Re: Stus-List Cetol Clear...

I don’t want to start a teak war, but I have to agree with Rick – I’ve had to strip my handrails a few times, as it gets away from me, and now I do again. But I just couldn’t see putting SS rails on the boat. I could have whipped up some SS handrails overnight, but it just didn’t seem right. .

Re: Stus-List Sail Changeover for 29 Mk1

I just discovered this unopened email, From Matt. I put this post out there, partly for you, Matt! I know sometimes you are frustrated, but this is what you have to do - Just tell Bierig to scale up my main a few feet to fit your plan– I don’t know what your boom is, but it should be probably

Stus-List Ronin’s Overdue Refit

Dave, You did a bang-up job of refurbishing your boat! Ronin’s Overdue Refit Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Dave Godwin via CnC-List Sent: Monday, February 19,

Re: Stus-List AIS is alive!

So are you using AIS to find your boat now, instead of that other electronic widget you were using? Or are they both active? Bill Coleman C 39 Erie, PA -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Joe Della Barba via CnC-List Sent: Wednesday,

Re: Stus-List PSS shaft seal

I am so flakey, I know that if I closed all my through hulls I would invariably forget to open them, and either burn up my engine, have warm beer, or some other malady , so I just put new hoses on and check the clamps. Which isn’t a bad idea anyway. Bill Coleman C 39 Erie, PA From:

Re: Stus-List Sail Changeover for 29 Mk1

I think the biggest bang for the buck is a full roach main. Shortly after buying the boat, I got mad at the boom and bought a new extrusion from Charleston, they sell in 2 foot increments. I was telling a friend (who also had a 39, and was an NA Intern at C in the early 70’s) what I was doing,

Re: Stus-List "Maritime Documentation Center"

better than these guys. Regards, Ron Ron Ricci S/V Patriot C 37+ Bristol, RI (978) 877-0369 <mailto:ron.ri...@1968.usna.com> ron.ri...@1968.usna.com From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Coleman via CnC-List Sent: Wednesday, January 24, 2

Re: Stus-List "Maritime Documentation Center"

a, whereas “US Vessel Documentation” was out of California. It’s a coast-to-coast racket. Cheers, Randy On Jan 24, 2018, at 8:38 AM, Bill Coleman via CnC-List <cnc-list@cnc-list.com> wrote: Just got my EARLY supposed Documentation Renewal from the "Maritime Documentatio

Stus-List "Maritime Documentation Center"

Just got my EARLY supposed Documentation Renewal from the "Maritime Documentation Center" I think the USCG must have taken heed of all the complaints, as these people have really toned down their ‘Renewal’ There is no amount to pay, and now little bits in there like , This is a courtesy

Re: Stus-List FASTRACK: AN EPIC VOYAGE

Isn’t there a C named Fastrack in Toronto? Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Ken Heaton via CnC-List Sent: Saturday, January 13, 2018 1:13 PM To: cnc-list Cc: Ken Heaton Subject: Re: Stus-List FASTRACK: AN EPIC

Re: Stus-List 1981 C 36' - Fresh Water Tank Replacement

Just stumbled on this saved video on repairing polyethylene, not sure this was the string talking about it or not . .. https://www.youtube.com/watch?feature=player_embedded =h-9yhanz5DE Bill Coleman C 39 Erie,

Re: Stus-List Cold weather [was Re: Wrapping LifeSling with Sunbrella]

I saw those lizards on the news, laying on the ground, but they said that they just got too cold to function, and came back to life when it warmed up again – Would be nice if the cold would kill some of those huge snakes down there. Bill Coleman C 39 Erie, PAanimated_favicon1 From:

Re: Stus-List Engine idle speed

I am no Diesel Mechanic either, but it seems to me that the governor should be doing all it can to maintain your speed at a minimum idle. I know that mine (Kubota) will absolutely not go above 3,000, I seems that it would also hold, or should hold, at a minimum. Maybe only newer engines do

Re: Stus-List Irma 1 : Ox <1

Really sad. When these boats are gone, they are gone forever, kind of like watching the old barn disappear from the countryside. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Marek Dziedzic via CnC-List Sent: Thursday,

Stus-List Barient 32ST

On Flea Bay, http://www.ebay.com/itm/292274591579?ul_noapp=true Looks nice, no affiliation, Bill Coleman C 39 Erie, PA ___ The bills have started coming in for the year 2018 and have gone up again. October will be our fund raising month. Please

