[Elecraft] K3 For Sale

In making my plans for a K3s upgrade, I have decided to sell my K3. I am going to remove all of my optional filters and only include the 2.8, 8 pole SSB. Currently running the latest firmware. K3 100 S/N 504 with all updates except for the enhanced Lf bandwidth DSP ATU KXV3 KBF3 This has been a

[Elecraft] filter shift

Hi Al, tnx for the answer (the only one, hi). The phenomenon is still here, so I'll be waiting what will be in the future, or maybe somebody from Elecraft will have the solution... Best regards OM7VV Peter __ Elecraft mailing list Home:

Re: [Elecraft] K3S Proper Grounding

Good information David. I also Have a 80m OCF http://www.slickpic.com/users/GeneGabry/albums/N9TFHamStationPhotos/?wallpap er #8644290 and choosing the correct balun and RF choke is paramount. I went with

Re: [Elecraft] KX3 RX optimization

I find the audio FX delay feature really makes a huge difference in my headset. I'm not sure how/why but I hear and copy better with it turned on. I currently run the delay at 5. Jer -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On

[Elecraft] KX3 RX optimization

Most of you have probably already discovered this, but the following points I have found for CW operation (some of it applies to all modes) may be of help for new owners of a KX3: 1. The default 30dB of preamp gain isn't always a good choice. If I notice that the noise level (without signals)

Re: [Elecraft] K3S Proper Grounding

Part of my confusion is based on this being a commercial solution that didn't have a problem until recently. One thing I've thought of is that my TV configuration may have changed with the addition of a Chromecast..etc.. so I'll be doing a clean setup troubleshooting here soon (remove everything

[Elecraft] Re KAT500 Fault

Dave, I recently purchased my KAT 500 and if I remember correctly the manual says it will fault for over 1K power. If you have 1500 w that is the cause. 73 Mike KF6KXG __ Elecraft mailing list Home:

[Elecraft] VFO B is tracking VFO A

A related question: What is difference between VFO IND  and VFO LNK ?  I ask because I recently installed the 2nd  receiver and had set VFO IND to Yes. I then noticed that when trying to use the SCAN feature that when I press M>V, only VFO A was being populated with the stored memory not VFO B.

Re: [Elecraft] VFO B is tracking VFO A

paul ecker wrote: > A related question: What is difference between VFO IND and VFO LNK ? VFO IND = NO (default) keeps VFO A and B on the same band at all times. VFO IND = YES allows VFO B to be on a different band. This is most useful with the sub receiver. VFO LNK just

Re: [Elecraft] K3S Proper Grounding

On Thu,10/1/2015 8:11 AM, ae...@carolinaheli.com wrote:: Part of my confusion is based on this being a commercial solution that didn't have a problem until recently. Buying "a commercial solution" seems to mean that you're assuming that whoever is selling a product really understands how

Re: [Elecraft] VFO B is tracking VFO A

On Oct 1, 2015, at 9:18 AM, paul ecker wrote: > Wayne - Tnx for explanation. Further question. > VFO IND = YES allows VFO B to be on a different band. This is most useful > with the sub receiver. > > So if I have VFO IND set to YES, does this preclude using the SCAN

Re: [Elecraft] KS3 Proper Grounding

It shouldn't be "if", it should be "when." On Oct 1, 2015, at 8:58 AM, James Wilson wrote: > Jer, > > If you run the connecting ground around the house on the outside, you may > consider adding several ground rods to that connecting run just to break up > possible loops. >

[Elecraft] KS3 Proper Grounding

Jer, If you run the connecting ground around the house on the outside, you may consider adding several ground rods to that connecting run just to break up possible loops. > ... the main ground on the other side of the house. >I'm not sure how I'll NOT end up with a ground loop >in this

Re: [Elecraft] VFO B is tracking VFO A

Wayne - Tnx for explanation. Further question. VFO IND = YES allows VFO B to be on a different band. This is most useful with the sub receiver. So if I have VFO IND set to YES, does this preclude using the SCAN feature? 73 Paul From: Wayne Burdick To: paul ecker

Re: [Elecraft] ACC2

I need to clarify some of my misconceptions about ACC2 and offer some unfortunate experience with the special cable package offered with the KXPA100 when integrating to the KX3. First off the GPIO function has nothing to do with interface to the amp. Perhaps that is why there is no reference

Re: [Elecraft] KAT500 Fault

dave_w0ru wrote > With the * > KAT500 * > in Standby, I can tune with the KAT500 just fine. That should read: With the *KPA500* in Standby, Dave w0ru -- View this message in context: http://elecraft.365791.n2.nabble.com/KAT500-Fault-tp7608563p7608580.html Sent from the Elecraft mailing

