I'm trying to fire aux log one from main log using a macro cart with PN 2 1! But no joy. If I start aux 1 by hand it fires. Hmmm. Does PN work in 1.7.2?
On 18/03/2013, at 15:50, Gavin Stephens <[email protected]> wrote: > Yes it has lease line mode fir two or four wire operation. Although it sits > there with a modem tone in that mode constantly unfortunately. It's whether I > can keep it quiet and off hook so It dials instantly. I'll have a play with > it though. > > On 18/03/2013, at 15:43, VE4PER/ Andy <[email protected]> wrote: > >> imagine it would as a lot of ext modems came so you could set them up on >> a dedicated live cct without using dial up capabilities >> >> On 18/03/13 02:38, Gavin Stephens wrote: >>> Ah never thought of that. I have an old 28k external modem. I'll just have >>> to see if it'll stay off hook I'll go read the manual. >>> >>> On 18/03/2013, at 15:24, VE4PER/ Andy <[email protected]> wrote: >>> >>>> maybe suggestion here of using dtmfdial app to generate audio tone >>>> strings and use a cart recording to play directly to aud channel? >>>> >>>> is it over a dedicated serial circuit where a standard modem in dial >>>> mode might work? >>>> >>>> On 18/03/13 02:18, Gavin Stephens wrote: >>>>> Yes that is the Intuitive board I looked at. I emailed about it but it >>>>> requires that the automation system wait for an acknowledgement from the >>>>> board before sending the next character. However it requires two >>>>> characters before it can make a tone grrrr. It doesn't take the while >>>>> string in one swoop. >>>>> >>>>> On 18/03/2013, at 15:12, VE4PER/ Andy <[email protected]> wrote: >>>>> >>>>>> something like this >>>>>> >>>>>> http://www.icircuits.com/prod_dtmfenc232.html >>>>>> >>>>>> >>>>>> On 18/03/13 01:48, Gavin Stephens wrote: >>>>>>> Does anyone have any ideas for something that can do this in RD... >>>>>>> >>>>>>> I've looked at inituitive circuits boards but they have >>>>>>> acknowledgements between characters sent so no go. I've also looked at >>>>>>> circuitwerkes genr8 but it requires minimum 30ms delay between sending >>>>>>> characters etc.... Does anyone know of anything that will take an rs232 >>>>>>> serial out string all at once from RD and turn this in dtmf without >>>>>>> character delays or acknowledgement waits etc...? I'd rather use DTMF >>>>>>> than sub-audible tones over an AAC independent stereo stream (left mono >>>>>>> programme/right DTMF). >>>>>>> >>>>>>> >>>>>>> >>>>>>> _______________________________________________ >>>>>>> Rivendell-dev mailing list >>>>>>> [email protected] >>>>>>> http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev >>>>>> _______________________________________________ >>>>>> Rivendell-dev mailing list >>>>>> [email protected] >>>>>> http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev >>>>> _______________________________________________ >>>>> Rivendell-dev mailing list >>>>> [email protected] >>>>> http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev >>>> _______________________________________________ >>>> Rivendell-dev mailing list >>>> [email protected] >>>> http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev >>> _______________________________________________ >>> Rivendell-dev mailing list >>> [email protected] >>> http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev >> >> _______________________________________________ >> Rivendell-dev mailing list >> [email protected] >> http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev > > _______________________________________________ > Rivendell-dev mailing list > [email protected] > http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev _______________________________________________ Rivendell-dev mailing list [email protected] http://lists.rivendellaudio.org/mailman/listinfo/rivendell-dev
