Hi, I also have the same problem since Novembre 2009, I have bought three ScanDisk CF but OpenBSD does not succeed to boot. I have tried this recommanded card by Soekris.
- *ScanDisk Ultra II CompactFlash 15MB/s 8GB (==> Freezes at boot)* - *Scandisk Extreme CompactFlash 60MB/s 8GB (==> Freezes at boot)* - *Scandisk Extreme III 30MB/s 8GB ( OpenBSD 4.6 also freezes at boot)* I have got this type of messages and freezes : *1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.* *Using drive 0, partition 3.* *Loading...* *probing: pc0 com0 com1 pci mem[639K 511M a20=on]* *disk: hd0+* *>> OpenBSD/i386 BOOT 3.02* *boot>* *booting hd0a:/bsd: 6563548+1052072 [52+345584+327881]=0x7e7ce8* *entry point at 0x200120* Any idea ? Thanks in advance HB 2009/12/31 Bill Maas <[email protected]> > Hi Aniss, > > in your previous post you got this: > > boot> > booting hd0a:/bsd: 6563548+1052072=0x7435f8 > entry point at 0x200120 > > Followed by {void}. Note that here boot.conf has been parsed and the > kernel image has been loaded. This would in most cases indicate a system > booting with the wrong output parameters. > > But you're right, it can also point at a system that simply hangs. > Interesting question is why it then doesn't if you enter the boot > parameters manually. Perhaps better consult the OpenBSD misc list. > > I hope I understand you well, posting the output of a bsd.rd boot as > well doesn't make things clearer.. (that's a totally different story). > > Warning about the misc list in case you're not familiar with it: always > post at least a full dmesg, and show lots of respect for the project - > they bark a lot there but they bite as well:) > > Good luck, > > Bill > > > On Thu, 2009-12-31 at 13:52 +0000, aniss siyouti wrote: > > hi, > > yes i can log via SSH but just when i hit in the command prompt > > "boot>" the instruction of the boot.conf file, if i do nothing the > > system hangs . > > > > comBIOS ver. 1.32i 20071005 Copyright (C) 2000-2007 Soekris Engineering. > > > > net5501 > > > > 0512 Mbyte Memory CPU Geode LX 500 Mhz > > > > Pri Sla SMC512AFB6E LBA 1014-16-63 511 Mbyte > > > > Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int > > ------------------------------------------------------------------- > > 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10 > > 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11 > > 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05 > > 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09 > > 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12 > > 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101 > > 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000 > > 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15 > > 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15 > > > > 1 Seconds to automatic boot. Press Ctrl-P for entering Monitor. > > Using drive 0, partition 3. > > Loading... > > probing: pc0 com0 com1 pci mem[639K 511M a20=on] > > disk: hd0+ > > >> OpenBSD/i386 BOOT 3.02 > > switching console to com0 > > >> OpenBSD/i386 BOOT 3.02 > > boot> stty com0 19200 > > > > com0: 19200 baud > > boot> set tty com0 > > switching console to com0 > > >> OpenBSD/i386 BOOT 3.02 > > boot> boot bsd.rd > > booting hd0a:bsd.rd: 5651156+913072 [52+211008+196339]=0x6a6260 > > entry point at 0x200120 > > > > Copyright (c) 1982, 1986, 1989, 1991, 1993 > > The Regents of the University of California. All rights > reserved. > > Copyright (c) 1995-2009 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > > > OpenBSD 4.6 (RAMDISK_CD) #53: Thu Jul 9 21:41:35 MDT 2009 > > [email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD > > cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" > 586-class) 500 M > > ..... > > bios0 at mainbus0: AT/286+ BIOS, date 20/71/05, BIOS32 rev. 0 @ 0xfac40 > > ..... > > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > > com0: console > > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > > ....... > > erase ^?, werase ^W, kill ^U, intr ^C, status ^T > > > > Welcome to the OpenBSD/i386 4.6 installation program. > > (I)nstall, (U)pgrade or (S)hell? S > > # ls > > .profile etc install.sub sbin usr > > bin install mnt tmp var > > dev install.md mnt2 upgrade > > # > > > > 2009/12/29, Bill Maas <[email protected]>: > > > Hi Aniss, > > > > > > I don't think the order of the stty and set command matters a lot. > > > Just don't place the boot command in top, or they never will be > > > executed. Did