Re: Stus-List Barient 22ST

to get here, 6 or 7 weeks as I recall, but no problem otherwise. http://www.arco-winches.com/products/spares Steve Thomas C Merritt Island, FL C MKIII Port Stanley, ON Bill Coleman via CnC-List <cnc-list@cnc-list.com> wrote: I have a Barien 22 winch with plasti

Stus-List Barient 22ST

I have a Barien 22 winch with plastic jaws, and the top one is cracked. Does anyone know if there is a source for these replacement parts? Thanks, Bill Coleman C 39 Erie, PA ___ This list is supported by the generous donations of our members. If

Re: Stus-List Yacht club weather station

I really like the Davis Instruments, we have one of those at our club, it is invaluable. \ http://www.erieyachtclub.org/weatherlink/ However, I usually access it through Weather underground. Another thought on this is to go down and dirty - I put a cheap Accu-Rite weather station in at the

Re: Stus-List C 35 MK III full set of North racing sails

I am curious why you are selling the Norlam, I thought that was a very good fabric. Did you not like it? I am trying to decide where to go after Pentax. That stuff (Pentax) doesn’t last too long. Bill Coleman C 39 Erie, PA On Fri, Mar 10, 2017 at 1:03 PM, Matthew Schlanger via

Re: Stus-List Hidea Outboard Motor

There was a discussion on NPR last week about how 2 cycle leaf blowers produce more pollution in California than all the cars! Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jim Watts via CnC-List Sent: Sunday, March 12, 2017 9:48 PM To: 1

Re: Stus-List 35 MK I battery locations

I just noticed in my latest Scams Club Flyer they have Duracell Golf Cart batteries for $25 off, limit 6. Bill Coleman C 39 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Della Barba, Joe via CnC-List Sent: Wednesday, January 25, 2017 5:29 PM To:

Re: Stus-List cleaning the engine compartment.

Matt, you probably dissolved a hole in your tank. Chlorine is super corrosive. I put a little chlorine pool pill in my intake strainer, and it corroded the 316 SS screen so bad half of it was gone. Didn’t take that long either. Bill Coleman C 39 From: CnC-List

Stus-List Barient 36 ST winches on Flea Bay

In Case anyone is looking for some Self Tailers. Bill Coleman C 39 Erie, PA NO, this is not spam.

Re: Stus-List Baltimore/Annapolis wet deck repair

I picked up a Skipper ll on EBAY for a couple hundred bucks,  works fine,  then i found a meter bundled with a laser heat sensor at Costco for around 40. I don't remember where that one is, though!  Bill Coleman  Original message From: Kevin Driscoll via CnC-List

Re: Stus-List AIS VHF

Sorry about that. You Canadians are much much more friendly!. Bill Coleman C 39 Erie Original message From: Dave S via CnC-List Date: 10/27/16 13:00 (GMT-07:00) To: C Stus List Cc: Dave S Subject:

Re: Stus-List Fuel tanks

Look for a Kracor or similar,  not another aluminum tank!  Bill Coleman  Original message From: Gary Nylander via CnC-List Date: 10/26/16 19:20 (GMT-05:00) To: cnc-list@cnc-list.com Cc: Gary Nylander Subject:

Re: Stus-List Nova Kool Recharge

I picked up a set of these at a flea market years ago, http://www.ebay.com/itm/refrigerant-gauges-/112150576806?hash=item1a1cb1fea6 :g:OzAAAOSwmfhX4KSC used it on home, shop, car and boat refrigerant systems - one use can pay for it. Your system should list the low and high charges, just

Re: Stus-List C Polars Again

Thanks Randy, That is a sweet page, Thanks for Sharing. I was able to make a .csv and import it into the e-95, (I used the C Polars). Unfortunately it will probably be next spring B4 I see what it does for my Dynamic Vectors/Laylines. Bill Coleman C 39 Erie, PAanimated_favicon1

Re: Stus-List Open CPN

Peter- go to NewEgg and get a USB to go for $1.49 . Heck, while you're at it,   get a half dozen and give some to your friends.  You can plug a mouse into it and have mouse functionality on your Android or tablet.  Not sure about IOS. Bill Coleman C 39 Original message

