to [email protected] For
> >> more options, visit this group at
> >> http://groups.google.com/group/quantumowners?hl=en
> >> 
> >>                IMPORTANT NOTE: All information presented herewith is
> >> 
> >> provided on an "As Is" basis, without warranty or the implication
> >> thereof. Neither the Quantum Owners Club nor the individuals
> >> associated with the Quantum Owners Club or in the preparation of the
> >> above information shall have any liability to any person or entity
> >> with respect to liability, loss, or damage caused or alleged to be
> >> caused directly or indirectly by the instructions contained within
> >> this or related message(s).
> >> 
> >>            You received this message because you are subscribed to the
> >> 
> >> Google Groups "Quantum Owners Group" group. To post to this group,
> >> send email to [email protected] To unsubscribe from this
> >> group, send email to [email protected] For
> >> more options, visit this group at
> >> http://groups.google.com/group/quantumowners?hl=en
> >> 
> >>            IMPORTANT NOTE: All information presented herewith is
> >>            provided
> >> 
> >> on an "As Is" basis, without warranty or the implication thereof.
> >> Neither the Quantum Owners Club nor the individuals associated with
> >> the Quantum Owners Club or in the preparation of the above
> >> information shall have any liability to any person or entity with
> >> respect to liability, loss, or damage caused or alleged to be caused
> >> directly or indirectly by the instructions contained within this or
> >> related message(s).
> >> 
> >>          You received this message because you are subscribed to the
> >> 
> >> Google Groups "Quantum Owners Group" group. To post to this group,
> >> send email to [email protected] To unsubscribe from this
> >> group, send email to [email protected] For
> >> more options, visit this group at
> >> http://groups.google.com/group/quantumowners?hl=en
> >> 
> >>          IMPORTANT NOTE: All information presented herewith is
> >>          provided on
> >> 
> >> an "As Is" basis, without warranty or the implication thereof. Neither
> >> the Quantum Owners Club nor the individuals associated with the
> >> Quantum Owners Club or in the preparation of the above information
> >> shall have any liability to any person or entity with respect to
> >> liability, loss, or damage caused or alleged to be caused directly or
> >> indirectly by the instructions contained within this or related
> >> message(s).
> >> 
> >>        You received this message because you are subscribed to the
> >>        Google
> >> 
> >> Groups "Quantum Owners Group" group. To post to this group, send email
> >> to [email protected] To unsubscribe from this group, send
> >> email to [email protected] For more options,
> >> visit this group at http://groups.google.com/group/quantumowners?hl=en
> >> 
> >>        IMPORTANT NOTE: All information presented herewith is provided
> >>        on
> >> 
> >> an "As Is" basis, without warranty or the implication thereof. Neither
> >> the Quantum Owners Club nor the individuals associated with the
> >> Quantum Owners Club or in the preparation of the above information
> >> shall have any liability to any person or entity with respect to
> >> liability, loss, or damage caused or alleged to be caused directly or
> >> indirectly by the instructions contained within this or related
> >> message(s).

-- 
You received this message because you are subscribed to the Google Groups 
"Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners 
Club nor the individuals associated with the Quantum Owners Club or in the 
preparation of the above information shall have any liability to any person or 
entity with respect to liability, loss, or damage caused or alleged to be 
caused directly or indirectly by the instructions contained within this or 
related message(s).

Reply via email to