[Elecraft] K3 No power out
Yes I can set it at 35 watts which is what I usually use to drive the KPA 500, and speak in the mic for ssb and get no power out. In cw at the same 35 watts, when I send code either straight key or padfle. 0 watts out. Same results if I attempt to run bearfoot at 100 watts or 5 watts, I get no power out. Receive is working fine, the P3 is working normal, and the KPA 500 and KAT 500 track bands as I change them. I will try again tomorrow after a night of sleep. If still no go, will phone home to Elecraft Don, W4CBS Sent from Yahoo Mail on Android __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 No power out
Elecraft service set my Tune Pwr to 5.1 watts to prevent ‘inadvertent running of TX gain calibration’. Have you tried running the TX gain calibration with the K3 Utility? -- Mike Flowers, K6MKF, NCDXC - "It's about DX!" > On Aug 14, 2018, at 5:31 PM, Dennis Moore wrote: > > "No power to tune anything." Does this mean you've only tried to tune, and > haven't tried actually transmitting cw or phone? If so, and I don't know how > it would have changed, have you checked the Menu-Config-TUN PWR to see what > it is set to? If it is set to .1 it will show 0.0 > > 73, Dennis NJ6G > > >> On 8/14/2018 17:19, Don Roberts via Elecraft wrote: >> I have enjoyed the wisdom of this group and have learned so much but now it >> is my time to ask for help. My K3 is showing no power out. I have the K >> line. The relay clicks when going from 11 to 12 watts. I can set the power >> up to 110, but when I hit tune I get zere watts shown and verified by my >> watt meters. Makes no difference of mode, band, dummy load, resonant ant, or >> multiband hex beam, 80 meter horizontal loop, or 40 meter vertical. There is >> no output to tune anything. >> My last contacts showed no problems. Worked 10 meter cw, 20 and 6 meter ssb >> ok just two days ago. It seems to be receiving fine. The P3 display is >> normal, the KAT 500 and KPA 500 change bands with the K3 as they normally >> do. I have rebooted the K3 several times and have killed the master AC power >> to everything only to bring it up to the same thing. The ALC, compression, >> mic gain all register correct, where I always run them. I have checked to >> make sure the Test button has not been ingaged. Press XMIT and all I get is >> 0 W. I am sure I have forgotten something simple. Would appreciate any >> help. Thanks >> 73, Don W4CBS > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to mike.flow...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 No power out
"No power to tune anything." Does this mean you've only tried to tune, and haven't tried actually transmitting cw or phone? If so, and I don't know how it would have changed, have you checked the Menu-Config-TUN PWR to see what it is set to? If it is set to .1 it will show 0.0 73, Dennis NJ6G On 8/14/2018 17:19, Don Roberts via Elecraft wrote: I have enjoyed the wisdom of this group and have learned so much but now it is my time to ask for help. My K3 is showing no power out. I have the K line. The relay clicks when going from 11 to 12 watts. I can set the power up to 110, but when I hit tune I get zere watts shown and verified by my watt meters. Makes no difference of mode, band, dummy load, resonant ant, or multiband hex beam, 80 meter horizontal loop, or 40 meter vertical. There is no output to tune anything. My last contacts showed no problems. Worked 10 meter cw, 20 and 6 meter ssb ok just two days ago. It seems to be receiving fine. The P3 display is normal, the KAT 500 and KPA 500 change bands with the K3 as they normally do. I have rebooted the K3 several times and have killed the master AC power to everything only to bring it up to the same thing. The ALC, compression, mic gain all register correct, where I always run them. I have checked to make sure the Test button has not been ingaged. Press XMIT and all I get is 0 W. I am sure I have forgotten something simple. Would appreciate any help. Thanks 73, Don W4CBS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] P3 Firmware update fails.... ME TOO