[Elecraft] Update: K3 Issues Since Synthesizer Upgrade

Several days ago I posted the below to the Reflector. After a couple of days of reproducing the below errors, I can safely say that NONE of them are connected to the Synthesizer Upgrade. Since they all happened since the upgrade I made the incorrect assumption that that had something to do

[Elecraft] The KSYN3A synth will always be available as a K3 upgrade

Hi all, Just to put an end to any unfounded rumors: The KSYN3A will always be available for K3 upgrades. We use the same synth module in the K3S, and there is no end date. 73, Wayne N6KR __ Elecraft mailing list Home:

Re: [Elecraft] K3S Proper Grounding

On Thu, Oct 1, 2015 at 12:58 PM, Jim Brown wrote: > What these two measures can do for you is CONTROL where common mode > current flows -- it will flow on that new ground wire and that new > dedicated power line -- but that RF current will still RADIATE, and can be >

Re: [Elecraft] ACC2

Frank, I'm sorry to hear that the cables had to be replaced. This is very unusual. We have them custom made and they're supposed to be 100% tested. I'll get this feedback to our manufacturing supervisor. 73, Wayne N6KR On Oct 1, 2015, at 10:10 AM, bsusb wrote: > > I need

Re: [Elecraft] Update: K3 Issues Since Synthesizer Upgrade

OK, Dennis, I'll try to reproduce this. Wayne N6KR On Oct 1, 2015, at 11:14 AM, Dennis wrote: > Wayne > > I've tried to reproduce #2 with no luck. It happened several times during > the contest, but I couldn't draw > any conclusions with what I was doing and the

Re: [Elecraft] K3S Proper Grounding

We're had a lot of posts on this topic. Ltt's let it rest for now in the interest of relieving list email overload for others. thread closed. 73, Eric /Moderator etc. elecraft.com/ On 10/1/2015 9:58 AM, Jim Brown wrote: On Thu,10/1/2015 8:11 AM, ae...@carolinaheli.com wrote:: Part of

Re: [Elecraft] Update: K3 Issues Since Synthesizer Upgrade

Wayne I've tried to reproduce #2 with no luck. It happened several times during the contest, but I couldn't draw any conclusions with what I was doing and the pops. I've played with the K3 for several hours after the contest but have not had the pops reoccur. #4 is easily reproduced. In

Re: [Elecraft] K3S Proper Grounding

This whole thread is quite amusing, no matter how much explanation takes place, people still believe a ground rod is RF ground . Then the poor guy with the problem who states "nothing has changed" admits he has not grounded the station gear yet. but it was before. Talk about a lot of posting

Re: [Elecraft] Update: K3 Issues Since Synthesizer Upgrade

Hi Dennis, > #2- I have heard a number of loud audio "pops" since the above changes. Please email me directly with a description of how these pops can be produced, i.e. what controls you're using at the time. > #4- During CQWW RTTY, if I was transmitting and pushed a key- say A/B, or > Rev-

Re: [Elecraft] Update: K3 Issues Since Synthesizer Upgrade

About #2, make sure you did not accidentally have the AGC off. If you like to operate without AGC, you can set the AGC to not cut in until a signal is quite loud, and then holds anything higher to the same level. It's kind of like AGC OFF with a safety valve. 73, Guy K2AV On Thu, Oct 1, 2015 at

Re: [Elecraft] Update: K3 Issues Since Synthesizer Upgrade

I got a few of the ERR KEY messages as well, I am unable to reproduce them as well... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see:

Re: [Elecraft] K3S Proper Grounding

Ouch Please discontinue this thread. I'll keep the rest of what I want to say to myself. -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Merv Schweigert Sent: Thursday, October 01, 2015 1:30 PM To: elecraft@mailman.qth.net

Re: [Elecraft] The KSYN3A synth will always be available as a K3 upgrade

Wayne, THANK YOU! That mindset youhave is why I bought Elecraft! -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see:

[Elecraft] K3/P3 issue

Perhaps I missed the answer to this... My SVGA external monitor shows signals about 1/2 to one S unit lower than my P3 does on the native screen... What am I missing? If I use Peak Hold, there is a clear 1/2 to one S-Unit difference in teh display height... -- Thanks and 73's, For equipment,

[Elecraft] P3 Problem

My P3 can't seem to remember its firmware. When I turn it on, it looks right, but as soon as I press Ref Level, it goes into the P3 Boot Loader screen. I've reloaded the firmware (latest) 3 times and the same thing keeps happening. I have disconnected and reconnected the power cable to no avail.

