Testicle? Testicle?
Greetings and Salutations.
FWIW, my 81 VW dasher diesel hydro-locked one day when I had taken my kids
back to their mother. Went out to go back home, engine would not turn. Took
out a glow plug and cleared the cylinder and drove slowly home. New Head
gasket and klatta klatta klatta.
TTFN
Deneal.
I suggest that you READ what was written. Viscounts corroded, mostly in the
belly area, and it was not checked, found or fixed until there were a
number of failures. The Hawaiian airliner that lost its' roof was a
victim of corrosion and poor maintenance.
To re-state:- Comet Two's
Hi,All.
This is an OT request for info about Stereo speaker repairs. I have an
old, circa 1980, pair of made in Poland stereo speakers that need
repair/replacement of the foam plastic suspension stuff around the
speaker cone. The speaker cone itself is in as new condition, the foam has
Rich, Jin, John.
Thanks for the info. Time to Gargle? Snapple? Oh! Ggle!
TTFN
Fred Moir
Lynn MA
Where it is always Friday!
Hi, All.
I've had 2 81 VW's, Rabbit and Dasher wagon, The only fuel related problem
that I had with either of them was that the hose from the tank to the fuel
line, in the rear of the car , was braided hose and when checked
(finally!) was found to be wet. (sound familiar?). Replacing the hose
To exorcise a Pastafarian you'll need Marly's Ghost!
Fred Moir
Lynn MA
Hi, all.
To replace an old connecting rod with a new updated rod may be possible if
you can remove the old rod and have the new rod matched to the old. If not
the extra mass of the new and stronger, i.e. heavier, rod will throw things
off. Consider, the few grams of extra mass will be
USVI
At 08:41 AM 12/7/2005, you wrote:
OK. Here is my trivia question:
Where in the United States do folks drive on the left? (Unless it has
changed in the last 20 years).
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Rich Thomas
Sent: Tuesday,
Hi, All.
I have an '85 190E now reduced to a parts vehicle. (rust and second dead
trans.) 170K good engine, new chain and gear etc. properly looked after the
engines will do much more. My $.02
Fred Moir
Lynn MA
Three of them thar compession ighnition thingys.
Echo?
Okay you jokers.
I've been unable to send to the list, rx okay. Returned mail is marked as
no such address. My ISP is not the greatest at informing people when
they add features and they said that there was nothing wrong at their
end. So how am I suddenly able to send to the list? Funny
LT.
I have been (PAST tense, and so am I)
Fred Moir
Lynn MA
At 05:11 PM 12/29/2005, you wrote:
But you ARE posting to the list. You just did.
On 12/29/05, frederick w moir [EMAIL PROTECTED] wrote:
Okay you jokers.
I've been unable to send to the list, rx okay. Returned mail is marked
Hi, Barry.
I used to have a computer repair company, and the things that I would try
would be:-
1. Remove all cards and drive cables but the video card and try it again.
2. Try another power supply, test again.
3. Buy another MB.
Rotsa Ruck!
Fred Moir
Lynn MA
Curt.
How about Shaft? Driveshaft plus the guy in the movie? Maybe how you
feel! Sorry couldn't resist.
Fred Moir
Holy cripes! I think I just got the name for the 190D. I was thinking
about how long its taking to get it driveable (still waiting on that
driveshaft, hopefully Friday) and I
Hi, All.
There is a piano mover around the Boston area you might like, they have a
shiny black cube van and the name of the company is Death Wish Piano Movers.
LOL
Fred Moir
Slumbering Diesels
Hi, All.
Peugeot Moovie, Interesting concept. If it came over here it would look
like an Hummer after Federal improvements!!
Very happy to be in a SAFE Benz, diesel, of course!
TTFN
Fred Moir
Hi, All.
If the Benz list were for one dimensional people, I'd have to go
elsewhere! You even put up with me!! (mostly).
Whoever needed a blower motor for a 190/300 car, my local JY wants $30 and
take it out yourself. I could do this, if you would pay shipping.
Sorry to be so
Hi, All.