oops ! my serial port was denying access.. MY BAD using p3 utility 1.16.3.15.. have MCU 1.59 svga 1.33 and when I check available I get 1.54 & 1.25 """ P3 MCU revision 01.59. RS-232 speed 38400 bit/s. 20:15:43 Opening connection to ftp.elecraft.com 20:15:43 Copying files to C:\Program Files (x86)\Elecraft\P3 Utility 20:15:43 FtpGetFile completed with error 0x0005: Access is denied what am I doing wrong At 02:22 AM 8/14/2018, TL_Netvision wrote: Hi all I am trying to upgrade a P3 MCU 1.29 to 1.54 and\or 1.60 (No SVGA option installed). When I hit "send checked items to P3" the relays click every 2 seconds and I see 2 messages repeat forever: 1. "Attempting to connect P3 on port COM1 at 38400 bit/s" in the P3's utility window, 2. "Checking for SVGA" on the P3's screen. No uploading is performed & I can terminate the loop only with the "cancel" button. Environment: -P3 utility ver 1.16.3.1 -P3 is connected only to PS (13.8v external) & PC (Genuine full RS-232 cable). -All files are present in the "P3 firmware" folder (Windows 10 1803 build 17134). Any ideas please? Thanks in advance, Isaac, 4Z1TL --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@arrl.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 No power out
I have enjoyed the wisdom of this group and have learned so much but now it is my time to ask for help. My K3 is showing no power out. I have the K line. The relay clicks when going from 11 to 12 watts. I can set the power up to 110, but when I hit tune I get zere watts shown and verified by my watt meters. Makes no difference of mode, band, dummy load, resonant ant, or multiband hex beam, 80 meter horizontal loop, or 40 meter vertical. There is no output to tune anything. My last contacts showed no problems. Worked 10 meter cw, 20 and 6 meter ssb ok just two days ago. It seems to be receiving fine. The P3 display is normal, the KAT 500 and KPA 500 change bands with the K3 as they normally do. I have rebooted the K3 several times and have killed the master AC power to everything only to bring it up to the same thing. The ALC, compression, mic gain all register correct, where I always run them. I have checked to make sure the Test button has not been ingaged. Press XMIT and all I get is 0 W. I am sure I have forgotten something simple. Would appreciate any help. Thanks 73, Don W4CBS Sent from Yahoo Mail on Android __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] P3 Firmware update fails.... ME TOO
using p3 utility 1.16.3.15.. have MCU 1.59 svga 1.33 and when I check available I get 1.54 & 1.25 """ P3 MCU revision 01.59. RS-232 speed 38400 bit/s. 20:15:43 Opening connection to ftp.elecraft.com 20:15:43 Copying files to C:\Program Files (x86)\Elecraft\P3 Utility 20:15:43 FtpGetFile completed with error 0x0005: Access is denied what am I doing wrong At 02:22 AM 8/14/2018, TL_Netvision wrote: Hi all I am trying to upgrade a P3 MCU 1.29 to 1.54 and\or 1.60 (No SVGA option installed). When I hit "send checked items to P3" the relays click every 2 seconds and I see 2 messages repeat forever: 1. "Attempting to connect P3 on port COM1 at 38400 bit/s" in the P3's utility window, 2. "Checking for SVGA" on the P3's screen. No uploading is performed & I can terminate the loop only with the "cancel" button. Environment: -P3 utility ver 1.16.3.1 -P3 is connected only to PS (13.8v external) & PC (Genuine full RS-232 cable). -All files are present in the "P3 firmware" folder (Windows 10 1803 build 17134). Any ideas please? Thanks in advance, Isaac, 4Z1TL --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@arrl.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KPA 1500 and ICom 7560 Pro2 control
Would a CI-V cable work for you? I personally tested IC7600 and 7300 and I’ve been told that 7610 also works. The amp looks for the TX frequency message from the exciter. I’m not sure whether a 765 pro 2 sends that. If it doesn’t, I can teach KPA1500 firmware to look for the frequency message the 765 sends as you move the VFO, if I can figure out what that is. We want the TX VFO freq to deal with split and XIT. I’m away from my notes, but I think the CI-V message might be 1C with a sub code 3 for tx freq. If you connect the radio to amp via CI-V, check the XCVR FREQ status page, that comes from the CI-V message. Also choose Icom on the RADIO TYPE menu. There’s is a speed to match up and the radio needs to know to send TX freq messages on QSY, that’s called transceive in some icom documents. 