I was a Navy-Marine Corps MARS member, then that branch was absorbed
into Army MARS. While with Army MARS, I used my KX3 and KXPA100 out of
the ham bands everyday of the week for net ops.
The rig can be unlocked for out of band transmitusing software supplied
by Elecraft. If I remember
WARNING: LESS-THAN-POSITIVE RESPONSE BELOW
I don't know... With three tattoos, two full beards and a man-bun on their
page, I don't quite think I'm in their target demographic.
I think their thing is simply equalizing the frequency response of each ear,
no? Just use the RX EQ on your K3.
Al
I think the demographic they are shooting for is likely the folks who see
friends paying $300 for super fancy headphones, and can't spend that kind
of money... maybe those folks look different than you do... I know they
don't look much like me.
I do think they are quite interesting and I believe
Ron -
Thanks for the clarification. I had missed that the headphones are actually
matched once you get them, and that can be re-done as needed. I think that
really makes them attractive.
I am going to share the link with locals, some of whom are not happy with
what they are now using.
I agree,
We've just completed our "What would you do with a KX2?" joint contest with
K6UDA. Here are the winning videos that won a KX2. Pretty cool!
See:
https://youtu.be/xlDQu9GbbbY
73,
Eric
/elecraft.com/
__
Elecraft mailing list
Home:
I have the K3s feeding JUMA PA1000 with 8...10W.
It is all OK here, we do not have the 15dB rule.
Using IPA is to prevent 100W PA additional distorsion.
Old QST Review gave only 25 dB for IPA 3rd order IMD.
What might be IMD in present-day K3s IPA ?
Any measures available?
Benny OH9NB
Never mind …
Apparently it was just some garbage in VFO A. VFO B was on 144.00 where it
should have been. A swap and copy of VFOs fixed the problem.
> On Feb 3, 2017, at 3:37 PM, GRANT YOUNGMAN wrote:
>
> Before I call tech support, thought I’d try here.
>
> Just
Before I call tech support, thought I’d try here.
Just installed in the 2M module in my KX3. I’m on the latest firmware rev.
Gone over the setup instructions several times, and the parameters are all set
properly — enabled, 50 Mhz IF, in the band map, etc.
When I go to the 2M band, the
Yes, several times. Just looks like a minor glitch. See my note below.
Thanks … Grant NQ5T
> On Feb 3, 2017, at 3:51 PM, GRANT YOUNGMAN wrote:
>
> Never mind …
>
> Apparently it was just some garbage in VFO A. VFO B was on 144.00 where it
> should have been. A swap
The demo is just a demo. According to the web site, the phones come equipped
to repeat that process to acoustically match the specific earphones to your
ears and apparently can be repeated as needed.
It appears to match the audio level at eight different frequencies to each
ear. Like many, my
Have you shut down the radio and restarted it?
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KX3-2M-module-install-HELP-tp7626439p7626442.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
I used my KX3 on Army MARS without incident. Had no problems with MARS ALE or
any of their digital modes (M110A).
But I left due to family health issues.
all you have to do a supplier Mars call sign to Ella craft and they will send
you the proper software to unlock frequencies - executable runs
I'm looking into possibly getting involved in MARS. The guy that runs it
locally sent the following question about the KX3:
Can the Elecraft KX3 be opened to permit full operation from 1.8mHz to
29. mHz and do they have installed TCXO (0.5%) frequency stability or
the ability to install the
From the manual:
Frequency Stability: +/- 1 ppm typical over 0-50 C. An extended temperature
compenstation procedure can be applied for improved stability (refer to our KX3
web page).
So for operation above 20 MHz, you need to do the extended temp compensation. I
assume they don’t require
If you're ever wondering about the tuning range of an ATU, check out the
blog of K6JCA:
http://k6jca.blogspot.com/
Jeff has done a really thorough analysis of the KAT500, among others,
and plotted the entire range it is capable of matching on a Smith
chart. The plots show not only the
It probably would help to describe your antenna(s).
John KK9A
Dale Martin kg5u said:
I've been operating my new K3S for about 2 months now and love it.
Last week, however, something unexpected happened: as soon as I keyed the
paddles or hit f1 to key the radio (CW), the radio went keydown.
South Atlantic Anomaly.
