Sorry...used a tablet to reply and forgot about no HTML.
-- Forwarded message --
Hi Royce,
Fast Play (FPLY) is one of the secondary menu functions. Look in the
manual and it will tell you how to disable. It is used to send
pre-programmed CW messages from some of the buttons to
I got the following message on my KX3 yesterday:
Not 0-40C
I was using a 16 hr charge. At some point during the day, I turned it
on, tuned it to 30 m and was just listening. Later on, I turned the
radio off. That is when I got the message.
I have not seen this message and don't remember
I'm just guessing but it sounds like a temperature limit.
Mark. AD5SS
On Sep 30, 2013 5:13 AM, Joel Black w4...@charter.net wrote:
I got the following message on my KX3 yesterday:
Not 0-40C
I was using a 16 hr charge. At some point during the day, I turned it on,
tuned it to 30 m and was
Alan,
You do not need any interface. The only thing you need is a soundcard.
The K3 contains isolating transformers on the Line In and Kine Out rear
jacks.
Just connect 2 stereo cables between the soundcard and those jacks. You
can operate with VOX instead of PTT. Set the Data sub-mode to
Hi Joel,
I have seen the message once while I was charging my eneloop batteries using a
16 h charge. I am not completely sure if the KX3 was on, but I think so. As far
as I know, the message occurs when the batteries are getting too warm while
charging, don't know if this is said in the KX3
Hi
I tried everything suggested and there is no difference, I guess a call to
support is needed.
Thanks for all the suggestions
Tom
Envoyé depuis le Samsung GALAXY S4 via le réseau SFR
Original message
From: Dick Dievendorff d...@elecraft.com
Date: 30/09/2013 07:40
Mike,
It is highly unusual to have a transmit problem on 20 and still have
transmit on 30 meters - those two bands share both the bandpass filter
and the low pass filter.
The fact that you have HiCur messages should point the finger at the Low
Pass Filter.
Are you certain it is receiving
The KXBC3 is simply shutting off the charge current until the cell temperatures
drop back to the 0 to 40 deg. C charging temperature range. Charging will
continue once that happens. (Reference: Elecraft KXBC3 Installation and
Operation Rev A2, page 4). Just another example of the
I'm happy to report that my SB200 is now online between the K3 and KAT 500.
Used it this weekend at the Texas QSO Party. Driving the amp with about 35
watts from the K3 gets about 500 watts out, key down.
Worked without problems. Thanks for all the comments to my earlier
question.
73,
Ron,
I will be at the scene of the suspect power supply the end of next week and
will clean the cable and fuse as suggested. QTH is on the Long Beach WA
peninsula 300m from the beach so connections certainly could use attention.
Maybe it is that simple. I will take my working PS and cable to try
FYi, there is a longer thread on this topic here:
Strange charging issue
http://groups.yahoo.com/neo/groups/KX3/conversations/topics/35321
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I am looking to trade my Drake TR-4 and Power Supply, and Speaker unit with a
microphone for a KX3.
The Drake station is in beautiful condition and works great. Pictures are
available if interested.
This rig sounds and works great, but am needing something smaller to install
in a vehicle.
Please
Price reduced!
For sale to fund purchase of KX3:
KDSP2 module for K2.
I am asking $150 shipped within CONUS.
No, I am not parting out my K2--I've just found I prefer the audio provided
by the KAF2 over that provided by the KDSP2.
My email address can be found on my website:
Hi Shel
Really nice product there!
Can't wait to get one.
Thanks
Gerald - KC6CNN
-
KC6CNN - Gerald
K2 # 5486
K3 # 6254
KX3 # 757
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Ham-Central-Terminal-order-page-is-up-tp7576843p7579411.html
Sent from the Elecraft mailing
Hi all:
I have my remote gear all working extremely well. I can set up the control
end as close as the same LAN as the radio end, or as far as 110 miles away,
and the results are excellent. I have a nagging bug, however.
Quite frequently, but not always, after I have shut down the K3/0 (which
Don,
Thanks for the quick reply and troubleshooting suggestions! I do have the
KPA100 and KAT100 installed so here's what I did:
1. Rechecked 17, 20 and 30M and only 20 was still dead on transmit.
2. Opened the K2 up, checked VFO freq and it was OK (4915). Receive also
OK on 20.
3. Removed
On 9/29/2013 8:52 PM, Jim N7US wrote:
Ron,
I think you're referring to the KPA500, not the KAT500. I'm sorry to have
confused you.
The KAT500 has only one on the parts list.
I've had a couple of extras in nearly all the Elecraft kits I've
built, I think they do it on purpose with the very
Mike,
Glad to hear that it is now working - but I don't like things that just
go away
That sounds like something got temporarily stuck - which usually turns
out to be an unsoldered connection.
I might also suspect a relay contact somewhere.