Re: Stus-List those facts are unbelievable

I'm sure he's unaware it was hacked Bill Coleman  Original message From: mike amirault via CnC-List Date: 9/24/16 10:13 (GMT-05:00) To: cnc-list@cnc-list.com Cc: amira...@bellaliant.net Subject: Re: Stus-List those facts are unbelievable

Re: Stus-List Raymarine exits the instrument, vhf and

Just catching up on this. I think that NMEA 2000 has removed a lot of proprietary barriers, but I agree they all try to have some exclusivity to keep you in their herd. Garmin seems to be the most open, probably because they are the latest Instrument Mfg. to the party. With regards to

Re: Stus-List BlackWatch - C 39 - world tour

Sounds like fun. Looks like you have done a lot of work to the boat. There is another C 39 in Mexico, J Peter White, not sure if he still has the boat or not. He lives in Toronto, except when he is not. Cruises with his two boys. http://blog.cruisingnet.com/ Bill Coleman C 39 Erie, PA

Re: Stus-List Assymetrical spinnaker pole

When we are running way off, say around 160 – 150 in light air, we sometimes put the Genoa Sheet up over the end of the boom. Holds it out nicely, and takes some of the weight off the leech that would pull it down and deform it. Seems to work well for us. Bill Coleman C 39 Erie, PA

Stus-List Earliest C found in Lake Ontario

I am really surprised at the clarity of the water. I guess all the Zebra and Quagga mussels on there must have cleared up the water. http://www.soundingsonline.com/dispatches/295170-video-historic-discovery/?utm_source=soundings-enewsletter

Re: Stus-List Oddball 33-2 deck fill - again

As far as I know, it could only be one of two threads if it is from this country, and that is 1 ½” NPT, and 1 ¼” NPT Probably this, 1-5/8" Deck Fitting, 1-1/4" NozAll Dia., 11.5 Threads/In, Fits All Scandvik 150644 310343503 In stock online. $39.99 Bill Coleman C 39 Erie, PA

Re: Stus-List 2016 North East Rendezvous

That is really cool – ‘Cept it is booked for that weekend. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Robert Gallagher via CnC-List Sent: Tuesday, August 09, 2016 4:48 PM To: cnc-list@cnc-list.com Cc: Robert Gallagher Subject: Re:

Re: Stus-List LED masthead lights and steaming/deck light

ehalf Of Bill Coleman via CnC-List Sent: Tuesday, August 09, 2016 12:04 PM To: cnc-list@cnc-list.com Cc: Bill Coleman <colt...@verizon.net> Subject: Re: Stus-List LED masthead lights and steaming/deck light I will vouch for the deck/steaming light, I got one this spring on Fre

Re: Stus-List 2016 Northeast Rendezvous

Wow, that gave me goose bumps! Makes me want to charter a C on the coast just so I can go! Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Robert Gallagher via CnC-List Sent: Tuesday, August 09, 2016 2:18 PM To: cnc-list@cnc-list.com Cc:

Re: Stus-List LED masthead lights and steaming/deck light

I will vouch for the deck/steaming light, I got one this spring on Fred’s recommendation, and it is sweet! Seems to be sealed. Very bright. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Frederick G Street via CnC-List

Stus-List ST4000+

I have a peculiar problem, My ST4000+ display no longer displays my rudder indicator, altho it still seems to be wired in ok. Also, my heading was locked in at 243 degrees. This makes my little boat on the chart plotter point to 243 degrees, and I cannot use the autopilot. When I try that,

Re: Stus-List holey drawer pull-y thingies?

No, but a good place to start would be Rocklers , Woodworkers supply,  McMaster Carr- there is is a lot of that stuff in the woodworking  business  Bill Coleman  Original message From: Jack Fitzgerald via CnC-List Date: 8/1/16 07:07

Re: Stus-List Cabin sole screws

I took SS helicoils, screwed them onto Vaseline coated 10-24 SS screws, coated them and the enlarged holes with thickened epoxy, and set them in the holes. Then unscrew the screw when set, works great.  Bill Coleman C 39 Original message From: RAYMOND SHIBE via

Re: Stus-List Grounding a mast - 30mki

Now that would have made one hell of a YouTube Video! Bill Coleman C 39 Erie, PA Last week a soft ball player in Nova Scotia was hit and survived. As she reached out to open the door on a storage shed, the shed was struck by lightning. The current went up her arm and out her foot,

