Yes I can set it at 35 watts which is what I usually use to drive the KPA 500,
and speak in the mic for ssb and get no power out. In cw at the same 35 watts,
when I send code either straight key or padfle. 0 watts out. Same results if I
attempt to run bearfoot at 100 watts or 5 watts, I get no
Elecraft service set my Tune Pwr to 5.1 watts to prevent ‘inadvertent running
of TX gain calibration’.
Have you tried running the TX gain calibration with the K3 Utility?
-- Mike Flowers, K6MKF, NCDXC - "It's about DX!"
> On Aug 14, 2018, at 5:31 PM, Dennis Moore wrote:
>
> "No power to
"No power to tune anything." Does this mean you've only tried to tune,
and haven't tried actually transmitting cw or phone? If so, and I don't
know how it would have changed, have you checked the Menu-Config-TUN PWR
to see what it is set to? If it is set to .1 it will show 0.0
73, Dennis NJ6G
oops ! my serial port was denying access.. MY BAD
using p3 utility 1.16.3.15..
have MCU 1.59 svga 1.33
and
when I check available I get 1.54 & 1.25
"""
P3 MCU revision 01.59. RS-232 speed 38400 bit/s.
20:15:43 Opening connection to ftp.elecraft.com
20:15:43 Copying
I have enjoyed the wisdom of this group and have learned so much but now it is
my time to ask for help. My K3 is showing no power out. I have the K line. The
relay clicks when going from 11 to 12 watts. I can set the power up to 110, but
when I hit tune I get zere watts shown and verified by my
using p3 utility 1.16.3.15..
have MCU 1.59 svga 1.33
and
when I check available I get 1.54 & 1.25
"""
P3 MCU revision 01.59. RS-232 speed 38400 bit/s.
20:15:43 Opening connection to ftp.elecraft.com
20:15:43 Copying files to C:\Program Files (x86)\Elecraft\P3 Utility
20:15:43
Would a CI-V cable work for you? I personally tested IC7600 and 7300 and I’ve
been told that 7610 also works. The amp looks for the TX frequency message from
the exciter. I’m not sure whether a 765 pro 2 sends that. If it doesn’t, I can
teach KPA1500 firmware to look for the frequency message
Good day group I am wondering is there a way to change bandson my KPA 1500 by
selecting the band on my ICom 756 Pro 2. I have no issueswith the changing
bands via a Rf burst. But I would really like it to change bands but selecting
the correct band from my radio.
Thanks you in advance
Does Heil have the settings on their website? I seem to recall they do. That
is a good place to start.
Bob, K4TAX
Sent from my iPhone
> On Aug 14, 2018, at 1:58 PM, Thomas Donohue wrote:
>
> I recently purchased subject mic and will be connecting it to the K3S
> shortly. Before I do
I recently purchased subject mic and will be connecting it to the K3S shortly.
Before I do that, I was wondering what mic settings to use? I currently have a
Heil PR-10 mic and am using the MIC FP HI menu setting and a mic gain of 20;
the PR-10 works fine, but I wanted to get a mic that I could
Posted on behalf of owner by Warren Merkel, KD4Z.
K3 Serial # 0632
Factory Assembled. Original owner, non-smoker, climate-controlled
environment.
Updated with the current firmware revision.
Includes original, Elecraft bound manuals (construction and operating),
power cable, and optional hand
Thanks for your patience, Eric. (:-))
73 all
K0PP
On Tue, Aug 14, 2018, 10:05 Eric Swartz - WA6HHQ, Elecraft <
e...@elecraft.com> wrote:
> We're drifting a little too OT. Let's close this thread in the interest of
> reducing email overload for our readers.
>
> 73,
> Eric
> Moderator etc.
>
We're drifting a little too OT. Let's close this thread in the interest of
reducing email overload for our readers.
73,
Eric
Moderator etc.
/elecraft.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
My solution is very simple. I ignore all calls unless they appear on
my caller ID from my contact list. Likewise on e-mail, my spam filter
gets 99.9% of all of them and they end being sent to the junk folder.
That folder gets emptied every 12 hrs. The one or two that get through,
also
I use commercial spam solutions for relief from internet email spammers. Lots
of them out there. That's all well and good. The REAL problem for me are robo
calls to my home phones and cell phone. I listed both phones on the State of
Missouri and the Federal *No Call Lists* years ago. That
Got it. I had only looked under Elecraft. Thanks!
73, Jim N7US
-Original Message-
Hi Jim
Look under Elecraft or KPA500.
My KPA500 program is there in add/remove.
Mike va3mw
On Tue, Aug 14, 2018 at 8:55 AM, Jim N7US wrote:
> How can I uninstall the KPA500 and KAT500 Remote
Hi Jim
Look under Elecraft or KPA500.
My KPA500 program is there in add/remove.
Mike va3mw
On Tue, Aug 14, 2018 at 8:55 AM, Jim N7US wrote:
> How can I uninstall the KPA500 and KAT500 Remote programs? I don't see
> them
> listed in Device Manager's Programs and Features.
>
>
>
> 73, Jim
How can I uninstall the KPA500 and KAT500 Remote programs? I don't see them
listed in Device Manager's Programs and Features.
73, Jim N7US
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Hello Stefan,
I remember running into some roadblock in doing this, but I don't
remember what it was now... I initially wanted to connect directly to
the K3 as well. I think it was if you had a P3 SVGA, it worked better.
If you get things running on just the K3 send me the info, and I'll add
I did get one reply on this topic. Dave NK7Z has already documented nicely on
his website how to connect a Genovation keypad to the P3. The question was how
to connect it directly to the K3/K3S, if possible at all, in order to free the
P3’s USB-port.
A pre-Genovation "button box" was hooked
Hi all
I am trying to upgrade a P3 MCU 1.29 to 1.54 and\or 1.60 (No SVGA option
installed).
When I hit send checked items to P3 the relays click every 2 seconds and
I see 2 messages repeat forever:
1. Attempting to connect P3 on port COM1 at 38400 bit/s in the P3s
utility window,
2.
21 matches
Mail list logo
