While N connectors do have some design and impedance advantages, some of us
that have lived in extremely cold climates... have seen the center pins pull
out of N connectors due to thermal contraction of the center conductor over
distance. A UHF or DIN connector will usually not do that.
Dr.
So are you saying that the KPA500 is a bad design?
I'm not aware of a single non-CB amplifier that doesn't use an input pad...
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
Owner - Operator
Villa Grand
Well you might consider this. I do a lot of DXing from J6. Typically the
pile-ups are hundreds if not more people calling once it gets going. That 1
s-unit difference can mean the difference between working the DX or the band
going out before you do. It's personal, right? Kinda of reminds me
I have three. I built an electronic switch to automagically switch the
lines basis the band output. Video switch ICs.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
Owner - Operator
Villa Grand Piton -
The question of Elecraft building1500 watt amps has been settled, but there are
those of us that can build pretty much whatever we want... and that includes
me. I currently have a twin BLF188XR amp nearing completion on my lab bench,
and my issue has always been making it look like the
One of the guys at Elecraft (Mike?) did this with a cheap switch box available
off Amazon. I took that box and added some video analog switches and a band
decoder to do it automagically and basis power level. Its a simple matter to
do. Just get creative.
Dr. William J. Schmidt - K9HZ J68HZ
I use the HA400 for contesting too. Its perfect for s several pairs of
headphones and lets everyone have their own gain control.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa
I would buy a 736R updated replacement in a microsecond Specially with some
of the capabilities of the K3. I sold my 736R and have regretted it ever since.
(I have no interest in QRP/ being weak).
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner -
Son of a bitch.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it: www.VillaGrandPiton.com
email: b...@wjschmidt.com
> On Dec
t.com]
Sent: Wednesday, December 16, 2015 7:51 PM
To: elecraft@mailman.qth.net
Cc: Dr. William J. Schmidt, II <b...@wjschmidt.com>
Subject: Re: [Elecraft] KIO3B
Hi Bill (and everyone else interested in the KIO3B upgrade),
Unfortunately pulling the KIO3B boards out of a packaged K3S kit or
the KIO3B is available.
>
> Ed W0YK
>
>
>
> -Original Message-
> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dr.
> William J. Schmidt, II
> Sent: 17 December, 2015 06:18
> To: 'Eric Swartz - WA6HHQ, Elecraft'
> Cc:
I feel a bit responsible for this thread and it needs to end. The issue for me
is that my radio is at my place on J6 where my electronics lab is not. I have
three options: 1. Bring the radio back and fix it, 2. Try to fix it down there
(with very minimal resources), or 3. Bring a new part down
Running out of days in 2015...
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch K9ZC
Staunton, Illinois
Owner Operator
Villa Grand Piton J68HZ
Soufriere, St. Lucia W.I.
Rent it: www.VillaGrandPiton.com
email:
is
> strong and therefore Elecraft. ;>)
>
> Ed W0YK
>
> -----Original Message-
> From: Dr. William J. Schmidt, II [mailto:b...@wjschmidt.com]
> Sent: 15 December, 2015 16:21
> To: e...@w0yk.com; 'ab2tc'
> Cc: elecraft@mailman.qth.net
> Subject: RE: [Elec
How much money do you want to spend?
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it: www.VillaGrandPiton.com
email:
Interesting. My SP3 showed up with a busted off switch on the front. I
wonder where the quality control has gone?
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
Owner - Operator
Villa Grand Piton -
It has happened to me as well.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it: www.VillaGrandPiton.com
email:
Yeah I'd like to know too. My KIO3 was busted from the factory (line input
doesn't work)... If I'm gonna replace it, it might as well be with the new
KIO3B
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
I just received a new MicroKeyer II and the rear cable attachment kit for
using with my K3. I plan on using it at my DX station J68HZ. I don't have
any experience with these microHAM boxes. I have always used the SignalLink
USB box for RTTY. Without spending 3 days researching the connection
I have two of each. What do you want to know?