you activate serial output in /etc/ttys? That's the only > > > other trivial thing I can come up with. A non-trivial thing would be > the > > > boot loader not being able to correctly parse /etc/boot.conf for some > > > reason and load the kernel using default settings, but so far I've > never > > > seen that happen, and you probably would get an error message in that > > > case. It MUST be the kernel serial port setup somewhere, since > > > everything else goes according to plan. Can you log in over SSH? > > > > > > Bill > > > > > > On Tue, 2009-12-29 at 14:26 +0100, aniss siyouti wrote: > > >> Hi Bill , > > >> > > >> I checked the order of the boot commands in boot.conf and i noticed > > >> that is different from the order in the document > > >> my boot.conf : > > >> > > >> set tty com0 > > >> > > >> stty com0 19200 > > >> > > >> boot tftp:/bsd.rd > > >> > > >> > > >> > > >> the correct order : > > >> > > >> stty com0 19200 > > >> > > >> set tty com0 > > >> > > >> boot tftp:/bsd.rd > > >> > > >> i tried to reprogram my soekris box using pxebooting but my system > > >> hang again after the same message,I’m apparently unlucky; > > >> aniss > > >> > > >> > > >> > > >> 2009/12/28 Bill Maas <[email protected]> > > >> Hi Aniss, > > >> > > >> I sent the previous message prematurely, so let's finish it. > > >> The text > > >> comes from the doc I pointed you to. Your Soekris box is > > >> probably > > >> booting just fine, you just don't get to witness it;). > > >> > > >> Bill > > >> > > >> > > >> On Mon, 2009-12-28 at 11:58 +0000, aniss siyouti wrote: > > >> > > >> > thank you all it works , i installed the packages using > > >> local ftp > > >> > server. > > >> > but i have another problem,when i reboot my soekris,The > > >> cursor stops > > >> > at the following line : > > >> > "boot> booting hd0a:/bsd: 6563548+1052072=0x7435f8 > > >> > entry point at 0x200120" > > >> > i have changed the boot order, why it always booting on the > > >> hd? > > >> > > > >> > ............ > > >> > > show > > >> > > > >> > ConSpeed = 19200 > > >> > ConLock = Enabled > > >> > ConMute = Disabled > > >> > BIOSentry = Enabled > > >> > PCIROMS = Enabled > > >> > PXEBoot = Enabled > > >> > FLASH = Primary > > >> > BootDelay = 5 > > >> > FastBoot = Disabled > > >> > BootPartition = Disabled > > >> > BootDrive = 80 81 F0 FF > > >> > ShowPCI = Enabled > > >> > Reset = Hard > > >> > .............. > > >> > > > >> > Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 > > >> Int > > >> > > > >> > > >> ------------------------------------------------------------------- > > >> > 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 > > >> 00000000 10 > > >> > 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 > > >> A0004000 11 > > >> > 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 > > >> A0004100 05 > > >> > 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 > > >> A0004200 09 > > >> > 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 > > >> A0004300 12 > > >> > 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 > > >> 00006101 > > >> > 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 > > >> 00000000 > > >> > 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 > > >> 00000000 15 > > >> > 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 > > >> 00000000 15 > > >> > > > >> > 1 Seconds to automatic boot. Press Ctrl-P for entering > > >> Monitor. > > >> > Using drive 0, partition 3. > > >> > Loading... > > >> > probing: pc0 com0 com1 pci mem[639K 511M a20=on] > > >> > disk: hd0+ > > >> > >> OpenBSD/i386 BOOT 3.02 > > >> > switching console to com0 > > >> > >> OpenBSD/i386 BOOT 3.02 > > >> > boot> > > >> > booting hd0a:/bsd: 6563548+1052072=0x7435f8 > > >> > entry point at 0x200120 > > >> > > > >> > > > >> > > >> > _______________________________________________ > > >> > Soekris-tech mailing list > > >> > [email protected] > > >> > http://lists.soekris.com/mailman/listinfo/soekris-tech > > >> > > >> > > >> > > >> > > >> > > > > > > > > > > > _______________________________________________ > > Soekris-tech mailing list > > [email protected] > > http://lists.soekris.com/mailman/listinfo/soekris-tech > > > > > _______________________________________________ > Soekris-tech mailing list > [email protected] > http://lists.soekris.com/mailman/listinfo/soekris-tech >
_______________________________________________ Soekris-tech mailing list [email protected] http://lists.soekris.com/mailman/listinfo/soekris-tech