If I were to get a gun rack for my 190DT would it be best to get an M1 to
put in it? Or should I get a firearm because winter is coming and soon it
will be Colt?
TTFN
Fred Moir
The old diesel infested guy with the lousy jokes.
Hi, All.
LT Don, so if It's not to be diesel would AvCat or AvTag be OK?
I could use what another member of the (60's) R.A.F. used, 70% AvCat, 20%
turbine oil and 10% Red Hydraulic Fluid. Ran OK in a Perkins and was free,
(sort of).
TTFN
Fred Moir
Diesel in my veins (and you can see
Anybody there?
Fred Moir
Lynn MA
Hi,All.
Local Want Ad.
85 300TD New starter. alt., calipers,rotors and muffler sys. Gray w/tan
int. 220k miles Many extra parts. $700 Motivated seller.
E mail is better. [EMAIL PROTECTED] (Jefferson MA) 508-829-7358
83 300TD Runs. Gd for parts. Midnight blue w/blue int.
Hi, All.
OT! Not too long ago there was a (mercifully) brief discussion of the
Chevrolet aluminum 4 and the car it ended up in. This week I found a 1970
Car Life magazine with an article about the XP-887 engine , read Vega,
engine, Mopar engines and a proposed mid engine Corvette plus a
/2005, you wrote:
Hello.I would love to have that magazine as I am an AMC nut!!!...I try
to get every article I can to HOPEFULLY decorate the walls of my
garage...Mike
- Original Message -
From: frederick w moir [EMAIL PROTECTED]
To: Mercedes mailing list [EMAIL PROTECTED]
Sent: Wednesday
Hi, All.
Well, today I went to the JY and proceeded to pull an heater fan for my
201. Brain fart city! Took one out of a 300E (can you say 124?). Any one
want a good Fan motor assy. with porcupine for $40?
On another note, this afternoon I briefly saw a BMW Vixen motorhome. Odd
looking
Make room! Make room!
Fred Moir
Lynn MA
If dead cats work, so will dead people! Sort of a variation on Soylent
Green.
Marshall
--
Marshall Booth Ph.D.
Ass't Prof. (ret.)
Univ of Pittsburgh School of Medicine
Department of Pharmacology 1300 BST
Pittsburgh PA 15261 USA
[EMAIL PROTECTED]
Hi, All Chowda Hounds.
What a great time I, er, sorry, we had!
Spent most of Sat the 24th at my wife's 40 High School Reunion, Sheraton
Ferncrroft in Danvers MA. Crawled out of the sack at the crack of 10am.
breakfasted and drove it like I stole it to the town of Gardner and their
Hi, All.
To the Lister who has lost his brass nuts, parallel glow plug type that
is, I have an harness around here somewhere (with attached nuts) and I'll
cut a couple off for you. (Could NOT resist!).
Name and address?
TTFN
Fred Moir
Lynn MA
Yikes!
We are two nations separated by a common language Winston Spencer
Churchill (partial misquote)
Fred Moir
Lynn MA
Dieselitis Maximus
Gregory.
Welcome to the list of people who agree with you 110% !!
Fred Moir
Lynn MA
With 3 diesel Benz on Rusty's life support!
At 09:11 AM 10/14/2005, you wrote:
!RUSTY IS A MAN OF HIS WORD!
!!RUSTY IS A MAN OF HIS WORD!!
!!!RUSTY IS A MAN OF HIS WORD!!!
RUSTY IS A MAN OF HIS
Hi, All.
Local Want AD :- 1987 Mercedes 300 SDL Turbo diesel. Gd motor w/210k mi.
Rusted body. Updated turbo. $250/bo.
(Lynnfield MA) 781 334 2323.
Next town over from me.
Anyone need a 603?
TTFN
Fred Moir.
Lynn MA
Hi, All.
I think my 87 190Dt has a problem and you lot are (collectively) much
smarter than I am. Symptoms:- Small thin ring of oil (?) in the reservoir,
coupled with a very slow loss of coolant. There are no external coolant
leaks visible. I changed the M1 from 15w to 5w (winter's coming)
Hi, All.
