For a K3 used during Field Day, the power, compression, and mic gain can
be locked by pressing 1 from the PWR SET menu. I was wondering if there
is a way to lock the antenna selection on radios which have the KAT2
installed? If not maybe this could be added to a future firmware update
by
Very interesting, Ed, and your web page is too.
I see that the KX3-2M is in a screened box positioned immediately on top
of the ATU. Does the position of it have any detrimental affect on the
operation of the ATU on the normal KX3 bands (1.8 to 50MHz)? I do not
see any mention of this in the
Hi Darren,
I have a later KX3, number 5111, with similar options to you, built in ASTU
and KX3 hardware, but I don't have the battery charger or additional
heatsink options.
I built mine from the kit. It was very straight forward but I did buy an
anti-static mat first.
BTW - I made a
Very sorry, there's a typo in my message.
The 1st screen shot (timed at 11:22) is with the KX3 off and the one at
11:23 is KX3 on. Sorry for the confusion.
Dave (G0DJA)
- Original Message -
To: elecraft@mailman.qth.net
Sent: Friday, June 27, 2014 10:39 AM
Subject: Re: [Elecraft]
N1MM is probably the MOST popular contest logger. There are 4,580 current
members on the list below and you'll probably get answers there faster than
here.
https://groups.yahoo.com/neo/groups/N1MMLogger/info
73, Bill W4ZV
--
View this message in context:
Mike,
I always put a dummy load on the unused antenna connector for that very
reason. Adds a margin of safety for FD and demo events.
73,
Don W3FPR
On 6/28/2014 2:47 AM, Michael Eberle wrote:
For a K3 used during Field Day, the power, compression, and mic gain
can be locked by pressing 1
Many thanks, Ed, it is thankful to know that the operation of the ATU is
unaffected.
73 de David G4DMP
In a recent message, Edward R Cole kl...@acsalaska.net writes
I should have taken a photo before installing the shield. No it has no
effect on the ATU if you follow instructions on routing the
Hi Dave,
I've have just repeated my measurements of the 7.080Mhz sprog on 398.4MHz and
posted some screen-shots on my blog. See here:
http://www.g0hww.net/2014/06/kx3-uhf-emissions.html
Cheers, 73
Darren, G0HWW
On 28/06/14 10:30, Dave wrote:
Hi Darren,
I have a later KX3, number 5111,
Hi Darren, and everyone else following this...
I've found it! Very low level, but by zeroing in on 385 to 386MHz I found a
small signal that moves when I tune across 7MHz...
At 7.000MHz there's a signal at 385.027MHz (-78dBm) which moves up in
frequency, staying at about the same signal
For a long time I have been using HRD to allow rig control of my K3 -
using the mouse and computer for control of various features/controls
and the VFO. Then I discovered the Pigknob - http://pignology.net/pigknob/
The Pigknob allows me to control 8 programmable features and the VFO (at
two
A couple of things I've wondered about:
1) Can you load firmware while the device is connected?
2) Are there any issues if a P3 is daisy-chained?
I looked at the Pigknob user manual and the answers weren't obvious.
On 6/28/14 6:50 AM, Bill W2BLC wrote:
For a long time I have been using HRD to
Thanks for following up on this Dave, it is really appreciated. At least I know
that it's not just my KX3 now.
Cheers,
Darren, G0HWW
On 28/06/14 14:10, Dave wrote:
Hi Darren, and everyone else following this...
I've found it! Very low level, but by zeroing in on 385 to 386MHz I found a
On 6/28/2014 8:27 AM, Vic, K2VCO wrote:
A couple of things I've wondered about:
1) Can you load firmware while the device is connected?
Yes ... to the PK [macros] and K3/P3 [firmware et al]. It comes with a
little circuit card, mine just hangs behind the P3 in the not-wireless
region of my
Test only
'IN GOD WE TRUST'
KØAZ Mike Sanders EM37cd SouthWest
Missouri
www.k0az.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Hello, I would like to know how accurate is the display of PS value. I
suspect it always shows lower value by about 0.2 to 0.3 V. For instance,
when I use Li-Po accupack 3S1P 3300 mAh that normally gives 35C, i.e. some
100 A (therefore I think it has no problem with internal resistance at low
Yes, the KX3 has a diode to protect against reverse polarity. That has a
voltage drop of about 0.3V.
wunder
K6WRU
On Jun 28, 2014, at 10:50 AM, ok4rm radio.miskov...@gmail.com wrote:
Hello, I would like to know how accurate is the display of PS value. I
suspect it always shows lower value by
Folks,
Can a single Elecraft FM filter support AM and FM transmit and receive for
occasional use with a K3?
Thanks,
Bob W1XT
Sun City West, AZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Yes - effective with MCU 4.57 for AM transmit
MCU 4.57 / DSP 2.79, 10-24-2012
* AM TRANSMIT CAN USE THE FM FILTER: The wide (FM) crystal filter can
now be assigned to AM transmit as well as FM. This can potentially
free up a crystal filter slot for customers who were using the 6-kHz
filter
There is an issue with the P3 involving the programming of the Pigknob.
However, it is very simple to correct - simply turn the P3 off when you
are programming the Pigknob. I have no long winded scientific
explanation for it, hence cannot provide to the bandwidth of the topic.
I have been
A hugely useful feature!
To make perfect (e.g. for SOTA use) would it be possible to interpret empty
message memories as non FAST-PLAY?
This would allow to use e.g. BAND+/- for quick band changes and FREQ ENT for
1-touch message play/repeat without toggling back and forth FAST-PLAY mode.
73,
The new K3 Utility (and P3 Utility) is giving me an error every time I try
to download the new FW : InternetFindNextFile completed with error 0x006
: the handle is invalid.
What do I need to do ? Need this urgently.
73, Jamie
WB4YDL
Try using Internet Explorer to access the FTP site and copy the files to
your computer's file system.
See K3 Utility Help, Manual File Transfer
The URL for K3 firmware is ftp://ftp.elecraft.com/K3/firmware
The URL for P3 firmware is ftp://ftp.elecraft.com/P3/firmware
The K3 and P3 Utility use
22 matches
Mail list logo
