Hi list, First, Derek:
I think your reply was a) off topic and b) down right rude. Please publicly apologise. I don't know you Derek and I don't know Neil either, but Neil's questions are genuine - if a little hard to read), your response was not. Now, as they say: please redirect all further flames to /dev/nul. In other words, let that be an end of it. Thank you. ----------- Now, Neil, your questions: The golden rule for both note and control editors when using a screen reader is to keep checking the status bar at the bottom of the screen. The status bar lists: Start: the start time of the event, or cursor position Channel: the MIDI channel number of the event Then, for note view, you have: Key: Note key number Vel: Note velocity Len: Note length For the Control editor, you have: Num: The controller number (which includes the special ones 128-131) Val: Controller value At the end, it says either "Ins" or "Mod". If it says Ins, then the cursor is not on an event and pressing the Insert button will insert a new event. (I am using the word "event" generically to mean note or controller, the same works in either editor). If it says "mod", then the cursor is on an event and you can modify it. Pressing ALT+LEFT and ALT+RIGHT will move between events in either editor. However, there is a difference: in the note editor, the note you land on will be played; in the control editor, the control you land on will not. This is mainly because it is not so obvious what controllers are doing as they do not make any sound and, in some cases, sending only certain controllers could render your synth silent ... So, to summarise again, when you use the controller editor or note editor, press ALT+LEFT or ALT+RIGHT to move to the previous or next event, then check out the status bar. Now instrument lists: I do not have lists for either the Roland Juno D or the Yamaha CL280, but if you have the relevant manual pages available, I'm sure they can be created. Hope all this helps. James > ----Original Message---- > From: [EMAIL PROTECTED] > Date: Oct 5, 2007 1:02:58 AM > To: QWS list <[email protected]> > Subj: Re: QWS List qws acessiblity forblind users > > The first step in getting things to read with your setup is formatting your > messages so that they're at least coherent to an eloquence user. > Eloquence gives people loads of headroom for misspellings, as I have learned > the hard way. You, therefore, have loads of room for sloppy spelling. > The problem is those low standards are so far above your writing abilities > that you may not have seen them at all. > If you're learning English, I commend you for doing so, and using what > skills you have to the fullest. > However, if English is your first language, I'd recommend pretending it > wasn't, just to be on the safe side. > ----- Original Message ----- > From: "Neil Foster" <[EMAIL PROTECTED]> > To: "QWS list" <[email protected]> > Sent: Thursday, October 04, 2007 7:32 PM > Subject: QWS List qws acessiblity forblind users > > > > hi > > I am using qws but I am blind and having problems with my scren reader > > and the controller and note editor. can move about noters pressing alt > > left and right but can't find anywya to get at program changes I have > > tried setting teh num value to 128 and 131 to get program changes and > > tempo cahnges respectively whichI think are thre correct values but I'm > > not getting any controllers . Are there any ohter blind users who use qws > > with ascren reader who can suggest way to get at teh controller > > infomation. As I understanding from teh helpfile it only lists teh > > controllers you specify in teh num value. > > > > any help gratefully recived. > > > > also has anyone got instrumetn lists for a roldand juno d and yamaha > > clavinola cl280? > > > > thank you > > > > neil foster > > To unsubscribe or change list options, see http://lists.andrelouis. com > > > > > To unsubscribe or change list options, see http://lists.andrelouis.com To unsubscribe or change list options, see http://lists.andrelouis.com