There are external easy outs that grip the outside of the bolt that have
worked okay for me. Heat the remains as much as possible and lots of Kroil,
PB Blaster etc., a modicum of luck, and a clean and trouble-free
installation can be yours. I'd also use some anti-seize on the cleaned
Hi, Russ W.
Could you also send info to me? Please. I cannot get it to go either.
TIA
Fred Moir
Lynn MA
Dieselitis Maximus
Kaleb,
Yep there is a trick to it. My Indy has done it and the Secret.
I'll email him and get him to send it to me. I'll relay it to you.
I do know you have to
Russ W.
Murky Buckets. (Ta very much).
TTFN
Fred Moir
Lynn MA
Fred,
I sent it to the List for all.
Russ W.
Hi, All.
On my 87 190Dt, I repaired the leaky EGR with an aluminum gasket about one
eight inch thick. Drew it up on Acad and made a template out of G-10 at
work on the CNC router, then made the gasket. Works real well!
Also used some metal shim seals from Rusty (All Hail Rusty!) 604 142 05
Hi, All.
I'm planning on doing the head gasket (to music wearing funny blue
clothes) on my '87 190DT this weekend and I've a few question to ask about
what i may find:-
1. Turbo oil supply, is it just remove and replace? 'o' rings? No suitable
o-rings in gasket set or midget gaskets either.
Kevin.
Thanks for the info, I have all necessary tools. The hollow cam was a
surprise, will be extra careful.
Fingers and toes crossed. ( to match my eyes!)
TTFN
Fred Moir
Lynn MA
Desel woes, it's always something! (Joan Rivers)
Hi,All.
Just got back from a 2 hour blast up the highway in my '85 300TD. Gee, but
I love this car! Sat for 8 months, blew up tyres, checked fluids, hoses,
belts, etc. etc. and Hi! Ho! Silver! (Blue) and awaaay!
(Must take my downers as I am too high.)
The delete key is you-know-where
Redghost et al.
My 220D heralded all corners with an horn salute! The horn ring
mounting/insulating washer/spacers had crumbled almost to dust. replacing
them fixed my car. YMMV.
Fred Moir
Lynn MA
Hi, All.
After almost 30 years my memory ain't so hot, though I do remember the
horn ring as having a shoulder screw upon which were a wavy washer, a flat
washer and a small insulator, like a top hat with no crown (maybe a small
spring). A fiddley job as I remember. Sorry not to be more
LT.
Amen brother, Amen.
Fred Moir
Lynn MA
Deiselitis Maximus
Hi, All.
My (first) wife had an Olds F85 station wagon with a 330 and a 2 speed, 0
to 70 mph in first, then second, went very fast up to seventy then it
became a bit of a slug. Was young and very foolish those days!
TTFN
Fred Moir
I got too soon old and too late smart.
Hi, All.
My experience with the Mustang replacement O2 sensor in my '85 190E was
excellent. I took a plug /socket from a car in the J/Y and fabricated an
adapter, which I placed inside the passenger seat area under the rug. (
Where the MBZ connector resides.) After having the fuel
Hi, All.
If anyone in the Boston area wants to see a Lister/Blackstone diesel,
there is one in the hospital area as a standby generator, right by the
street with windows to look into. It's across Brookline Ave from the
Deaconess Medical `Annex. One caveat, it was ten years ago that I last saw
to the hospitals in the area. It was put in maybe 20 yr ago?
--R
frederick w moir wrote:
Hi, All.
If anyone in the Boston area wants to see a Lister/Blackstone
diesel,
there is one in the hospital area as a standby generator, right by the
street with windows to look into. It's across Brookline
Hi, All.
Today the weather was fine if cold and I was evaluating the '85 300TD for
a small amount of rust appearing at the pass. lower rear wheel arch, when I
noticed that the fuel tank was dished upwards. Rats! I said (or something
like that!!) The vent is blocked!.
Question:- Can I put some
Thanks, Johhny B.
That's about what I had figured. Regulated supply on hand and waiting for
good weather.