73 de Dick, K6KR Sent from my iPhone > On Aug 14, 2018, at 15:28, Cody C via Elecraft > wrote: > > Good day group I am wondering is there a way to change bandson my KPA 1500 by > selecting the band on my ICom 756 Pro 2. I have no issueswith the changing > bands via a Rf burst. But I would really like it to change bands but > selecting the correct band from my radio. > > > > Thanks you in advance > > Cody > > KC2LSD > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to d...@elecraft.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] KPA 1500 and ICom 7560 Pro2 control
Good day group I am wondering is there a way to change bandson my KPA 1500 by selecting the band on my ICom 756 Pro 2. I have no issueswith the changing bands via a Rf burst. But I would really like it to change bands but selecting the correct band from my radio. Thanks you in advance Cody KC2LSD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S settings for Heil HM-10 XD microphone
Does Heil have the settings on their website? I seem to recall they do. That is a good place to start. Bob, K4TAX Sent from my iPhone > On Aug 14, 2018, at 1:58 PM, Thomas Donohue wrote: > > I recently purchased subject mic and will be connecting it to the K3S > shortly. Before I do that, I was wondering what mic settings to use? I > currently have a Heil PR-10 mic and am using the MIC FP HI menu setting and a > mic gain of 20; the PR-10 works fine, but I wanted to get a mic that I could > switch back and forth from the wide HC-5X cartridge to the narrow or DX HC-4X > cartridge, thus the HM-10 XD. I have purchased the XLR 4 pin CC-1, connecting > cable to replace the XLR 3 pin cable that I use with the PR-10 for connection > to the FP Mic connector. The PR-10 has a 600 ohm balance impedance while the > HM-10 XD has a 600 ohm impedance, unbalanced, I guess. To begin I intend to > use the MIC FP HI menu setting. Does anyone see a problem with that or is > there anyone using a HM-10 XD that can offer some suggested settings. Any > response or info will be appreciated. > > Best 73, > Tom/W1QU > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to rmcg...@blomand.net > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S settings for Heil HM-10 XD microphone
I recently purchased subject mic and will be connecting it to the K3S shortly. Before I do that, I was wondering what mic settings to use? I currently have a Heil PR-10 mic and am using the MIC FP HI menu setting and a mic gain of 20; the PR-10 works fine, but I wanted to get a mic that I could switch back and forth from the wide HC-5X cartridge to the narrow or DX HC-4X cartridge, thus the HM-10 XD. I have purchased the XLR 4 pin CC-1, connecting cable to replace the XLR 3 pin cable that I use with the PR-10 for connection to the FP Mic connector. The PR-10 has a 600 ohm balance impedance while the HM-10 XD has a 600 ohm impedance, unbalanced, I guess. To begin I intend to use the MIC FP HI menu setting. Does anyone see a problem with that or is there anyone using a HM-10 XD that can offer some suggested settings. Any response or info will be appreciated. Best 73, Tom/W1QU __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] [K3] For Sale, K3 with new synth and AM/FM filters
Posted on behalf of owner by Warren Merkel, KD4Z. K3 Serial # 0632 Factory Assembled. Original owner, non-smoker, climate-controlled environment. Updated with the current firmware revision. Includes original, Elecraft bound manuals (construction and operating), power cable, and optional hand mic. It has the following options installed: 1.KTCXO-1 TCXO 1 PPM 2.KSYN3A Synthesizer Board (New Synth) 3.KNB3 Noise Blanker Board 4.Battery Cover (is part of the 2nd Receiver kit -- 2nd RX board not included) 5.KBPF3A General Coverage Filter Board 6.KFL3A-2.7 kHZ Filter 7.KFL3a-6K AM Filter 8.KFL3B FM Filter 9.KXV3B Interface This radio works extremely well and is cosmetically in excellent condition. Just purchased a new K3s and no longer need this radio. It was last used as one of the CW stations at our "All Elecraft" Field Day and performed flawlessly. Price is: $2350 Firm. Sorry, CONUS only. Price includes shipping. Please direct inquiries to owner (not me! John isn't on this reflector --yet) : John Norris, N4IHV jw...@bellsouth.net (404) 307-5578 Roswell, Georgia __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] OT-Junk Mail & Spam Robo Calls
