Yes
With mic sel displayed tap 1 to toggle between hi and low.
Enjoying breakfast on the way to seapac. :)
73
Greg
Sent from my iPhone
On Jun 4, 2010, at 9:47 AM, Tom W8JI w...@w8ji.com wrote:
Isn't there a high and low gain setting, besides just the
numerical gain??
:-)
- Original
Or u can use an ext keyed on the key in Jack and a paddle on the
paddle input using the int keyer.
Sent from my iPhone
On Jun 4, 2010, at 2:54 PM, PHIL n2...@stny.rr.com wrote:
I may be way off base here but I am curious...Has anyone ever tried
using a y cord to hook two sets of paddles
DXLab's WinWarbler has user programable command lines that can be
executed when changing modes. I use them to set the specific data
mode and also to send the PC command to set the power level I want.
For example when selecting PSK31 it sends the command to the radio to
select data-a
DXLab's WinWarbler has user programable command lines that can be
executed when changing modes. I use them to set the specific data
mode and also to send the PC command to set the power level I want.
For example when selecting PSK31 it sends the command to the radio to
select data-a mode,
I've talked to Lyle about this and he is going to look at it when he
gets back from a trip he is on.
73
Greg
AB7R
On Aug 16, 2009, at 12:22 PM, Dick Roth, KA1OZ wrote:
Tried listening for the Elecraft SSB net at 1800. There was a
heterodyne or other interfering signal on 14.316. I tried
I ALWAYS use the button to test communications before I do anything.
CUL Dick! You going to be up on the island this weekend?
Greg
On Aug 11, 2009, at 7:25 PM, Dick Dievendorff wrote:
I get this all the time when I test the K3 Utility's ability to load
a K3 in
this state.
Be very sure
Looking for some assistance in setting up SDR-IQ. I ran the setup and
connected the IQ and it is receiving sigs from the K3's IF.
The problem is I cannot get it to communicate with the K3 to follow
frequency changes from the radioor when clicking on a signal to
have it change the
] On Behalf Of Gregory Fischer
Sent: Friday, July 31, 2009 6:16 PM
To: Elecraft Reflector
Subject: [Elecraft] SDR-IQ users?
Looking for some assistance in setting up SDR-IQ. I ran the setup and
connected the IQ and it is receiving sigs from the K3's IF.
The problem is I cannot get
The LCD cannot be changed. But if you are not using the VFO B
information you can tap DISP for the alternate display and adjust it
so that it shows the RIT offset all the time.
73
Greg
AB7R
On Jul 26, 2009, at 5:47 AM, Steve Ellington wrote:
I agree. I seldom use vfo B. I don't want my
I used my sig generator and use the k3 auto spot to zero beat. Then
adjusted the offset till the two tones matched (listening to the k3
and power sdr at the same time.
Greg
Sent from my iPhone
On Jul 24, 2009, at 6:25 PM, W2XB haircut...@verizon.net wrote:
Hi Dave,
to get the SDR and
If someone finds themselves in need of some off the wall resistor let
me know...I may have one. I went to a garage sale (more like a block
sale) in Anacortes Saturday morning and found 3 parts cabinets chock
full of resistors. The parts drawers are even labeled. :) There's
gotta be a
Was great meeting everyone at SeaPac this past weekend (My feet still
hurt). :) Thanks for stopping by the Elecraft booth.
73 till next year!
Greg
AB7R
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Don't forget to update ALL the files when going to the new firmware.
That includes the DSP files, FPF file and the DSP data tables.
73
Greg
AB7R
On May 3, 2009, at 10:36 AM, Matt Zilmer wrote:
Hi Gregg,
I've been using 3.11/2.15 for some time and have never observed what
you describe.
Excellent. 73 and enjoy Gregg!
Greg
AB7R
On May 3, 2009, at 10:51 AM, W6IZT wrote:
Reloaded the FW and the problem is resolved. thx
-Original Message-
From: Gregory Fischer [mailto:a...@cablespeed.com]
Sent: Sunday, May 03, 2009 1:45 PM
To: mzil...@verizon.net
Cc: W6IZT
Hi Julian. You should be seeing readings around -30 or better.
Are you using PSK-D with the paddles or a soundcard program with Data-A?
Set your soundcard output level to about 30-40%. Then with the K3 in
Data/Data-A mode start with the line-in gain at 1(MIC gain control
becomes Line-in
Doug.
You have your tones set on the K3 Pitch to something different than
your digital mode software is set to. If you set them to the same
(usually 2125 with 170Hz shift) you will be all set.