I've had a bath this year and don't need a de-lousing with #2.
Diesel, I mean diesel, yes diesel!
TTFN
Fred Moir
A rose by any other name ..
Fred,
I've gotten away with it
ED,
BTDT, and I am there again, being 63 does not help either!
Fred Moir
Lynn MA
I have only 3 brain cells left and they are pulling double shifts!
ROTFLMAO!!
Cheney with guns not good for older attorneys in Texas. Quayle hunting
was it?
Fred Moir
Lynn MA
Dieselitis Maximus
An honest politician is one who stays bought
(forgot the attribution)
Curt.
Driveshaft for manual
Fred Moir
Lynn MA
190DT Bent
300TD
At 03:45 PM 12/4/2007, you wrote:
I was just thinking about Johnny B the other day. Thinking he'd
ought to be back from his last FEMA thing by now...
He's got (or had anyway) a 190D for Fred, I can't remember what I
wanted off
Hey!
You colonial rabble, I speak English, You have the accents!
An you gotter lurnto spek proppa english, like wot eye do.
Fred, Neo colonial.
Also diesel head
At 08:33 AM 12/6/2007, you wrote:
Not always, I'm from Caribou eh? Living right be the Canadian border
changes the accent
Hi. Giles et al.
Thank you.
I would love an Union Jack badge!
I will of course pay p/p expenses
When asked about it, the answer will be I.m going there to
retire NOT.
Fred Moir
8 mace Place
Lynn MA
01902-3110
Fred,
For some unknown reason, my latest 240d came with a
People of Oel.
It's a corruption of Moor, my people were busy during the crusades,
Killer of Moors.
Pronounced, Hey! You! wit da glassez! or as if it were spelled Moyer.
People will spell it Moyer and I keep telling them, it's a FOUR LETTER WORD!
Yinglish = Moir (Moyer)
Down East = Hey, Fred
Hi, Curt.
Yup I have seen those ads. If I came home with the TD, I'd
go to sleep a baritone and wake up a soprano, and not one of those on TV!
Want it though! I'm just down the road from his place, so near and yet so far.
Fred Moir
Lynn MA
85 300TD
87 190DT Bent
Parking spot for an '87
Curt, et al.
On an '85 190D it isn't too hard to get the starter out, or check the
connections. Apart from the lower bolt the rest is accessible from
the drivers side top, after removing the air filter box complete. A
190E is (was) a lot more difficult as the cruise actuator is in front
of the
Hi, Alles.
Ole Man Winter did it to my HF Portable garage today. Down over the
top of my 300TD. I had just finished with the driveway next door and
mine and had put away the snow blower in the shed, locked up and
turned around, and thought aah s**t!. Much careful shovelling to
free the
Dwight.
Ta, very much
FredMoir
Lynn MA
At 08:08 PM 12/16/2007, you wrote:
I will go look at it and photo it tomorrow or Tuesday. If there is one
thing I know, it is where to look for 123 rust. Will check window seals and
set back lock.
Dwight
Bissell Cove Quahog Auto Salvage Co
Dwight E.
Rusty and Family.
Please accept our deepest condolences.
Another good man gone to his reward.
Joanne and Fred Moir
At 10:22 AM 12/17/2007, you wrote:
While we are all in prayer mode for Kaleb and Regina and their
families, let's add me to the list. My 86 father who had Dementia
for the last 5
Curt, Dwight.
You two are going to be the death of me!
Thanks guys. I had a 220D in 1976 and enjoyed it in my solitary newly
divorced state 1978.
Not the car that I would waste in a NE salt laden winter. Like it though.
Fred Moir
Lynn MA
Diesel deprived.
On Behalf Of Curt Raymond
Sent: Monday,
At 05:55 PM 12/18/2007, you wrote:
I need to replace the OP AMP that is in the climate control for my
1980 300D. The number on it is TAA2765A does anyone know where I can
get a couple of these?
It seems that it locks up.
Thanks.. Douglas
Hi, Douglas.