Thanks for your patience, Eric. (:-)) 73 all K0PP On Tue, Aug 14, 2018, 10:05 Eric Swartz - WA6HHQ, Elecraft < e...@elecraft.com> wrote: > We're drifting a little too OT. Let's close this thread in the interest of > reducing email overload for our readers. > > 73, > Eric > Moderator etc. > /elecraft.com/ > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] OT-Junk Mail & Spam Robo Calls
We're drifting a little too OT. Let's close this thread in the interest of reducing email overload for our readers. 73, Eric Moderator etc. /elecraft.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] OT-Junk Mail & Spam Robo Calls
My solution is very simple. I ignore all calls unless they appear on my caller ID from my contact list. Likewise on e-mail, my spam filter gets 99.9% of all of them and they end being sent to the junk folder. That folder gets emptied every 12 hrs. The one or two that get through, also get manually added to the junk filter. Thank you Thunderbird which is my e-mail application. Once the filter is set, they are then history forever. 73 Bob, K4TAX On 8/14/2018 10:35 AM, Terry Schieler wrote: I use commercial spam solutions for relief from internet email spammers. Lots of them out there. That's all well and good. The REAL problem for me are robo calls to my home phones and cell phone. I listed both phones on the State of Missouri and the Federal *No Call Lists* years ago. That worked ok for a while, then totally spiraled out of control. Spammers don't pay any attention to the *List* and violations are not enforced. I found a fix in an app called *NOMOROBO* No More Robo (calls). After you sign up for the service, their server spots the fingerprints of incoming spam telephone robo calls on your phone line. My phone rings a partial ring (.5 sec?) then the software at the server end sucks the call off my line and adds it to their national database blacklist. The Caller Id is still displayed on my TV screen, but before I can get my butt out of my chair, the ring stops, telling me not to bother with the call, it's spam. I can't remember how many years I've used NoMoRobo but I was an early adopter and it has been working beautifully for probably 10 years now. The idea was hatched by a couple of guys during a contest to find a solution to annoying Robo Calls (necessary because your local telco doesn't want to help inhibit the use of their paid services). You don't need to load your *white list* phone numbers. There is a free version of NoMoRobo and a paid version. So far, I have seen no need for the paid version. In all this time I only had two callers get wrongly *captured* by the spam software and both were vendors I use who had recently changed their phone number. Calls from my doctor's appointment office, Trash Hauler, etc come right through. While not affiliated with the firm that offers this (I wish I were) I recommend looking it over and deciding for yourself if it suits your needs: www.nomorobo.com 73, Terry WØFM Pardon the bandwidth -Original Message- From: Ken G Kopp [mailto:kengk...@gmail.com] Sent: Monday, August 13, 2018 1:58 PM To: w7aqk Cc: Elecraft Subject: [Elecraft] OT-Junk Mail Hi Dave, + rest of list I've not seen your "Elycraft", but we … both ElecraftCovers (Rose, N7HKW) and me … get lots of e-mail from people wanting to "fix" elecraft.com and bring us more business. I expect Elecraft also gets these same offers. Both of us, for several reasons, need to maintain an old-fashioned wired phone line. We have had the same number for about fifty years and it's published and used from all over the world. Here's what seems to (partially) work for us; we have an answering machine in a speaker-phone that's audible throughout the house. In addition, our satellite TV provider is connected to the TV set … which is usually on (;-) … and the TV screen displays caller ID info. Perhaps ten percent of the calls are legit. Both of us have Verizon cell phones and get -many- calls from spoofed numbers … usually in our 406 area and often using a "local" number. Rose gets many calls related to her Elecraft case and cover business that she -must- answer. She's had three today … with two being spoofed. We both use G-Mail as our e-mail provider and to G-mail's credit, we get very little SPAM. We also use Norton ... wouldn't be without it. Our internet provider (Century Link) is via cable. FWIW 73! K0PP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rmcg...@blomand.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] OT-Junk Mail & Spam Robo Calls