Re: Stus-List Singing Rigging

Jim – Have you just tried singing along? . . . Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jim Watts via CnC-List Sent: Tuesday, July 26, 2016 11:16 AM To: 1 CnC List Cc: Jim Watts Subject: Re: Stus-List Singing

Re: Stus-List Singing Rigging

I happen to know a Ph.D on the subject, so I ran it by him : Probably a little more info than anyone needed, but that is Just what we do on this list! << Bill: The winglets and vortex shedding are unrelated. They both involve vortexes but they are different issues. When you have flow

Re: Stus-List Diameter of 33-2 Deck Pump Out Fitting?

Those are just simple quick connectors, available at any Pneumatics store, or even at Tractor Supply for around 5 bucks Most are 1 ½” NPT, altho some are 1 ¼” NPT Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bradley

Re: Stus-List Wednesday Night racing

Randy, I have a childhood friend who has been in the Denver area for some time. He sails, but he might out of Dillon, even tho he is in Southern Denver. Mark DeDenisio, do you know of him? He just bought a Freedom 30 which he has in Oriental, NC which he may retire to in a few years. Bill

Re: Stus-List Wednesday Night racing

Wow, I am surprised that you have 28 PHRF racers at that small lake, it doesn’t look like there are much more that 28 in the whole marina . Even more surprised to find PHRF Racing at 5,000 feet. And I was stunned to see racing, and 8 nice Starboats racing at 9,500 feet at Frisco Bay on

Re: Stus-List Bending Stainless...

Do not apply heat to Stainless. Two things, if hot enough it will anneal it and make it dead soft with little of its former strength, and second, it will likely rust after you do. Stainless can be bent several times before it will break. We cold form all SS, it is simply the way it is done. One

Re: Stus-List Forestay Stem Fitting / Chainplate - Update

I think it is fine. You just need to scrub a little acid on that area to remove the  surface iron Bill Coleman  Original message From: Sam Salter via CnC-List Date: 7/12/16 21:16 (GMT-05:00) To: Aaron Rouhi via CnC-List

Re: Stus-List ST4000+ WheelPilot heading Calibration

You are more than welcome to come over and push buttons, Russ ! This one has me perplexed. I even aligned it straight on into the wind. SB Tack shows 30° Close hauled, PT shows 60° Close Hauled – maybe you are onto something! Bill Coleman C 39 Erie, PA From: CnC-List

Re: Stus-List Forestay Stem Fitting / Chainplate Replacement

I agree with Josh, that is just iron deposited from an unfortunate incident. Sand it off, and go to a grit you are happy with, and soak it with something acidic to remove surface iron, a poor man's passivation. You can then polish it if you like. I am sure it is fine. Bill Coleman C 39

Re: Stus-List Wednesday Night racing

Offices 2950 Breckenridge Lane, Suite Nine Louisville, Kentucky 40220-1462 502-584-7255 -Original Message- From: Bill Coleman via CnC-List <cnc-list@cnc-list.com> To: cnc-list <cnc-list@cnc-list.com> Cc: Bill Coleman <colt...@verizon.net> Sent: Mon, Jul 11, 2016 9:02 am

Re: Stus-List Wednesday Night racing

We've been doing if for 18 years, the highlight of our week. Wednesday nite JAM racing literally saved our fleet. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jean-Francois J Rivard via CnC-List Sent: Sunday, July 10, 2016 10:22 PM To:

Re: Stus-List ST4000+ WheelPilot heading Calibration

on where you are in PA. Rick Brass Washington, NC -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Coleman via CnC-List Sent: Saturday, July 09, 2016 3:07 PM To: cnc-list@cnc-list.com Cc: Bill Coleman <colt...@verizon.net> Subject: Stus-List

Re: Stus-List ST4000+ WheelPilot heading Calibration

obably about right, depending on where you are in PA. Rick Brass Washington, NC -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Coleman via CnC-List Sent: Saturday, July 09, 2016 3:07 PM To: cnc-list@cnc-list.com Cc: Bill Coleman <colt...@veriz

