As Tom mentioned (Thank you), with the current hardware there is no additional memory is available to toggle the two firmware setup. There shouldn't be any problem using 0.09 firmware on the airbridge(with old chip) units. Have you tried using 0.09 firmware on this units? If you have any issues, please write to [EMAIL PROTECTED] for the further assistance.
Seeni sB Tech Support [EMAIL PROTECTED] -----Original Message----- From: Tom Haynes [mailto:[EMAIL PROTECTED] Sent: Friday, September 05, 2003 2:19 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Backhaul with Air bridge. It is technicaly possible but there in no room for two setups in the flash memory. The only way to change the op mode of an AB is to change load sifferent firmware. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Billy Huddleston Sent: Thursday, September 04, 2003 4:02 PM To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Backhaul with Air bridge. Could you all not have a toggle in the newer firmware that would allow you to go to single-mac transparent bridging? I mean, the AirBridges with the chip problem won't be able to run the older firmware... ----- Original Message ----- From: "sB Tech Support" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Thursday, September 04, 2003 4:54 PM Subject: RE: [smartBridges] Backhaul with Air bridge. > If the airBridge is connected directly to the router and with old > firmware (transparent bridge), this will work. > > Please refer to this FAQ > http://www.smartbridges.com/new/support/faq_ab.php#155 > > Alex > sB Tech Support > [EMAIL PROTECTED] > > > -----Original Message----- > From: Rudolph Worrell [mailto:[EMAIL PROTECTED] > Sent: Friday, September 05, 2003 4:42 AM > To: [EMAIL PROTECTED] > Subject: Re: [smartBridges] Backhaul with Air bridge. > > I had the same question and was told that this: > > "Is it advisable to use aPPO in client bridge mode at the base station. > If > you want to use airBridge, then it has to connect to a router with > transparent bridge firmware. Because airBridge with newer firmware, it > does Mac translation, so you can't pass traffic to internet in that > setup. " > > So this setup is preferred: > Base Station----aPPO (CB)-----------aPPO (AP)----------Wireless clients. > > > With this, it is transparent bridge and can support multimac. > > Alex > sB Tech Support > [EMAIL PROTECTED] > > In theory I think this is fine because the Airbridge at the customer > recive and > send information to the internet. > > I think that you can connect the Airbridge to the router or > switch>>>connect > using wireless to the APP0 and have our customers connect to that APPO > using > wireless. > > (wired)router>>>Airbridge>>>>APPO>>>Customers using Airbridge indoor or > > outdoor. > > Is this what you did? > > > > -- > Rudolph Worrell > President > Phone:(540)664-3950 > Fax:(270)458-6431 > www.wave2net.com > > > Quoting Pascal Losier <[EMAIL PROTECTED]>: > > > According to smartbridges, we can't do backhaul with an airbridge. > > > > For some reason Im testing with an Airbridge & it works ! > > > > I only hook up tree custumer with this wipop. > > > > Apparently, Airbridge is not transparent bridge like an APP. > > > > > > > > Why is it working ??? Im afraid to deploy with an airbridge,,, > > > > Maybe I should look for another CPE for backhaul. > > > > > > > ------------------------------------------------- > This mail sent through IMP: http://horde.org/imp/ > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges > <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > ÿÿÿÿÿÿÿð 4å C5?ÿÿÿÿÿÿÿ ‰ÿµú+ëm¢· ŠË^ú+X„ãHVm§ÿÿà ÿÂ+)r‰ÿŠwèþë?Â+)r‰ÿŠÿðŠÊ\¢â¿øm™8^<Sÿ^ÿ9¬™ªí¸ëŠÇ.²È¨œ¸¬µ: ¢)ÿ™¨¥¶â™¨¥²»ÿ¥ªíÿ^ÿ¢¸ÿŠ{ayº ÊÜ©zË›±Êâmë&j»A®'`zÏò¢êç‰É'jgÿN„^š‹Þþf¢–ÚÿŠf¢–Êïþ–«·ýyþŠàþ)í…æèw+r¥ë§²æìr¸›zÉš®Ðk‰Ø ³ð+r¯zÏá¶Úÿÿö«r¯zÏéj»ÿןè ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
