hi,
yes i can log via SSH but just when i hit in the command prompt
"boot>" the instruction of the boot.conf file, if i do nothing the
system hangs .
comBIOS ver. 1.32i 20071005 Copyright (C) 2000-2007 Soekris Engineering.
net5501
0512 Mbyte Memory CPU Geode LX 500 Mhz
Pri Sla SMC512AFB6E LBA 1014-16-63 511 Mbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15
0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15
1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 pci mem[639K 511M a20=on]
disk: hd0+
>> OpenBSD/i386 BOOT 3.02
switching console to com0
>> OpenBSD/i386 BOOT 3.02
boot> stty com0 19200
com0: 19200 baud
boot> set tty com0
switching console to com0
>> OpenBSD/i386 BOOT 3.02
boot> boot bsd.rd
booting hd0a:bsd.rd: 5651156+913072 [52+211008+196339]=0x6a6260
entry point at 0x200120
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2009 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.6 (RAMDISK_CD) #53: Thu Jul 9 21:41:35 MDT 2009
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500 M
.....
bios0 at mainbus0: AT/286+ BIOS, date 20/71/05, BIOS32 rev. 0 @ 0xfac40
.....
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
.......
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/i386 4.6 installation program.
(I)nstall, (U)pgrade or (S)hell? S
# ls
.profile etc install.sub sbin usr
bin install mnt tmp var
dev install.md mnt2 upgrade
#
2009/12/29, Bill Maas <[email protected]>:
> Hi Aniss,
>
> I don't think the order of the stty and set command matters a lot.
> Just don't place the boot command in top, or they never will be
> executed. Did you activate serial output in /etc/ttys? That's the only
> other trivial thing I can come up with. A non-trivial thing would be the
> boot loader not being able to correctly parse /etc/boot.conf for some
> reason and load the kernel using default settings, but so far I've never
> seen that happen, and you probably would get an error message in that
> case. It MUST be the kernel serial port setup somewhere, since
> everything else goes according to plan. Can you log in over SSH?
>
> Bill
>
> On Tue, 2009-12-29 at 14:26 +0100, aniss siyouti wrote:
>> Hi Bill ,
>>
>> I checked the order of the boot commands in boot.conf and i noticed
>> that is different from the order in the document
>> my boot.conf :
>>
>> set tty com0
>>
>> stty com0 19200
>>
>> boot tftp:/bsd.rd
>>
>>
>>
>> the correct order :
>>
>> stty com0 19200
>>
>> set tty com0
>>
>> boot tftp:/bsd.rd
>>
>> i tried to reprogram my soekris box using pxebooting but my system
>> hang again after the same message,I’m apparently unlucky;
>> aniss
>>
>>
>>
>> 2009/12/28 Bill Maas <[email protected]>
>> Hi Aniss,
>>
>> I sent the previous message prematurely, so let's finish it.
>> The text
>> comes from the doc I pointed you to. Your Soekris box is
>> probably
>> booting just fine, you just don't get to witness it;).
>>
>> Bill
>>
>>
>> On Mon, 2009-12-28 at 11:58 +0000, aniss siyouti wrote:
>>
>> > thank you all it works , i installed the packages using
>> local ftp
>> > server.
>> > but i have another problem,when i reboot my soekris,The
>> cursor stops
>> > at the following line :
>> > "boot> booting hd0a:/bsd: 6563548+1052072=0x7435f8
>> > entry point at 0x200120"
>> > i have changed the boot order, why it always booting on the
>> hd?
>> >
>> > ............
>> > > show
>> >
>> > ConSpeed = 19200
>> > ConLock = Enabled
>> > ConMute = Disabled
>> > BIOSentry = Enabled
>> > PCIROMS = Enabled
>> > PXEBoot = Enabled
>> > FLASH = Primary
>> > BootDelay = 5
>> > FastBoot = Disabled
>> > BootPartition = Disabled
>> > BootDrive = 80 81 F0 FF
>> > ShowPCI = Enabled
>> > Reset = Hard
>> > ..............
>> >
>> > Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2
>> Int
>> >
>>
>> -------------------------------------------------------------------
>> > 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000
>> 00000000 10
>> > 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101
>> A0004000 11
>> > 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201
>> A0004100 05
>> > 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301
>> A0004200 09
>> > 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401
>> A0004300 12
>> > 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001
>> 00006101
>> > 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000
>> 00000000
>> > 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000
>> 00000000 15
>> > 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000
>> 00000000 15
>> >
>> > 1 Seconds to automatic boot. Press Ctrl-P for entering
>> Monitor.
>> > Using drive 0, partition 3.
>> > Loading...
>> > probing: pc0 com0 com1 pci mem[639K 511M a20=on]
>> > disk: hd0+
>> > >> OpenBSD/i386 BOOT 3.02
>> > switching console to com0
>> > >> OpenBSD/i386 BOOT 3.02
>> > boot>
>> > booting hd0a:/bsd: 6563548+1052072=0x7435f8
>> > entry point at 0x200120
>> >
>> >
>>
>> > _______________________________________________
>> > Soekris-tech mailing list
>> > [email protected]
>> > http://lists.soekris.com/mailman/listinfo/soekris-tech
>>
>>
>>
>>
>>
>
>
>
_______________________________________________
Soekris-tech mailing list
[email protected]
http://lists.soekris.com/mailman/listinfo/soekris-tech
