Did you do any electrical tests on the throttle pot.
Where is the car ?

Jim


On 07/06/2010 10:19, geoff ward wrote:
Hi all and thanks again for all the helpful suggestions.
Steve and I have checked and double checked through all that has been suggested, every thing seems to work as it should individually. The idle speed control vale has been thoroughly cleaned again and checked to see that it works, then refitted with a new gasket and that it receives input, electronically, from its plug. Steve has checked all the connections with his testing equipment, it's all beyond me!, and it all works. We have reset the ECU yet again, despite spending all day Saturday trying to get it to run properly, it still has the same problem. Thank you Steve for all the time and effort you have put in so far to try and fix it. So if any of you have any further suggestions, we would be pleased to hear them, as Carole and I are getting worried now, with only one weekend to go before we head to Scotland.
Yours hopefully Geoff.

On 1 June 2010 22:59, geoff ward <[email protected] <mailto:[email protected]>> wrote:

    Thank you to all for your help and advice, I will do a bit more
    checking and cleaning of contacts etc  tomorrow. The strangest
    thing,as Steve mentioned in his original post, is that the engine
    idles perfectly
    at around 900 - 1000 rpm (according to the XR2 rev counter) when
    you first start it up. I have followed the method for resetting
    the ECU 4 times know and it has had good idle speed every time for
    the first stage of the reset, ie allow to idle for 10 -15 mins (DO
    NOT TOUCH THE THROTTLE) it only goes all wrong after that! As soon
    as you start to drive it, that's when it wont idle properly anymore.
    Carole say thank you all.
    Regards, Geoff.
    On 1 June 2010 12:29, Steve Kodz <[email protected]
    <mailto:[email protected]>> wrote:

        We're getting a very bad idle with the Zetec in Carole's 2+2.
         With the idle
        speed control valve connected from cold it will idle nicely at
        around
        1000rpm, if just left to idle and warm through.  However if
        you rev, or
        drive that car the best idle to can get is between 2-3,000
        rpm, which isn't
        great :(  The car also drives badly, having hesitation and
        then you fight
        the engine on the over run.

        It is a lot better with the ISCV disconnected, but still not
        great.  The
        idle is still a bit high, being around 1,200 rpm and it still
        doesn't drive
        that great.

        We've tried resetting the ECU to re-program it and Geoff's
        cleaned all the
        electrical contact and the ISCV.  Any ideas what else needs to
        be done to
        get this ready before the HHII?

        Regards,
        Steve
        --
        www.h4-turbo.co.uk <http://www.h4-turbo.co.uk/>
        www.quantumowners.co.uk <http://www.quantumowners.co.uk/>
        www.quantumcars.co.uk <http://www.quantumcars.co.uk/>
        www.quantumheritage.co.uk <http://www.quantumheritage.co.uk/>

        --
        You received this message because you are subscribed to the
        Google Groups "Quantum Owners Group" group.
        To post to this group, send email to
        [email protected]
        <mailto:[email protected]>
        To unsubscribe from this group, send email to
        [email protected]
        <mailto:[email protected]>
        For more options, visit this group at
        http://groups.google.com/group/quantumowners?hl=en

        IMPORTANT NOTE: All information presented herewith is provided
        on an "As Is" basis, without warranty or the implication
        thereof. Neither the Quantum Owners Club nor the individuals
        associated with the Quantum Owners Club or in the preparation
        of the above information shall have any liability to any
        person or entity with respect to liability, loss, or damage
        caused or alleged to be caused directly or indirectly by the
        instructions contained within this or related message(s).



--
You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).

--
You received this message because you are subscribed to the Google Groups "Quantum 
Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor 
the individuals associated with the Quantum Owners Club or in the preparation of the 
above information shall have any liability to any person or entity with respect to 
liability, loss, or damage caused or alleged to be caused directly or indirectly by the 
instructions contained within this or related message(s).

Reply via email to