I use commercial spam solutions for relief from internet email spammers. Lots of them out there. That's all well and good. The REAL problem for me are robo calls to my home phones and cell phone. I listed both phones on the State of Missouri and the Federal *No Call Lists* years ago. That worked ok for a while, then totally spiraled out of control. Spammers don't pay any attention to the *List* and violations are not enforced. I found a fix in an app called *NOMOROBO* No More Robo (calls). After you sign up for the service, their server spots the fingerprints of incoming spam telephone robo calls on your phone line. My phone rings a partial ring (.5 sec?) then the software at the server end sucks the call off my line and adds it to their national database blacklist. The Caller Id is still displayed on my TV screen, but before I can get my butt out of my chair, the ring stops, telling me not to bother with the call, it's spam. I can't remember how many years I've used NoMoRobo but I was an early adopter and it has been working beautifully for probably 10 years now. The idea was hatched by a couple of guys during a contest to find a solution to annoying Robo Calls (necessary because your local telco doesn't want to help inhibit the use of their paid services). You don't need to load your *white list* phone numbers. There is a free version of NoMoRobo and a paid version. So far, I have seen no need for the paid version. In all this time I only had two callers get wrongly *captured* by the spam software and both were vendors I use who had recently changed their phone number. Calls from my doctor's appointment office, Trash Hauler, etc come right through. While not affiliated with the firm that offers this (I wish I were) I recommend looking it over and deciding for yourself if it suits your needs: www.nomorobo.com 73, Terry WØFM Pardon the bandwidth -Original Message- From: Ken G Kopp [mailto:kengk...@gmail.com] Sent: Monday, August 13, 2018 1:58 PM To: w7aqk Cc: Elecraft Subject: [Elecraft] OT-Junk Mail Hi Dave, + rest of list I've not seen your "Elycraft", but we … both ElecraftCovers (Rose, N7HKW) and me … get lots of e-mail from people wanting to "fix" elecraft.com and bring us more business. I expect Elecraft also gets these same offers. Both of us, for several reasons, need to maintain an old-fashioned wired phone line. We have had the same number for about fifty years and it's published and used from all over the world. Here's what seems to (partially) work for us; we have an answering machine in a speaker-phone that's audible throughout the house. In addition, our satellite TV provider is connected to the TV set … which is usually on (;-) … and the TV screen displays caller ID info. Perhaps ten percent of the calls are legit. Both of us have Verizon cell phones and get -many- calls from spoofed numbers … usually in our 406 area and often using a "local" number. Rose gets many calls related to her Elecraft case and cover business that she -must- answer. She's had three today … with two being spoofed. We both use G-Mail as our e-mail provider and to G-mail's credit, we get very little SPAM. We also use Norton ... wouldn't be without it. Our internet provider (Century Link) is via cable. FWIW 73! K0PP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [KPA500] How to uninstall KPA500/KAT500
Got it. I had only looked under Elecraft. Thanks! 73, Jim N7US -Original Message- Hi Jim Look under Elecraft or KPA500. My KPA500 program is there in add/remove. Mike va3mw On Tue, Aug 14, 2018 at 8:55 AM, Jim N7US wrote: > How can I uninstall the KPA500 and KAT500 Remote programs? I don't > see them listed in Device Manager's Programs and Features. > > > > 73, Jim N7US __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [KPA500] How to uninstall KPA500/KAT500