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
Owner - Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it: www.VillaGrandPiton.com
email:
Call Bob's wife Sarah or service manager Donna at 618-257-3000 and ask them for
the part. It can still go out today.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton -
To: elecraft@mailman.qth.net; elecraft...@yahoogroups.com
Subject: [Elecraft] Multiple sensors with P3 transmit monitor
On 07/25/2015 07:11 PM, Alan Bloom wrote:
On 07/25/2015 01:01 PM, Dr. William J. Schmidt, II wrote:
I suppose the next thing we'll need is an outboard box to switch 3 P3TX
The difference, of course is, that the Steppir controller just listens.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it:
Interesting. I wondered how this worked. My P3TXMON was shipped this week so
ill get to play with it soon, but one would think the scale would be adjustable
so that whatever power is seen, you could make that the full scale. This is
just a scaling issue. Otherwise running the KPA500 with the
I suppose the next thing we'll need is an outboard box to switch 3 P3TX
sensors automatically keyed off the ACC connector (amp off HF, amp on HF, 2
meter). H. I wonder if anyone else has thought about this?
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
I use a Superantennas YP3 with my own modeled tunings and some refinements
(new set of coils and full sized elements on 12 meters too). 30-160 I just
use dipoles. rolls of wire pre-cut with dog-leash clips on the end that snap
onto a balun and alligator clips on the balun wire leads for
.
Funny thing is though, although I'm a pretty active DXer, I've only worked
J68HZ
once. Three years ago on 20M RTTY.
On 7/21/2015 5:54 PM, David Gilbert wrote:
As they say, your callsign alone is probably worth 20db.
;)
Dave AB7E
On 7/21/2015 5:24 PM, Dr. William J. Schmidt, II wrote
://observer.wunderwood.org/ (my blog)
On Jul 20, 2015, at 1:53 AM, Dr. William J. Schmidt, II b...@wjschmidt.com
wrote:
Yes you can use it one of two ways... in TCP mode, there is a small driver
loaded on your PC that creates a pseudo RS232 port on the computer that all
your existing software
, Pierfrancesco Caci p...@tippete.net wrote:
On 20 July 2015 07:53:04 CEST, Dr. William J. Schmidt, II
b...@wjschmidt.com wrote:
Yes you can use it one of two ways... in TCP mode, there is a small
driver loaded on your PC that creates a pseudo RS232 port on the
computer that all your existing
I have a prototype Ethernet interface running inside my K3 right now...
simple replacement for the KIO3 board. I posted a couple of times
suggesting it but was completely ignored so I build my own. It's just a pic
with Ethernet capabilities and replaces the functions of the KIO3 completely
and
Ethernet Interface
On 19 July 2015 23:40:51 CEST, Dr. William J. Schmidt, II
b...@wjschmidt.com wrote:
I have a prototype Ethernet interface running inside my K3 right now...
simple replacement for the KIO3 board. I posted a couple of times
suggesting it but was completely ignored so I build my own
Yes 50dB is about 30dB too high... Simple modelling says it all...
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
Owner - Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it:
Interesting. Ive had a similar issue with N1MM and my K3. Every once in a while
it will add 0.2 KC to the main frequency. Its always been + and I've not been
able to figure out why it happens.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big
You actually need more than one datapoint in most cases to identify the correct
part. Simply measuring the reactance with a nice antenna analyzer at several
frequencies (a few loops of wire through the device) and matching that up with
the theoreticals given in the data sheets will tell you
Wayne should be able to tell you the font point reduction for the S.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton - J68HZ
Soufriere, St. Lucia W.I.
Rent it:
I have to scratch my head every time the issue of what antenna should I use
for bla bla situation comes up on any reflector. It's similar to the
question of what radio should I use for X situation. When asked, the
responses are mostly personal (as is evident by all the comments from using
There is probably some middle ground here to satisfy most people in this
situation. It's completely understandable and correct that Elecraft would
not want to spend the effort to re-engineer this board. However some of us
on channel don't see the task as rocket science and in most cases would be
Well let's be clear here...