The relays have wiping contacts, so a few
For General Information -
I ran the KPA500 in the CQWW RTTY contest this weekend. With a drive power
of 15 to 20W from the K3, I kept the KPA500 output between 350 and 400W
output. Even during runs (calling CQ), the temperature never went above 65
degrees on the KAT500 meter. The cooling
Looking over the KXPA100 order information, I wonder, what is controlled
via the RS232 jack (with the KXUSB cable), and what is controlled via the
Ethernet jack/cable?
Are the two jacks on the mid-cord box in the KXPACBL essential to operation
of the KXPA100 with a KX3? Or are they for use
Irwin, I ran mine at 500W for 20 hrs. 1268 QSO fan speed fixe at 4
and no problem. 60% of the time in RUN/CQ mode.
73, Claude VE2FK
From: KD3TB
Sent: Monday, September 30, 2013 11:35 AM
To: 'Elecraft Reflector'
Subject: [Elecraft] KPA500 in the RTTY Contest
For General Information -
I ran
FWIW: I run my KPA500 at 500W in any mode [well ... not PSK31 :-)] and
it handles it just fine. I seem to remember, during the KPA500 field
testing, that Jim, K9YC, was told to run his at 700W in a RTTY contest
and it did it just fine there too. Difference between 400 and 500 is
less than
Will the KPA500 work on HF freqs outside the ham bands ie., MARS freqs?
Thanks,
Jack
W4GRJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I run mine on 6 meter meteor scatter at full power all the time. Sometimes for
up to an hour continuous (30 seconds on, 30 seconds off). I have mentioned
this to Elecraft and they didn't have any concerns about it.
73 de Sebastian, W4AS
On Sep 30, 2013, at 3:36 PM, Fred Jensen
On Mon, 30 Sep 2013 15:27:13 -0400, Claude Du Berger wrote:
Irwin, I ran mine at 500W for 20 hrs. 1268 QSO fan speed fixe at 4
and no problem. 60% of the time in RUN/CQ mode.
FYI, that is NOT a fixed speed. It is just the minimum speed that it
will run instead of ramping down to the lowest or
On Mon, Sep 30, 2013 at 12:00 PM, Fred Jensen k6...@foothill.net wrote:
On 9/29/2013 8:52 PM, Jim N7US wrote:
Ron,
I think you're referring to the KPA500, not the KAT500. I'm sorry to have
confused you.
The KAT500 has only one on the parts list.
I've had a couple of extras in nearly
Your NiMH cells are at or almost fully charged. Near the end of the charge
cycle, the NiMH cells convert more and more of the charge current to heat, and
less to chemical conversion (charging). When the cells reach 40deg. C, the
KXBC3 suspends charging until the cell temperatures drop below
Yes, I've found that simply restarting the control RRC seems to work for
me.. It's an annoying work-around but less odious than the things you've
been doing. Of course, your failure mode may be different, but the
description sounds the same.
73,
/Rick
On Mon, Sep 30, 2013 at 11:16 AM, Brian F.
Restarting the control RRC rarely solves it for me, unfortunately. Thanks.
--
70 is the new 40.
Brian F. Wruble, C.F.A.
1107 Key Plaza, PMB 447 Key West, FL 33040
Summers: P.O.Box 57, 7400 Augustine Herman Highway, Georgetown, MD 21930
eFax 305.768.0278 Skype bwruble
On Sep
I replied to Jim off line. That washer is not used. I prepared an errata
today removing it.
The parts lists are created fairly early in the development phase of a
project. I write the kit assembly instructions much later. Usually both the
factory and I audit the parts list to ensure it matches
Will the KPA500 work on all freqs outside the HF Ham bands.
I want to make sure it will function on MARS freqs.
Jack
W4GRJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I have a friend who uses a K3/0 and remotes to my K3/100 and we haven't had any
connection issues yet. He lives 100 miles from me. Our ISP's are Comcast.
73, Steve K6SAB
On Sep 30, 2013, at 5:10 PM, bwru...@gmail.com wrote:
Restarting the control RRC rarely solves it for me, unfortunately.
I believe that the author of this software has closed his website and is no
longer offering this software.
Does anyone have the installation file that they could send me direct? I
have a new netbook and can't find my original installation file.
I really miss the SWR scanning aspect of this
I recently attempted to down load the latest firmware for my P3, and now
have a problem, the P3 says Boot loader checksum failure, ready to
download. However the computer cannot find the P3. So now I do not have,
what I come to rely upon my ability to see what is going on around the
frequency I am
I tried but your email addy bounces
Rick wa6nhc
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of bill.va...@gmail.com
Sent: Monday, September 30, 2013 6:41 PM
To: elecraft list
Subject: [Elecraft] K3 EZ
I believe that the
http://www.na6m.com/EZ-K3/K3_EZ_V2005.zip
[http://www.na6m.com/EZ-K3/K3_EZ_V2005.zip]
http://www.na6m.com/EZ-K3/K3_EZ2007.zip
[http://www.na6m.com/EZ-K3/K3_EZ2007.zip]
http://www.na6m.com/EZ-K3/K3_EZ_V2008.zip
[http://www.na6m.com/EZ-K3/K3_EZ_V2008.zip]
-Original Message-
From: Rick
36 matches
Mail list logo