This opamp seems to be widely used. It
TAA2765A
http://www.icplus.net/frameresults.aspx
Fred Moir
Lynn MA
___
http://www.okiebenz.com
For new parts see official list sponsor: http://www.buymbparts.com/
For used parts email [EMAIL PROTECTED]
To Unsubscribe or change delivery options go to:
So what are the chances that a 602 that broke the chain and broke the
cam does NOT have bent valves? Is is possible that the cam broke
instead of bending a valve? Thinking maybe just replacing cam etc and
seeing what happens without pulling the head. Am I just farting in a
whirlwind?
--
Kaleb
At 12:32 PM 12/31/2007, you wrote:
http://boston.craigslist.org/gbs/car/524215637.html
Seems too cheap
-Curt
Curt et al..
I thought so too. Though it would be nice to have a good one.
Fred Moir
Lynn MA
85 300TD
87 190DT Bent
___
http://www.okiebenz.com
Treasures in the junk pile?
http://cgi.ebay.com/Seagate-ST225-20MB-MFM-Hard-Drive_W0QQitemZ140193434004QQihZ004QQcategoryZ39973QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Fred Moir
Lynn MA
___
http://www.okiebenz.com
For new parts see official list sponsor:
At 01:10 AM 1/2/2008, you wrote:
earlier today, usc killed illinois. they look like the best team in the
country. and georgia just crushed hawaii. i think they are the best team
in the country. missouri really messed up arkansas. looked to me like
maybe they are the best team in the country.
At 11:45 AM 1/2/2008, you wrote:
who decides who is in the playoffs?
Who decides who is best? There must be at least 250 million opinions, not so?
Fred Moir
Lynn MA
___
http://www.okiebenz.com
For new parts see official list sponsor:
At 05:11 PM 1/11/2008, you wrote:
Hi Kevin,
I had a '65 Corvair Corsa 140 convertible (4 carbs/4 speed) Red w/
Black Int. Try as I might, I could not make it Dangerous at any
Speed!!
Loved it!
Chuck
Phoenix AZ
On Jan 11, 2008, at 2:16 PM, Kevin Kraly wrote:
Residual fear of the
Hi, Alles.
Formula Ford has used Cortina engines and they are not slow. Car was
the usual Brit POS and quite zippy. (I know, I'm old)
Fred Moir
Lynn MA
It's Diesel this and Diesel that and chuck 'im out, the brute with
apologies to R. Kipling
At 12:02 PM 1/24/2008, you wrote:
How about the
Happy Birthday Gary!
Fred Moir
Lynn MA
At 06:16 PM 1/24/2008, you wrote:
to pay the county property taxes on my cars (due by my birthday, which is
tomorrow), and i have to say they make it easier and easier all the time.
___
http://www.okiebenz.com
For new
Hi, All.
Following a tip from Dwight of Rhode Island Quahog fame, there is a
companion 190DT next to my bent one. Dwight, I owe you a beer or five!
Had to get up at 4am to beat the other people to it. Very good body
but not perfect, runs on 4 (head gasket), was a bugger to start at 15
deg, only
At 10:30 AM 1/26/2008, you wrote:
Another example of how life is a series of tradeoffs.
Someone please let me know when they have found the perfect place.
Bob R.
Bob et al
Be careful what you wish for!
The grave's a fine and private place, But none, I think, do there embrace.
Andrew Marvell
Fred
To his coy mistress
Had we but world enough, and time
A Marvell.
My wife's romantic response, he just wants to get laid. He's not
proposing marriage.
Fred Moir
Lynn MA
At 11:01 AM 1/26/2008, you wrote:
Good old Andy is correct.
I have not thought of him in quite awhile. He was my high
Bob et al.
Whoever said that they were all sisters was right on the money!
Fred Moir
Lynn MA
85 300TD
87 190DT Bent
87 190DT Blue.
At 11:31 AM 1/27/2008, you wrote:
It appears our wives are related...
Bob R.
___
http://www.okiebenz.com
For new parts see
At 07:58 PM 1/29/2008, you wrote:
Maybe we should discuss my views on ADD and ADHD as diagnosed by doctors.
