Several have asked what I meant by "Star" radio...
http://www.radcomms.net/PicaStar.html
73! Ken Kopp - K0PP
elecraftcov...@rfwave.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://m
If you look at the schematic of the SignaLink, you'll see that it is redundant
to what is already built into the K3. In addition, the K3 has a stereo audio
out interface, facilitating the use of software for AFSK that recognizes dual
RX for split frequency DX chasing.
http://www.tigertronics.co
Lee
I had an issue with the signalink were somehow the mixer settings got
changed. I called the Signalink folks and they advised the VOL and the
WAV settings should be set to max.
73
Greg
On 6/30/2010 7:08 PM, Lee Buller wrote:
> I went back through the installation of the SignaLink USB agai
After installing the tilt bail and replacing D5 (that I installed backwards)
on the front panel board, my K2 passed all Part 1 tests so now I am on to
Part 2. Thanks to the group and especially Don for all the advice.
Brian
http://home.comcast.net/~b.denley/index.html
- Original Message -
We do live in amazing times. I sent my K3 off to have it repaired and
modified. The work done was excellent by Dale Farmer and the K3 came out of
Aptos with the old serial number but a new radio. The trouble was an encoder
had quit working and that cause half the buttons to quit too. But
I went back through the installation of the SignaLink USB again. I increased
the drive from the computer to the device using the mixer panel program in
Windows XP. It was set as per the instructions, but I tweak it up a couple of
notches and it seems to drive a whole not better now. I get ple
At Field Day on Saturday 26 June, around 1800 local EDT, my K2 #771
took what appears to have been an induced voltage spike from the
connected antenna.
I brought the rig home at 11:30PM and diagnosed the problem, and
replaced two of the three parts that were zapped in the KAT2. My K1
assumed air
Lee,
As far as I know, none of the K3 mods chanded the Line-in on the K3.
Has anything changed on your Signallink or on your computer?
73,
Don W3FPR
Lee Buller wrote:
> Ladies and Gentlemen
>
> I just got my K3 back from Aptos. I had some issues with the unit that were
> repaired and all t
Lee...
I have a fully fleshed-out K3 that I use with a SignaLink USB. The
K3 is about 3 months old and was factory-built. I am running off a Dell
XPS-420 (WIN 7 Ultimate (32 bit)) and FLDIGI 3.12.5 -- with this set-up,
I run the TX pot about 9 O'Clock, the RX pot at noon, and my line level
Yeah, mine's always been like that. There is a jumper in the Signalink
that will make the problem a bit better, but still I have to run with
all the levels set high. It's always worked though and never prevented
me from working plenty of digital contacts with a clean signal...
73,
Dave. AH6T
Ladies and Gentlemen
I just got my K3 back from Aptos. I had some issues with the unit that were
repaired and all the mods were put into place.
Things have changed for my AFSK setup and wonder if others are seeing this.
I am now having to drive the SignaLink USB full TX to get any ALC i
I believe Tripplite bought out Keyspan.
Bill
K9YEQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of K5JAZ
Sent: Wednesday, June 30, 2010 5:27 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K2 and USB to Serial for Ra
I am sure they are working on it...but waiting to make sure that the top teams
(1 - 44) used Elecraft rigs!
73,
Henry - K4TMC
-Original Message-
From: Lu Romero
To: elecraft@mailman.qth.net
Sent: Wed, Jun 30, 2010 5:53 pm
Subject: [Elecraft] Fwd: [FCG] Fwd: [PVRC] Who's t
Please see http://www.tripplite.com/en/support/downloads/ for their Microsoft
Certified driver for this device.
I use this converter daily on my Windows 7 Professional OS with no problems.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K2-and-USB-to-Serial-for-Radio-Contro
Are there ... other than my friend Bill ... users / builders
of the "Star" here on the reflector?
73! Ken Kopp - K0PP
elecraftcov...@rfwave.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecra
Hello Elecraft Principals and Advertising agency...
I think there is an ad somewhere in this message posted by
fellow Elecrafter K2AV...