Hi Jim Look under Elecraft or KPA500. My KPA500 program is there in add/remove. Mike va3mw On Tue, Aug 14, 2018 at 8:55 AM, Jim N7US wrote: > How can I uninstall the KPA500 and KAT500 Remote programs? I don't see > them > listed in Device Manager's Programs and Features. > > > > 73, Jim N7US > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to va...@portcredit.net > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] [KPA500] How to uninstall KPA500/KAT500
How can I uninstall the KPA500 and KAT500 Remote programs? I don't see them listed in Device Manager's Programs and Features. 73, Jim N7US __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Summary: Genovation keypad & K3/K3S
Hello Stefan, I remember running into some roadblock in doing this, but I don't remember what it was now... I initially wanted to connect directly to the K3 as well. I think it was if you had a P3 SVGA, it worked better. If you get things running on just the K3 send me the info, and I'll add it to the web page at: https://www.nk7z.net/adding-external-keypad-k3/ as an addendum to the Genovation page, of course giving you credit for the work. 73s and thanks, Dave (NK7Z/NNR0DC) https://www.nk7z.net ARRL Technical Specialist On 08/14/2018 03:06 AM, Stefan von Baltz, DL1IAO wrote: I did get one reply on this topic. Dave NK7Z has already documented nicely on his website how to connect a Genovation keypad to the P3. The question was how to connect it directly to the K3/K3S, if possible at all, in order to free the P3’s USB-port. A pre-Genovation "button box" was hooked up to the K3’s RS232 port. It uses its internal memory to store the macros and not the available K3 macros. In order to be able to get the K3 to recognize and share several RS232 ports LP-BRIDGE is used to create several virtual serial ports. CAT on one of the virtual serial ports and the "button box" to another. One has to bridge the real "button box" to another of the LPBRIDGE created virtual ports, e.g. with a software called VSPE. It will be up to experimentation if a Genovation keypad can be connected in a similar way. The difference is that the internal K3/K3S memories have to be used. 73, Stefan DL1IAO, SA3CWW/SM9A __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to d...@nk7z.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] Summary: Genovation keypad & K3/K3S
I did get one reply on this topic. Dave NK7Z has already documented nicely on his website how to connect a Genovation keypad to the P3. The question was how to connect it directly to the K3/K3S, if possible at all, in order to free the P3’s USB-port. A pre-Genovation "button box" was hooked up to the K3’s RS232 port. It uses its internal memory to store the macros and not the available K3 macros. In order to be able to get the K3 to recognize and share several RS232 ports LP-BRIDGE is used to create several virtual serial ports. CAT on one of the virtual serial ports and the "button box" to another. One has to bridge the real "button box" to another of the LPBRIDGE created virtual ports, e.g. with a software called VSPE. It will be up to experimentation if a Genovation keypad can be connected in a similar way. The difference is that the internal K3/K3S memories have to be used. 73, Stefan DL1IAO, SA3CWW/SM9A __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] P3 Firmware update fails
Hi all I am trying to upgrade a P3 MCU 1.29 to 1.54 and\or 1.60 (No SVGA option installed). When I hit send checked items to P3 the relays click every 2 seconds and I see 2 messages repeat forever: 1. Attempting to connect P3 on port COM1 at 38400 bit/s in the P3s utility window, 2. Checking for SVGA on the P3s screen. No uploading is performed & I can terminate the loop only with the cancel button. Environment: -P3 utility ver 1.16.3.1 -P3 is connected only to PS (13.8v external) & PC (Genuine full RS-232 cable). -All files are present in the P3 firmware folder (Windows 10 1803 build 17134). Any ideas please? Thanks in advance, Isaac, 4Z1TL --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