Stus-List ST4000+ WheelPilot heading Calibration

I have just done my turns to calibrate my fluxgate, and when I correct it down 10 degrees to agree with my GPS heading shown on my i70 Display, that heading drops 10 degrees. So between the two of them, I am always 10 degrees off. I think I am now around 40 degrees low, by the time I figured what

Re: Stus-List Salon Lighting

Regards, Ron Ron Ricci S/V Patriot C 37+ Bristol, RI <mailto:ron.ri...@1968.usna.com> ron.ri...@1968.usna.com From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Coleman via CnC-List Sent: Friday, June 10, 2016 8:53 AM To: cnc-list@cnc-list.com Cc: Bill

Re: Stus-List Propeller - flexofold

I can say that going from a two blade Max-Prop to a 3 blade Gori I have way less vibration. That is why I did it. If I was not racing I would have gotten a 3 blade Flexofold. The Max Prop seems to have a Chop-Chop sound at certain RPS’s, which I attribute to the flat blades, altho I am no

Re: Stus-List Salon Lighting

that LEDs are better for a directed light source, and fluorescents are better for area lighting. Steve Thomas C MKIII Port Stanley, ON - Original Message - From: Bill Coleman via CnC-List <mailto:cnc-list@cnc-list.com> To: cnc-list@cnc-list.com Cc: Bill Coleman <mailto:

Stus-List Salon Lighting

Most of the older C's had double rectangular fluorescent lights in the main cabin, which are nowadays woefully inadequate. I eventually gave up finding a replacement that would cover all the holes and I purchased 4 Aqua Signal lights,

Re: Stus-List Right of way (ROW) discussion

I would certainly get them the right away, unless I was in an opti. Bill ColemanC 39 Erie Original message From: "Dennis C. via CnC-List" Date: 6/7/2016 8:46 PM (GMT-05:00) To: CnClist Cc: "Dennis C."

Re: Stus-List Splash

Lake Erie has been fabulous for a few weeks.  Just got mine in last week.   Bill Coleman C 39 Erie, PA Original message From: S Thomas via CnC-List Date: 6/3/2016 8:11 PM (GMT-05:00) To: cnc-list@cnc-list.com Cc: S Thomas

Re: Stus-List Older C Bow Navigational lights

It would help if you said how old.  If it is as old as mine,  wing it ,  give it some thought and I am sure you can do better, those were kind of home - made. I mean where they have a green plastic cover screwed to the side ..its not like you are looking for a replacement part for an Olds

Re: Stus-List Rudder collar "donut" removal

If the collar came off, the quadrant would *Probably* keep if from falling through, but if it wasn’t cinched up tight on your shaft, it could slip. The Donut is like the thrust bearing which adjust the height & clearances, and without it the quadrant would be scrubbing on the top of the tube.

Re: Stus-List Rudder collar "donut" removal

Good suggestions, all – As mentioned, make sure all the setscrews are out, in case there were one on top of another. If someone ground a setscrew into the threads, you could be screwed, no pun intended. Stainless on Stainless galls terribly, which is why everyone is always saying to use Tef

Re: Stus-List Autopilot purchase and solar panel install

I know they rate these autopilots by weight, as they have to have something to scale them by, but I think what is more important is how well balanced your rudder is. For instance, if you had a 20 foot catboat with an unbalanced barn door hanging out the back, you could burn up one of those

Re: Stus-List Autopilot purchase and solar panel install

My sentiments exactly. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Richard N. Bush via CnC-List Sent: Wednesday, April 20, 2016 8:00 AM To: cnc-list@cnc-list.com Cc: Richard N. Bush Subject: Re: Stus-List Autopilot

Re: Stus-List "The Weekend Sailor"

Is it not for sale yet? Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of David via CnC-List Sent: Monday, April 18, 2016 5:39 PM To: CNC CNC Cc: David Subject: Stus-List "The Weekend Sailor" The Admiral and will be at the showing in

Re: Stus-List 35-1 refrigeration installed completed

Um, Denise. . .  er, have you had the 'Change'? Bill Coleman  Original message From: "Rochester.rr.com via CnC-List" Date: 4/19/2016 7:22 AM (GMT-05:00) To: cnc-list@cnc-list.com Cc: "Rochester.rr.com" Subject: Re:

Re: Stus-List Preventer

♪, You can check in, but you can never leave . . . ♫ Seriously tho, maybe you should get the digest once a day. Regards, Bill Coleman From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Curtis via CnC-List Sent: Wednesday, April 13, 2016 11:40 AM To:

Re: Stus-List Lake Michigan CnC Rendezvous

Can I get there through the Highland Canal? Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Randy Stafford via CnC-List Sent: Tuesday, April 05, 2016 12:31 PM To: cnc-list@cnc-list.com Cc: randy.staff...@comcast.net Subject: Re: Stus-List

Re: Stus-List LED Nav Lights

/ — Fred Fred Street -- Minneapolis S/V Oceanis (1979 C Landfall 38) -- on the hard in Bayfield, WI :^( On Apr 4, 2016, at 9:18 AM, Bill Coleman via CnC-List <cnc-list@cnc-list.com> wrote: Interesting, well, I am replacing a Perko# 120MD because Perko decided to use plain

Re: Stus-List LED Nav Lights

at is what I have marked on the switch. That is referred to as an All-around white light in the ColRegs. Rick Brass Washington, NC From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Coleman via CnC-List Sent: Saturday, April 02, 2016 8:41 PM To: cnc-list@cnc

Re: Stus-List LED Nav Lights

I need another deck/steaming light  like this, but why do they call it a Masthead light when it is not 360 degrees? Bill Coleman  Original message From: jtsails via CnC-List Date: 4/2/2016 7:28 PM (GMT-05:00) To: cnc-list@cnc-list.com Cc:

Re: Stus-List Headliner plugs

Most any hardware store has them, including Lowe's Home Depot Etc. Some look different though, as some are kind of translucent vs solid white. There used to be a really great local hardware that had a huge selection but unfortunately knocked out by the big boxes. But they had not only the

Re: Stus-List Max prop angle

Wow, you ought  to be able to get up to eight knots with that setup.  Bill Coleman  Original message From: Ken Heaton via CnC-List Date: 3/27/2016 2:46 PM (GMT-05:00) To: cnc-list Cc: Ken Heaton

Re: Stus-List Rolly Tasker Sails

This brings up an interesting story. The local sailmakers get's really irritated when people bring cheap Chinese sails to him to fix. A few years ago, my girlfriend at the time told me a good friend of hers was really bummed, said their sailing season was over because the clew of the

Re: Stus-List Fire blankets, beer & wool

Not sure what you mean by 'Welding Head', but it has a high volume regulator, the typical regulator that would handle welding gasses or pushing beer did not have the volume to handle a ships horn. No dip tube, but I suspect that If I turned it upside down it may come out liquid, I have never

Re: Stus-List Fire blankets

Viola - Joe just gave me a reason to leave my CO2 bottle on the boat - 3 reasons.  1st, (what I got it for ) to blow a big ship horn, 2nd, to push my favorite craft beer , ( I may have to get a large cooler ), and 3rd, put out fires! Bill Coleman  Original message

Re: Stus-List Rudder replacement

Guilty as charged. Maybe Infamously would be more appropriate. I think we tend to feel that we have to fix these boats to factory standards when we get them, but in reality as they get older, they get more customized, which is not a bad thing. I don’t think anyone would want to replace their

Re: Stus-List Irgarol - reply from Interlux

My best guess is, that they switched suppliers. That’s the problem of using a House Brand, they pick the lowest cost provider and keep selling it as their own. They probably offshored it. Pettit is Pettit. Interlux is Interlux. Just my opinion, of course. Bill Coleman C 39 Erie, PA

Re: Stus-List Irgarol

> Bill Bina On 3/14/2016 8:47 AM, Bill Coleman via CnC-List wrote: http://www.totalboatshow.com/wordpress/2015/03/13/antifouling-companies-stru ggle-with-the-loss-of-herbicide-irgarol/ Just in case someone hasn't gotten the whole scoop. Bil

Stus-List Irgarol

http://www.totalboatshow.com/wordpress/2015/03/13/antifouling-companies-struggle-with-the-loss-of-herbicide-irgarol/ Just in case someone hasn’t gotten the whole scoop. Bill Coleman C 39 Erie, PA ___ Email address: CnC-List@cnc-list.com

Re: Stus-List Wiring an inverter

Just a note here, I notice Del City is now handling a lot of Blue Sea inventory. http://www.delcity.net/productsearch?search=blue+sea=0=0=#search=blue %20sea=72 Don't know how their prices compare. Bill Coleman C 39 Erie, PA -Original Message- From: CnC-List