These are roofing filters, so you will only notice a difference in adjacent
frequency rejection of loud signals... so if you live out in the country and
don't have any loud stations near you, it’s not likely you will ever perceive a
difference between 5 pole and 8
No problem. I do it all the time. Just expect it to be searched and have your
papers granting permission to bring your equipment in handy. You may need them
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Never been asked to power my radio on in at least 25 Caribbean trips.
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton
Soufriere, St. Lucia W.I.
Rent it at:
Contact me off-line. I can tell you everything you want to know about
operating in the Caribbean...
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch – K9ZC
Staunton, Illinois
Owner – Operator
Villa Grand Piton
Soufriere, St. Lucia
You should read this first:
http://www.heilsound.com/amateur/dsp-settings/125-all-things-elecraft
Dr. William J. Schmidt - K9HZ-J68HZ-8P6HK-ZF2HZ-PJ4/K9HZ-VP5/K9HZ-PJ2/K9HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From:
I did it. It works fine.
Dr. William J. Schmidt - K9HZ-J68HZ-8P6HK-ZF2HZ-PJ4/K9HZ-VP5/K9HZ-PJ2/K9HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Guy
Olinger
Put your finger on the end of the INPUT cable and transmit. See if you get
hum. I found that the chokes on my input lines are bad... dunno why but
evidently some radios have bad chokes.
Dr. William J. Schmidt - K9HZ-J68HZ-8P6HK-ZF2HZ-PJ4/K9HZ-VP5/K9HZ
Owner - Operator
Big Signal Ranch
It's called a Tower Jack...
Dr. William J. Schmidt - K9HZ-J68HZ-8P6HK-ZF2HZ-PJ4/K9HZ-VP5/K9HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Joe
K2UF
Sent:
Much cheaper version/ copy on eBay... search!
Dr. William J. Schmidt - K9HZ-J68HZ-8P6HK-ZF2HZ-PJ4/K9HZ-VP5/K9HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
Does Elecraft make antennas now?
Dr. William J. Schmidt - K9HZ-J68HZ-8P6HK-ZF2HZ-PJ4/K9HZ-VP5/K9HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of WILLIS
COOKE
Have you ever listened to the interviews of the Indy car drivers after a
race? Do they say: I wish I had a less powerful engine to make it a more
challenging race.?
I'm on the DX end a lot these days, and I always find myself stopping a
pileup to ask if there are any 10 watt or less stations
That's what I use... about 103 feet... and gives reasonable match on all
bands.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ/ VP5HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: Elecraft
Been done before... search the archives...
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jim
Miller
Sent:
Interesting... I went through this a few years ago trying to develop a set
of headphones that I could use wirelessly to work in my electronics lab yet
still talk on the radio. What I landed on is something interesting made by
Jabra... model #A210... it's a transceiver that can be plugged into the
Well I have something odd going on. I was trying some new antenna tunings
today and noticed that the power out on the KPA500 would start at about 100
watts.ramp up to 500+ watts over about 10 seconds, and then drop back to 100
watts again. It kept repeating this cycle as I was talking to someone
There are additional aspects of these comparisons that are not often discussed.
The ergonomics of the two radios are vastly different... and rightly so given
their history. The Icom has had many more generations of radios to improve the
look, feel and operation of the radio. After owning and
So the conclusion is... have a plan: think the usage of the filters
through... install them once and be happy.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ/ VP5HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From:
Have a look at the MiniVNA Pro. Read the reviews on Eham. Cheaper than
most and small enough to carry up the tower and use with and Android phone.
http://miniradiosolutions.com/minivna
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
Am I reading this correctly? You are driving an AL80B with the KXPA100
being driven by the KX3? That's quite imaginative if that's correct. The
SWR fault is coming from the AL80B input circuit not your antenna (the KXPA
can't see the SWR on the other side of the AL80B). probably something bad
Done. You can buy them here:
http://www.communication-concepts.com/index.php/splitter-combiners.html
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From:
I use the same system but direct connected to the internet. Never once had
an issue with it while running the K3/KPA500...
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From:
Well last night while chasing some DX I experienced the same mysterious
antenna tuning behavior that others have reported with the KAT500 where the
tuner just takes off. I had this happen on 40 meters while working 40
meters over xmas down on PJ4 and saw the KPA500 amp emit a nice thick cloud
of
to prevent auto mode
from an inadvertant start up.
