As a cw operator I rarely use ssb but few days agò I made a local qsl and I
reduced power to about 30W, more than enough to be heard. When I set up the
power again to 100W the output power was about 50W and wont rise till I
switched to cw sent a dit and switch to phone again.
It happened with
been released but actually i didn't noted
if it happened with previous firmware releases.
Max IW0GXY
-
http://www.iw0gxy.it
--
View this message in context:
http://n2.nabble.com/Hi-cur-on-6-meter-tp2964341p2964341.html
Sent from the [K3] mailing list archive at Nabble.com
I checked and the ammeter read 24A on 6...@100w and 18A on other bands. So
it's an unusual current drain.
Any hints?
-
http://www.iw0gxy.it
--
View this message in context:
http://n2.nabble.com/Hi-cur-on-6-meter-tp2964341p2964363.html
Sent from the [K3] mailing list archive at Nabble.com.
gain is
about 6dBm.
Max IW0GXY
-
http://www.iw0gxy.it
--
View this message in context:
http://n2.nabble.com/K3-10-meter-sensitivity-tp1658620p2119019.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
Elecraft mailing list
Post
Max iw0gxy wrote:
I've tested my K3 MDS today using XG2 and the procedures reported on its
manual.
I've got an MDS of -126dBm pre OFF and -132 dbm with Pre ON. This on 20
meters
the s+n/n ratio with PRE ON is 25dBm,
On 40mt i've got -124 and -127 and a s+n/n of 20
I've no rf
scheduled a test to a
friend's house to make more accurate testing. I wish i would have better
result.
Max IW0GXY
http://www.iw0gxy.it
--
View this message in context:
http://n2.nabble.com/Low-MDS-on-my-K3-tp2107698p2107698.html
Sent from the Elecraft mailing list archive at Nabble.com
but at last I noted that it wasn't fully inserted. I pushed it firmly and
now is working fine.
Ciao
Max IW0GXY
Chuck - AE4CW wrote:
I am seeing an approx. 20% reduction of peak SSB power after pressing ATU
TUNE. This occurs at both 50 and 100 watts into a high-quality dummy load
.
I'll let the list know.
Max IW0GXY
Vic K2VCO wrote:
max iw0gxy wrote:
Hi all,
I connected the XG2 signal generator to my K3 and I've injected 50microV
into the antenna. I have the standard S9 but when I rise the power to 13
and
up signal drop down to S8. If I turn the knob to 12W
but to be sure I've used my
signal generator.
Did someone noted the same behavior?
Max IW0GXY
--
View this message in context:
http://www.nabble.com/K3---Sensibility-drop-when-Hi-Pwr-tp18165707p18165707.html
Sent from the Elecraft mailing list archive at Nabble.com
but to be sure I've used my
signal generator.
Did someone noted the same behavior?
Max IW0GXY
--
View this message in context:
http://www.nabble.com/K3---Sensitivity-drop-between-Low-and-Hi-power-tp18165769p18165769.html
Sent from the Elecraft mailing list archive at Nabble.com
Max iw0gxy
--
View this message in context:
http://www.nabble.com/K3-100-kit-building-slide-show---Italian-tp18129395p18129395.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
That's sound good.
Seems orders are speeding up. From 5 months to almost 4.
Enjoy build it up
73, Max IW0GXY
www.iw0gxy.it
Jeff Maass wrote:
K3/100 (Kit), s/n 1152
Ordered: 2/7/08
Katiegram: 6/19/08
Delivered: 6/25/08 (4 months 2 weeks)
Backordered: KRX3 2nd RX (and three
I've added a translation in english too. Click on the US flag
I apologize for my english but I wish I was clear enough :)
Max IW0GXY
max iw0gxy wrote:
Hi all,
I've posted on my web site http://www.iw0gxy.it/k3_-_assemblaggio.html
www.iw0gxy.it a slideshow of my k3 buildig
tomorrow.
Suggestion?
Max IW0GXY
--
View this message in context:
http://www.nabble.com/full-power-strange-behaviour-tp18139829p18139829.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
Elecraft mailing list
Post to: Elecraft
(the KPA100 is not installed yet).
I checked on the reflector but I'm waiting for the official reply. I wish
I should not send back any board.
Max IW0GXY
http://www.iw0gxy.it www.iw0gxy.it
Paul Franson-2 wrote:
1114 arrived Friday - all went well until I got to the
synthesizer
calibration
and the calibration has finally ended without any
error.
I want to thanks Mike AJ9C for his right intuition about the problem.
I wish this could help someone else
Max IW0GXY
max iw0gxy wrote:
I have almost the same probs on 1118 but mine showed during the synth.
calibration the following errors:
first
16 matches
Mail list logo