Re: Stus-List Gooseneck fitting

If I am understanding you correctly, I would think you could bore those holes slightly oversize, and squeeze in either a stainless tube bushing, or Nylon of Delrin bushing, which would make a much nicer bearing surface. Bill Coleman C 39 Erie, PA -Original Message- From:

Re: Stus-List filling old screw holes in the cabin ceiling liner

Another alternative are white hole plugs available at hardware’s and Home Depot, etc, Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Bina - gmail via CnC-List Sent: Thursday, March 10, 2016 12:36 PM To: cnc-list@cnc-list.com Cc: Bill

Re: Stus-List Birth of a Mega Putt Putt

A friend of mine was interning in the early 70’s at C, and the Mega was one of his projects. I forwarded to him this post by Stu, and this was his comment below - Cracks me up! Bill Coleman C 39 Erie, PA Subject: Re: Stus-List Birth of a Mega Putt Putt This damn boat will

Re: Stus-List FM antenna?

I have one of those and it works fine. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Chuck Saur via CnC-List Sent: Wednesday, March 02, 2016 6:56 PM To: cnc-list@cnc-list.com Cc: Chuck Saur Subject: Stus-List FM antenna?

Re: Stus-List Window Replacement

I discovered, much to my chagrin, that diesel softens 5200. Also a heated putty knife or wire. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rick Brass via CnC-List Sent: Thursday, March 03, 2016 1:31 PM To:

Re: Stus-List Cushions smell

Another thing that is helpful, is putting it out in the sunlight and breeze. UV light kills lots of spores and other problems Bill Coleman  Original message From: Pete Shelquist via CnC-List Date: 2/25/2016 7:30 PM (GMT-05:00) To:

Re: Stus-List Handicap questions for JAM racers

I see a little difference, but not a lot. And I am not sure where that comes from. I just know that they are still rated kind of high (in JAM), which makes them not as competitive, and they get discouraged. Of course in certain spinnaker races they kick ass. Regards, Bill Coleman

Re: Stus-List Handicap questions for JAM racers

I think the sport boats get screwed in the Jam Races, at least on L Erie, Their overall rating incorporates their sprit, which they get no use from in a JAM, not to mention their small jibs. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List

Re: Stus-List New sail for the roller furler?

I’ve never heard of a marina getting discounted pricing on a sail – is that common? Seems like that would complicate their life, what with adjustments, measurements, etc. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jack Fitzgerald via

Re: Stus-List Sale alert automatic inflatable harness

I thought Sospenders came up with these first, but maybe they were just the first in the USA. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Russ & Melody via CnC-List Sent: Friday, February 19, 2016 12:07 PM To: cnc-list@cnc-list.com Cc:

Re: Stus-List paragon v-drive transmission

One of the times I changed trannies, I had to modify the lever on the tranny. I had to drill a hole closer to the axis, as It didn’t have enough throw to completely engage reverse. This shortened the length you had to move the lever. I have to agree, no one would design a shift wherein you had

Re: Stus-List Stus list Soft shackle

I put some of that white vinyl over my baby stay to get it to pass over.Bill Coleman  Original message From: David Knecht via CnC-List Date: 2/17/2016 8:43 PM (GMT-05:00) To: CnC CnC discussion list Cc: David Knecht

Re: Stus-List Landfall 38 Atkins & Hoyle hatch seals

Measure twice cut once. And yes I do mean half inch, and I think it was a CH more. Or less. Now I'll have to pull that out and measure it again because I know it was around a half an inch, certainly not 3/8. Bill Coleman  Original message From: Dreuge

Re: Stus-List Landfall 38 Atkins & Hoyle hatch seals

I have a roll of 3/8, I could send you some for shipping. I have the larger Atkins Hatch, the cord for that seems to be around 10 mm. I don’t have a roll of that. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Dreuge via

Re: Stus-List Nav Station Panel and Volt Meter Recommendations

I used Starboard with that kind of pebbled finish. Not like your setup, tho. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jake Brodersen via CnC-List Sent: Monday, February 15, 2016 1:30 PM To: cnc-list@cnc-list.com Cc: Jake Brodersen

<    3   4   5   6   7   8   9   10   >