Please do. My oldest kid has ADHD. I used to think it was a made up
excuse for incorrigible kids. I now know different. I wouldn't wish
ADHD on any parent. It sux.
Rick Knoble
Single
Hi, All.
Car:- 89 260E.
Problem;- How in 'L do I get the old ign. lock out??
Have RTFM and made paper copies to use in the car.
Have made two tools one out of jumbo paper clips and one out of 2mm
(1.92mm) stiff wire.
The paper clip one fits a bit loosely in the slots and the 2mm one
fits in the
At 11:59 AM 1/30/2008, you wrote:
No cure for dieselitis. Maybe no hope.
Dwight E. Giles, Jr.
1978 240D 4 speed. 215K miles.
1979 240D- auto -250K + miles (FOR SALE)
1990 300D 2.5t 150K miles
Wickford, RI
Dwight.
Who said That a cure was needed or required? Dieselitis is fun! Cure
would be
Wilton et al.
After 2 hours of push-pull-turn-jiggle-snarl-cursecursecurse-tweak-
modify tool-make another tool-twist-pray and F**kkit, I gave up.
Obviosly there is more, or less, than meets the eye to this lock
removal trick (?).
Over.
Fred Moir
Lynn MA
With notchy about to fail ign. lock.
Kaleb and Regina.
Congrats on the good news!
Fred Joanne Moir
Lynn MA
___
http://www.okiebenz.com
For new parts see official list sponsor: http://www.buymbparts.com/
For used parts email [EMAIL PROTECTED]
To Unsubscribe or change delivery options go to:
Kaleb.
That is true, however you probably drive in a more restrained manner
which must use less fuel?
Fred Moir
Lynn MA
Public Enema #1
At 01:17 PM 2/7/2008, you wrote:
my 124 2.5 turbo gets that, and its much bigger and smoother probably.
___
At 01:40 PM 2/7/2008, you wrote:
On Feb 7, 2008 10:05 AM, Frederick W Moir [EMAIL PROTECTED] wrote:
My experience
is probably not too typical, I drive either half asleep or too
aggressively
We must have been separated at birth! I'm afraid that describes my
driving perfectly. Must be why I
Hi, Kaleb et al.
190DT 87, have 2, one bent and one responding to tlc. My experience
is probably not too typical, I drive either half asleep or too
aggressively and this is aided and abetted by a car that corners as
if on rails. Goes fast for a 4 door and gets 31/32 mpg on diesel!
(besotted I
Alles.
MacroCrap.
Gives a whole new meaning to Blue Screen of Death.
I hope and pray that all vehicles Don't use it.
Fred Moir
Lynn MA
Dieselitis Maximus.
At 08:56 PM 2/7/2008, you wrote:
If nothing else, the chances that the Linux-based vehicles will crash is
substantially reduced.
Mea culpa, I already apologized to Kaleb, if you want an apology, ask
nicely and I'll have one engraved and hand delivered to you.
NOT!
Fred Moir
Lynn MA
If it were not for the mistakes that I make, I'd have nothing to think about.
At 08:25 PM 6/13/2005, you wrote:
Is this going to be a
Dr Marshall, et al. Thanks for the clarification. This car was in an
accident, sort of repaired, and owned by a diesel mechanic, so the basis
for usual performance is unknown, to me anyway.
TTFN
Fred Moir
Lynn MA
I think I'll call it Shifty
Melissa,
(Definitly non-PC) That's what my wife says!
LOL
Be very careful that you don't add a touch of class to this 'orrible list.
Fred Moir
Lynn MA
Dieselitis Maximus
At 02:44 PM 6/14/2005, you wrote:
Sweet.
Be careful...you'll have everyone asking you to make them one.
I might possibly
Dwight. Did you really mean you are our resident critical philosopher and
comic ? Gad! you must be in need of the glass bridge that I have for sale!
Cheap, can only be seen in direct sunlight. Hurry! Buy NOW!
My wife says that I'm boring and go on too long, (she is of course correct!!)