Re: [Elecraft] K3S Proper Grounding

This thread was closed over 2 hours ago. 73, Eric /elecraft.com/ On 10/1/2015 12:18 PM, ae...@carolinaheli.com wrote: Ouch Please discontinue this thread. I'll keep the rest of what I want to say to myself. __ Elecraft mailing list

Re: [Elecraft] P3 Problem

Hi Ken, A 'parameter reset' should solve the problem. Hold down the MENU button while pressing the POWER button. This will reinitialize all the parameters to their default values. 73, Paul -- View this message in context:

[Elecraft] Fwd: P3 Problem

Sent from Jerry's iPhone Begin forwarded message: > From: Paul Saffren N6HZ > Date: October 1, 2015 at 1:41:23 PM PDT > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] P3 Problem > > Hi Ken, > > A 'parameter reset' should solve the problem. Hold down the MENU

Re: [Elecraft] ACC2

Wow I am thoroughly amazed at the fact that any reseller is listening to their customer base. I feel fortunate and proud to own your products. N5NIS Sent from my iPhone > On Oct 1, 2015, at 2:04 PM, Wayne Burdick wrote: > > Frank, > > I'm sorry to hear that the cables

Re: [Elecraft] K3/P3 issue

Hi David, Check your inbox/spam folder, I emailed you directly on this. -Paul -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-P3-issue-tp7608605p7608606.html Sent from the Elecraft mailing list archive at Nabble.com.

Re: [Elecraft] ACC2

Wayne, Thanks. Your radio products are too good in quality and performance to get undeserved black eyes from faulty cable sets. Could very well have been a one-off. On Thu, 1 Oct 2015 12:04:01 -0700 Wayne Burdick wrote: > Frank, > > I'm sorry to hear that the cables had

Re: [Elecraft] K3/P3 issue

Nothing, but THANK YOU... Can you remail me please... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For

Re: [Elecraft] KAT500 Fault

Hi Dave, I don't have the full context of your note but here is some information that may help: 3.9.5 Tuner Fault Conditions The FAULT LED being lit does not mean there is an equipment failure to cause you concern. Rather, it indicates a condition that you should correct. A fault will

[Elecraft] Strange K3 microphone /PTT fault

Greetings folks, I'm puzzled. my 7 year old K3 did two strange things this evening. During a CW QSO on 21MHz, it appeared not to go back into receive and required power off and on to operate. The QSO finished. Then, in the middle of a USB QSO on 5MHz - mid transmission, it went back to receive

Re: [Elecraft] K3/P3 issue

For a continuous CW tone, the level should be the same on the P3 and the external monitor. For SSB, the SVGA display should read 1/2 S-unit lower. The reason is that, unlike CW, an SSB signal is spread out in frequency. Since the SVGA monitor has twice the frequency resolution than the P3

Re: [Elecraft] Strange K3 microphone /PTT fault

Hi John, If it were me, I'd reseat the front panel assembly to the RF board. I had to do this many moons ago (like 8 years...) one time and it fixed the problem. The only guess I have for what's wrong is some minor corrosion on on some of the front panel pins. John, I hope this does it for

Re: [Elecraft] Strange K3 microphone /PTT fault

If Pins 7 and 8 are connected together (verify with ohm meter) but not connected to the mic jack shell, you may wish to remove the front panel assembly and look just above the Mic Jack at a component labeled "L4". It should be a short. If it is broken, or other than a short, replace it with

Re: [Elecraft] KAT500 Fault

Fred, I am now trying the KAT500 output going to a dummy load. When the K3 is set at about 22 watts out, the KPA500 shows 440 Watts out. When I use the Tune feature on the K3 with Manual Tune feature on the KAT500, there is no fault. However, when I send with the K3 keyer and with Manual Tune on

Re: [Elecraft] K3S Proper Grounding

I think we are drifting off topic, my apologies, but if you are considering an ocf dipole you can only prevent common mode currents by use of a double wound balun, ie 2 separately made chokes connected together as a 4:1. A single core version does not properly cancel the common mode current that

Re: [Elecraft] Update: K3 Issues Since Synthesizer Upgrade

> #4 is easily reproduced. In SSB mode, activate the PTT. Push the REV key, > and one of two things happens: > if you keep the radio keyed, ERR PTT shows on VFO B until you unkey it, then > its followed by ERR KEY. > Happens with any key that doesn't function when you're transmitting. When it

[Elecraft] KXBC3 Clock accuracy

Hi to all The accuracy of the KXBC3 clock is at best marginal ... But ... Looking at the schematic of the KXBC3, the real time clock seems to be a part of chip PIC24F16KA10. And a reference to that chip says this: 29.3.9 Calibration The real-time crystal input can be calibrated using