Some have never had this problem with their K-Line, so since the problem is
not universal, it will be much harder to fix.
Toby K4NH
- Original Message -
From: Dr. William J. Schmidt, II b...@wjschmidt.com
To: elecraft
I think the only thing you will get agreement on as far as developments here
is that all the hams will want free hats at Dayton (except me... I've got
one!).
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email:
I take it everyone has good station RF ground systems in the shack (or where
ever the tuner is located)?
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From:
I came to the same conclusion and built filters to clear this up too... but
then...
I'm down on PJ4 for holiday the past two weeks operating for fun with a
portable 3 element beam (20-6) and dipoles for 80 and 40. On Saturday night
I was on 40 meters with the amp running at probably 1.4:1 SWR
Well mine sure didn't go into bypass...lots of thick black smoke and it
thought everything was just fine/ good to go...as I was running for the fire
extinguisher. It confused the heck out of me because the swr was well below
2:1 (like 1.4:1) and I was well within power limits on CW. The good
I tried it... works fine. You can buy adequate input and output combiners
from Communication Concepts.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From:
IS there a way to shut off the out of band transmit limits in the K3? I'm
down in the Caribbean trying to fine tune my antennas and it's impossible to
do with the limiter in place.
[Nb. Yeah I'm sure some smart guy on frequency will say fly home and get my
autek bridge.]
Dr. William
Which products do you use? I use their 60 watt panel.
What is needed to prevent overcharge. Nothing. I don't use a battery.
What does less than full sun do to the capacity. Full sun for full output
is a fallacy. Even 50% sun through overcast gives full output. Buy a
bigger panel, bigger
Interesting. I'm usually the guy saying or teaching the theoretical read
it in a paper side and everyone else is giving me feedback about what
they've actually tried. Not so this time.
Remember the guy asked me what I do... and you did cut off the last sentence
that says I use this with a KX3
Here is a test showing the old versions of solar panels vs. the better
PowerFilm flex panels that I use. thanks to Pat ai4w for pointing this video
out to me.
http://www.youtube.com/watch?v=flvkYi753Js
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big
I use these solar panels for portable operation. They are at Dayton every
year and sell their blemished military panels to Hams.
http://www.powerfilmsolar.com/products/?foldable_solar_panelsshow=category;
productCategoryID=6579productCategoryIDs=6578,6579
Dr. William J. Schmidt - K9HZ /
So far I've counted 96 posts on soldering connectors onto coax. Really?
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
Not that we have established the notes... maybe we can make it play Smoke
on the water?
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
Why don't you try it first with a piece of wire where the vertical would be.
You can run it up the center of plastic conduit or support it with a horizontal
rope. Pretty cheap way to test things out.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ
Owner - Operator
Big Signal
I have a different opinion on buying used heliax. Unless you scan it (TDR
minimum) you will never know if what you are purchasing is a piece of good
used heliax... or something hit by lightning now has carbon track shorts
and/or dielectric that is saturated with water. While some lucky people
I have that flag pole and use the KAT500 to tune it. I've used several
other tuners in the past too, mostly old remote military models. Power
offers no issues... if the antenna tunes at 5 or 100 watts, it will tune at
500 watts.
One thing I always do (at least I've learned something important
I use the Samlex exclusively because I do a lot of island jumping and need
something small and light. I've had mine on several islands, made tens of
thousands of contacts with it in heat and odd voltages. Just keeps ticking.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ
Owner -
Your point is well taken and I support your direction. There is another
avenue as well... some of us are well capable of making updates to the radio
on our own (as you have seen with recent discussion of Mods). It wouldn't
be out of the realm of possibility to see a spin-off group (of us eager
Is this the Cobweb reflector now?
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
This sounds like a lack of creative thinking. How about using two 90 degree
BNC elbows on the back of the radio and a couple of BNC jumpers. You can
put the preamp anywhere... even in the next room is that is your fancy.