On 2/1/2017 6:53 PM, Gary Hawkins wrote:
I see the same issue with my KX3. However, since it goes away after a
couple of seconds I've got use to it. Anyone have ideas on the cause?
73's Gary K6YOA
On 2/1/2017 4:25 PM, elecraft-requ...@mailman.qth.net wrote:
Many problems with 'RF in the shack' are caused by bad shield
connections in PL259 plugs. It is also very typical for such problems to
appear suddenly or intermittently.
So if the problem persists when the K3S is connected only to a dummy
load, change the coax patch lead as well.
73 from Ian
This is my first time posting to this group. I'm hoping to own my first KX3
in a week or so. I'm picking up a used 2013 KX3.
Is there anything I should look for to update HW wise when I recieve it.
The current owner has said it has the latest FW.
Looking forward to being an active QRPer with this
Congrats to the winners
73, de Bill, N3JIX
On Fri, Feb 3, 2017 at 4:23 PM Eric Swartz - WA6HHQ, Elecraft <
e...@elecraft.com> wrote:
> We've just completed our "What would you do with a KX2?" joint contest with
> K6UDA. Here are the winning videos that won a KX2. Pretty cool!
> See:
>
I've a story to add to the list. My wife, KI6SLX was lucky
enough to win a KX2 at the Foothill Amateur Radio Society's
winter banquet. She was very pleased. Her radio experience is
all on VHF/UHF FM, so after digging in the manual for a while,
she asked me, "Do you know how to set it up for
Hi Bob:
Download the kx3 Utility program from the Elecraft web site and check the
firmware version with what you have in the KX3.
http://www.elecraft.com/KX3/KX3_software.htm
The owner's manual has all the information for checking and downloading new
firmware. If you did not get one with our
Hi Bob,
I got KX3 s/n 2000 as a kit. After reviewing the KX3 mod page I have just
ordered the ball bearing optical encoder to replace the supplied magnetic
with sleeve bearing encoder. I also ordered the heavier duty heat sink.
Both are standard on current KX3s.
Enjoy your KX3, it is now my top
Man, I really want to exercise the KAT500/KPA500 $100 off plus Free
Shipping deal...
Don't think I can scrape that much cash together before 28 Feb, though
Heck of a deal!
--
__
Clay Autery, KY5G
MONTAC Enterprises
(318) 518-1389
I presume you're talking of the stranded stuff. Some of that is poorly made.
Years ago, I had a number of wire antennas fail because the strands rubbed
each other in the wind, scraping off the thin coating coating, then rusting.
After that, I went with solid or insulated, stranded copperweld.
Hi Dale,
Sounds like RF is getting in somewhere, somehow! Have you noticed if it's band
specific? Frequency specific?
This happens to me once in a while, and then mysteriously disappears!
73 de Jim - KE8G
Sent from my iPad
> On Feb 3, 2017, at 9:18 AM, Dale Martin wrote:
>
>
Are you by chance running an end fed wire?
73s and thanks,
Dave
NK7Z
http://www.nk7z.net
On 02/03/2017 07:18 AM, Dale Martin wrote:
I've been operating my new K3S for about 2 months now and love it.
Last week, however, something unexpected happened: as soon as I keyed the
paddles or hit f1
Dale,
You have received some good suggestions. I will add look into a common mode
choke on you feed line. You may have one already, if so it may be marginal and
a second one may solve your problems.
Robie - AJ4F
> On Feb 3, 2017, at 09:35, Don Wilhelm wrote:
>
>
Dale,
Try it on a dummy load instead or your antenna.
If the problem is "cured", then look for a problem in your antenna
system - RF is getting back into your shack.
If the problem persists on the dummy load, contact K3support.
73,
Don W3FPR
On 2/3/2017 10:18 AM, Dale Martin wrote:
Last
All:
I picked up an K144XV, a KXV3A and a K3EXREF at a hamfest last weekend from the
estate of an SK.
It was boxed as if to say that the hardware is all I need to implement a GPS
synchronized transverter in a K3 - minus the GPS Rx. I'm not sure that is the
case. (I have a 10 MHz Zyfer GPS
I've been operating my new K3S for about 2 months now and love it.
Last week, however, something unexpected happened: as soon as I keyed the
paddles or hit f1 to key the radio (CW), the radio went keydown. Only by
running the power down below 50-70 watts does it finally key up.
It has
31 matches
Mail list logo