73
Greg
AB7R
On Apr 30, 2009, at 11:19 AM, Doug Freeman wrote:
I am trying to determine if I am
Jim,
If you have the power set above 13W it will say HP. Exit the menu and
change the Power setting to below 13W and it will say LP.
73
Greg
AB7R
On Apr 30, 2009, at 6:00 PM, W3CP wrote:
The K3 went to LP yesterday without me knowing it. I was surprised
that no
one on the QCWA CW net
If you are running PSK31 from a computer digital mode program you must
use Data-A. PSK-D is ONLY for use with either paddle input or ascii
input over the serial port using a terminal program or the K3Utility
program.
73
Greg
AB7R
On Apr 28, 2009, at 3:23 PM, Phil LaMarche wrote:
Using
HOLD the CMP/PWR knob to activate the MON level and adjust as desired.
73
Greg
AB7R
On Apr 18, 2009, at 1:47 PM, Jeff wrote:
A little off topic but the same programs. I'm also using DM-780 and
all
seems to be fine.
I'm just wondering, on transmit I hear the output in my speaker
The setup I use with an array solutions six pack remote switch is to
have ANT1 and ANT2 both going to the six pack. This way I can mix and
match any of my available antennas to optimize diversity receive.
73
Greg
AB7R
On Apr 7, 2009, at 3:44 PM, jeff kb2m wrote:
I spent the morning
Arie,
Are you changing bands from the K3 band up/dn button or are you using
some software program to select the bands?
73
Greg
AB7R
On Apr 3, 2009, at 10:39 PM, Arie Kleingeld PA3A wrote:
Loaded FW 3.06 yesterday. All OK except
This morning I cycled through the bands and found 6 meters
@mailman.qth.net'
Cc: 'Gregory Fischer'; 'augie.han...@comcast.net';
'evernhamm...@verizon.net'
Subject: RE: The rules show a Send To field without a name and
address
(was [Elecraft] EQP 2009 results for KB0YH)
Importance: High
Today at Sun Mar 15 17:00:27 EDT 2009 Gus Hansen (KB0YH) wrote
This is more than likely due to dirty signals on the TX end. I was
using a QS1R connected to the K3 IF and measured the width of some of
the strong signals. Some were as wide as 2.6 kHz Not very good
for a CW signal. In this case there is just not much you can do.
73
Greg
AB7R
On
Im in the middle of the RTTY RU and running great. Regarding the IMD
in PSK I got the following results as noted below
Begin forwarded message:
From: Gregory Fischer a...@cablespeed.com
Date: January 2, 2009 9:16:33 PM PST
To: Wayne Burdick n...@elecraft.com, Lyle Johnson k
That will work too. but if you already have something in the Key In
jack it makes it bothersome. Its easier to put the K3 into FSK-D.
Then the footswitch will do exactly what you want.
Greg
AB7R
On Dec 31, 2008, at 8:55 AM, Bob Tellefsen wrote:
In CW mode plug the FS into the KEY jack.
customer
problems. I knew about HRD but never used it.
Thanks again ... another feather in the cap for the Elecraft crew !!
This might be of interest to others ... wonder if it should be
posted on the Reflector ?
Joe, W5ASP
--- On Mon, 12/29/08, Gregory Fischer a...@cablespeed.com wrote:
From
You should be able to change it from bothI just tried it and it
worked fine from both BSEt and using the RX ANt button.
Merry Christmas!
Greg
AB7R
On Dec 25, 2008, at 6:24 AM, K2MK wrote:
Hi Frank:
I think I have your answer. Try this.
Turn the SUB on
Don't press BSET
Hold RX ANT
You
I hear a click when KRX3 in CONFIG is set to either ATU or BNC.
BTW, you do not need to use BSET and then ANT to change between Main
and AUX for the sub receiver. You can do it with a HOLD of the RX ANT
button too.
73 and Merry Christmas
Greg
AB7R
On Dec 24, 2008, at 2:53 PM, Frank R.
With DataA you need to adjust the LineIn gain so that you have 4 bars
of ALC action.
73
Greg
On Dec 14, 2008, at 6:06 PM, Bob Cunnings wrote:
Have you tried adjusting TXG VCE? With latest firmware, a setting of
-2dB puts my PSK31 power right where it belongs for a given requested
power out.
Wayne is working on this bug and it should be fixed in the next release.
Thanks!
73
Greg
Begin forwarded message:
From: Gregory Fischer a...@cablespeed.com
Date: December 14, 2008 8:22:06 PM PST
To: Dick Housden, W0NTA w0...@arrl.net
Subject: Re: [Elecraft] Strange problem when switching
30 matches
Mail list logo