Later
Hi, All.
I'm about to remove the covers to get at the heater blower motor. Have
RTFM, and the reduced archives, (now moved) and was wondering about
removing the wiper assembly. Specifcally, the rubber seal around the
gearbox that is pinched under the edge of the windshield. I took the
Hi, All.
I offered a paper engine manual (615,616,617.91) in decent condition as a
swap for a working Grand Prix radio, cosmetics not too important and
received an offer of a three way swap, alas no progress. I've tried to buy
one or two Beckers from Ebay, but after reaching my max bid there
3J Combien?
Fred Moir
Lynn MA
4+1 and at the limit.
At 09:10 PM 6/29/2005, you wrote:
you wan a becker outta my '86sdl?...you got money?
___
For used parts email [EMAIL PROTECTED]
For new parts see www.buymbparts.com
For repairs see www.oldworldauto.com
Greetings and salutations JJJ.
For your radio, HOW MUCH? What for shipping?
TIA
Fred Moir
Lynn MA
87 190DT with a UUUgly after market radio.
At 12:21 AM 6/30/2005, you wrote:
what??
3J Combien?
Fred Moir
Lynn MA
4+1 and at the limit.
At 09:10 PM 6/29/2005, you wrote:
you wan
).
On 6/29/05, frederick w moir [EMAIL PROTECTED] wrote:
3J Combien?
Fred Moir
Lynn MA
4+1 and at the limit.
At 09:10 PM 6/29/2005, you wrote:
you wan a becker outta my '86sdl?...you got money?
___
For used parts email [EMAIL PROTECTED]
For new
Joe K.
As they say in real estate, Location, location,location?\
TTFN
Fred Moir
Lynn MA
At 09:30 AM 7/17/2005, you wrote:
From my '87 TD set of 4, 6.5 Jx 15 H2 ET49, tires are 195/65 R 15, 3
Toyo, 1 Michelin X, pretty good tread on the Mich 1 Toyo. Wheels
are nothing to write home
Hi, All.
So, there I was with new front disks, new pads for FR, rebuild kits (just
in case), All Hail Rusty!, Mobil1 grease, having a wonderful time. Next
came flushing the fluid on my 87 190DT, hooked up my trusty Speedi-bleed
and Blooey, Dot 4 everywhere and on Joanne's Toyota too! I did
Klatta Beings,
This is a test to see if I have a brain!
Autocomplete is a nasty thing, sends stuff to (mumble) dot org!
I'm going out to buy a pint of Moose Tracks!
TTFN
Fred Moir
Lynn MA
Hi, All.
As I have no brain, maybe I can get a job at a nuclear power station,
Doh!
Finished my half of the Moose Tracks, maybe me and she who must be obeyed
can start up a weekly ice cream fest!
Have a greasy time.
Fred Moir
Lynn MA
Hi, All.
I just went down to check on my old Uni-Syn, seems to be gone. To use a
sync tool on a carb. that has no clear access, use a short piece of large
rubber hose the size of the carb. neck between the carb and tool. If I find
the Uni-Syn I'll let you know.
TTFN
Fred Moir
Lynn MA
87
Hi, All.
Home with a sore jaw from the dentist's tender mercies, The pain killers
had me flying, so, when my feet touched down, it was off to the
Junkyard! (therapy)
I scavenged a Black book parts catalog for 450SE/SEL 116 1972 U.S. Version.
Free for the asking. There was nothing for me at
Hi, All.
Synapse fired at the no torque/stalls. I had a BMW 1600 with (unknown
to me!) bad points, that would start right up hot or cold and then die the
moment that you touched the throttle. Could our esteemed colleague have
poor ignition? Just my $0.02 worth, maybe even worthless. Never
Hi, All. Reply to Don Roberto. When I replaced the shutoff vacuum pukky, I
first got a replacement from Rusty (All Hail Rusty!), removed the intake
manifold, (new gasket same source) tried not to break anything removing the
electrical connector. The locking ring for the conn. came off after
1 - 100 of 679 matches
Mail list logo