Also, you might try one of the 50+ preamps that are already available by a
H... I fix my own stuff, so my expectation is that a diagram show up
with my newly purchased KPA500. My policy is that if I don't get a diagram
with the electronics and I have to fix it, I reverse engineer it and make
it public to everyone. If I get one, I keep it to myself. Pay me now or
Ah yes... the elusive 6000 series vapor-flexes...
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net]
You can just use heliax. Works perfect.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf
Really? Sent me the money and I'll order whatever you want for you...
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
A side note for those attending Dayton. There has been a company that
manufactures solar panels for the government at Dayton the last couple of
years. They sell blemished panels that are used as panels in tents for
power that would work perfectly for the KX3. I've got two of them and use
them
Has anyone used a Bluetooth to RS232 Serial adapter, such as the dongle
style that could plug into a 9-pin connector (but, it does not have to be
dongle style).
No, but I use a blue-tooth connected headset and it works great for moving
about the shack whilst chatting (VOX on)!
Dr. William J.
It works far better to simply call him. He almost always answers.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
Well at least you audio input line works. Mine doesn't...
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
An even better methodology for determining if the power, antenna, and
propagation is good for the type of operating you do is to use the wealth of
internet-connected receivers around the world to see how your signal
compares to other signals received in that particular geographical area.
At the K9ZC station, we have antennas and feed line that are more than 2,000
feet from the shack. I used surplus (new) 1 5/8 feed line for the RF and
direct bury fiber optic cable with converters for the control signals.
Works like a charm.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/
Let me say this more clearly so there is no misunderstanding... you only use
one of these per load center. So for example, I have three 200 Amp load
centers in my house with 40 breakers each (600 amp feed to the house). I
use one of these per load center, for a total of three. It cost me a
Well Antenna theory and operation, like the rest of physics, always hold
true (nuclear blasts don't count)... so the more radiating surface (wire
length or tubing surface) you can get in the air... the better. There is
also a convenience factor, meaning whatever it is needs to tune for the band
This sounds good on the surface, but has the potential to be a disaster.
New end-of-spool heliax is fine. BUT...Avoid used heliax like the plague
unless you have the equipment to scan it (like a good Time Domain
Reflectometer). The longer the heliax is on the tower, the higher the
percentage
Seriously? Asking the Elecraft reflector if the K3 is a fun radio to
operate is like asking drug addicted people if they like drugs.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: mailto:b...@wjschmidt.com
Again, Sam, K9SD has made these for years for several different radios. I
have one for my 781 and I spoke with him before Christmas about one for my
K3. He has a new email address. Anyone can contact me via email for it (I
don't want to publish it on the reflector).
Dr. William J. Schmidt -
Mine does the same thing except only when the PR6 (six meter preamp with the
ON control jumper in the correct position for the K3) control is plugged
into the ACC jack. I surmise that that possibly D4 (the diode that was
added for the reported MOD:
My wish is for an Ethernet connection. I'm actually working on a retrofit
to my radio right now using an embedded solution, but it could easily be
build into the I/O board. I'll share it when I'm done.
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ J68HZ
Owner - Operator
Big Signal
K9SD already makes this device...
Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
Owner - Operator
Big Signal Ranch
Staunton, Illinois
email: b...@wjschmidt.com
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill
inside the DE15 connector - maybe something is shorting
pin 8 to ground inside there.
73,
~iain / N6ML
On Mon, Dec 31, 2012 at 1:49 PM, Dr. William J. Schmidt, II
b...@wjschmidt.com wrote:
Yes, it works fine with the preamp completely removed...
Dr. William J. Schmidt - K9HZ / J68HZ
So I connected my PR6 - 6 meter preamp to my K3 for the first time last week
and work some DX. At the end of the day I go to shut the radio off and the
display goes blank (hear the relays disengage) but all of the LEDs are still
lit on the radio. and it will not turn back on except to cycle the
, 2012 at 12:20 PM, Dr. William J. Schmidt, II
b...@wjschmidt.com wrote:
So I connected my PR6 - 6 meter preamp to my K3 for the first time
last week and work some DX. At the end of the day I go to shut the
radio off and the display goes blank (hear the relays disengage) but
all of the LEDs
1 - 100 of 133 matches
Mail list logo