:)
73
Lu Romero - W4LT (currently portable 9V1 until 7/21)
-
If you want to know what rig is on top these days, can't
think of a more f
On 6/30/2010 4:54 PM, K5JAZ wrote:
> Joe:
>
> I use the Tripplite USB-Serial converter at
> http://www.tripplite.com/en/products/model.cfm?txtModelID=3914 . This
> converter works seemlessly with HRD, TRX-Manager, and Logic8 in my shack. As
> the others have said, do not use a standard serial cabl
Joe:
I use the Tripplite USB-Serial converter at
http://www.tripplite.com/en/products/model.cfm?txtModelID=3914 . This
converter works seemlessly with HRD, TRX-Manager, and Logic8 in my shack. As
the others have said, do not use a standard serial cable to your K2!
--
View this message in contex
Bill,
My bet would be on a poorly tinned toroid lead either on L1 or L2 on the
LPF board.
The red winding is only used on 80 meters, and the relay shorts out the
red winding on the other bands.
Look very carefully at the back of the LPF board - if you see any trace
of red enamel, that is the pr
I installed the KXB3080 option in my KX1 a couple months ago and everything
checked out OK after completion, including output on 80 meters.
Now however, I am getting no output at all on 80 meters. I am still
getting 5 volts output at point F, and current draw of the KX1 increases by
around
After more than 6 years off and on (more off, than on), Elecraft K2/100 s/n
4276 lives!!! The final test was FD 2010 operating from the Uncle Bill's Radio
Club for Kids (UBRCK) field day site, under callsign NJ1E. The rig successfully
logged more than 35+ contacts under the hand of several kids
Tom,
You must have missed the answer to that question that I posted 3 days
ago. I am repeating it here FYI.
"The P3 can indeed be used with the K2, but the K2 needs a buffer
amplifier to isolate the IF output.
Take a look at Jack Smith's Z1B buffer amp at
http://www.cliftonlaboratories.com/c
The Elecraft web site still says "Ships starting 7/15". I'm not sure
how much effort it would take to connect the P3 to the K2. It won't be
simple "plug-in" as it is for the K3 though.
73, Ted, W2ZK
On 6/30/2010 1:02 PM, Tom Boag wrote:
> Haven't heard anything re the P3 lately. Was thinking
Just got my K3 back from Aptos for a complete going through...repair of an
encoder...all the mods...and the new DSP board. I am in the process of pulling
out the manual and learning my K3 all over again.
Lee
k0WA
Ham Radio Operators: Kansas QSO Party is August 28-29, 2010. See
www.ksqsop
Haven't heard anything re the P3 lately. Was thinking about buying for
myself last Christmas but was delayed. I hope that it will be compat
with K2 as well as K3.
73 DE AF6TB, Tom
__
Elecraft mailing list
Home: http://mailman.qth.net/mai
Can you now explain how you use the RX Antenna types... IE. When you push and
hold the RX ant button...
> Date: Wed, 30 Jun 2010 03:40:52 -0700
> From: btipp...@alum.mit.edu
> To: elecraft@mailman.qth.net
> Subject: Re: [Elecraft] How to work KXV3
>
>
>
> lu1xs wrote:
> >
> > I have a modul
All,
Thanks for the leads and advice. I finally selected the K1EL K12-battery
keyer. http://k1el.tripod.com/K12.html for a modest $17.
From the datasheet, it appears to have not only ultimatic, but
dah-override. When I get it built, I'll find out for sure how it'll work
for me.
Stay tuned ...
You should take a look at N4YG keyer. I have two, for a K3 and a K2 and
they work great, both from the keyboard and from paddles. I think from
the paddles, this keyer will do what you want. I don't use the radio
internal keyers at all. Both radios work just great. I think the keyer
options in th
Hi Eric
It was good to have the opportunity to say a brief hello on Friday.
Thank you for making the long trip, and hope you eventually recovered
from the journey(s) and jet-lag.
73 Peter G3XJS (K2 # 573)
__
Elecraft mailing list
Ho
lu1xs wrote:
>
> I have a module installed (KXV3) my K3, please I need a help to better
> understand the work of this module, when using an antenna to receive RX
> ANT IN (KXV3) rear panel, and to transmit ANT 1, the change is done
> automatically or I have to do manual with Knob Controls RX ANT
30 matches
Mail list logo
