Hi Aniss,
in your previous post you got this:
boot>
booting hd0a:/bsd: 6563548+1052072=0x7435f8
entry point at 0x200120
Followed by {void}. Note that here boot.conf has been parsed and the
kernel image has been loaded. This would in most cases indicate a system
booting with the wrong output parameters.
But you're right, it can also point at a system that simply hangs.
Interesting question is why it then doesn't if you enter the boot
parameters manually. Perhaps better consult the OpenBSD misc list.
I hope I understand you well, posting the output of a bsd.rd boot as
well doesn't make things clearer.. (that's a totally different story).
Warning about the misc list in case you're not familiar with it: always
post at least a full dmesg, and show lots of respect for the project -
they bark a lot there but they bite as well:)
Good luck,
Bill
On Thu, 2009-12-31 at 13:52 +0000, aniss siyouti wrote:
> hi,
> yes i can log via SSH but just when i hit in the command prompt
> "boot>" the instruction of the boot.conf file, if i do nothing the
> system hangs .
>
> comBIOS ver. 1.32i 20071005 Copyright (C) 2000-2007 Soekris Engineering.
>
> net5501
>
> 0512 Mbyte Memory CPU Geode LX 500 Mhz
>
> Pri Sla SMC512AFB6E LBA 1014-16-63 511 Mbyte
>
> Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
> -------------------------------------------------------------------
> 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
> 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
> 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
> 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
> 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
> 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
> 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
> 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15
> 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15
>
> 1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
> Using drive 0, partition 3.
> Loading...
> probing: pc0 com0 com1 pci mem[639K 511M a20=on]
> disk: hd0+
> >> OpenBSD/i386 BOOT 3.02
> switching console to com0
> >> OpenBSD/i386 BOOT 3.02
> boot> stty com0 19200
>
> com0: 19200 baud
> boot> set tty com0
> switching console to com0
> >> OpenBSD/i386 BOOT 3.02
> boot> boot bsd.rd
> booting hd0a:bsd.rd: 5651156+913072 [52+211008+196339]=0x6a6260
> entry point at 0x200120
>
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2009 OpenBSD. All rights reserved. http://www.OpenBSD.org
>
> OpenBSD 4.6 (RAMDISK_CD) #53: Thu Jul 9 21:41:35 MDT 2009
> [email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
> cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
> 500 M
> .....
> bios0 at mainbus0: AT/286+ BIOS, date 20/71/05, BIOS32 rev. 0 @ 0xfac40
> .....
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> .......
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/i386 4.6 installation program.
> (I)nstall, (U)pgrade or (S)hell? S
> # ls
> .profile etc install.sub sbin usr
> bin install mnt tmp var
> dev install.md mnt2 upgrade
> #
>
> 2009/12/29, Bill Maas <[email protected]>:
> > Hi Aniss,
> >
> > I don't think the order of the stty and set command matters a lot.
> > Just don't place the boot command in top, or they never will be
> > executed. Did you activate serial output in /etc/ttys? That's the only
> > other trivial thing I can come up with. A non-trivial thing would be the
> > boot loader not being able to correctly parse /etc/boot.conf for some
> > reason and load the kernel using default settings, but so far I've never
> > seen that happen, and you probably would get an error message in that
> > case. It MUST be the kernel serial port setup somewhere, since
> > everything else goes according to plan. Can you log in over SSH?
> >
> > Bill
> >
> > On Tue, 2009-12-29 at 14:26 +0100, aniss siyouti wrote:
> >> Hi Bill ,
> >>
> >> I checked the order of the boot commands in boot.conf and i noticed
> >> that is different from the order in the document
> >> my boot.conf :
> >>
> >> set tty com0
> >>
> >> stty com0 19200
> >>
> >> boot tftp:/bsd.rd
> >>
> >>
> >>
> >> the correct order :
> >>
> >> stty com0 19200
> >>
> >> set tty com0
> >>
> >> boot tftp:/bsd.rd
> >>
> >> i tried to reprogram my soekris box using pxebooting but my system
> >> hang again after the same message,I’m apparently unlucky;
> >> aniss
> >>
> >>
> >>
> >> 2009/12/28 Bill Maas <[email protected]>
> >> Hi Aniss,
> >>
> >> I sent the previous message prematurely, so let's finish it.
> >> The text
> >> comes from the doc I pointed you to. Your Soekris box is
> >> probably
> >> booting just fine, you just don't get to witness it;).
> >>
> >> Bill
> >>
> >>
> >> On Mon, 2009-12-28 at 11:58 +0000, aniss siyouti wrote:
> >>
> >> > thank you all it works , i installed the packages using
> >> local ftp
> >> > server.
> >> > but i have another problem,when i reboot my soekris,The
> >> cursor stops
> >> > at the following line :
> >> > "boot> booting hd0a:/bsd: 6563548+1052072=0x7435f8
> >> > entry point at 0x200120"
> >> > i have changed the boot order, why it always booting on the
> >> hd?
> >> >
> >> > ............
> >> > > show
> >> >
> >> > ConSpeed = 19200
> >> > ConLock = Enabled
> >> > ConMute = Disabled
> >> > BIOSentry = Enabled
> >> > PCIROMS = Enabled
> >> > PXEBoot = Enabled
> >> > FLASH = Primary
> >> > BootDelay = 5
> >> > FastBoot = Disabled
> >> > BootPartition = Disabled
> >> > BootDrive = 80 81 F0 FF
> >> > ShowPCI = Enabled
> >> > Reset = Hard
> >> > ..............
> >> >
> >> > Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2
> >> Int
> >> >
> >>
> >> -------------------------------------------------------------------
> >> > 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000
> >> 00000000 10
> >> > 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101
> >> A0004000 11
> >> > 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201
> >> A0004100 05
> >> > 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301
> >> A0004200 09
> >> > 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401
> >> A0004300 12
> >> > 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001
> >> 00006101
> >> > 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000
> >> 00000000
> >> > 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000
> >> 00000000 15
> >> > 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000
> >> 00000000 15
> >> >
> >> > 1 Seconds to automatic boot. Press Ctrl-P for entering
> >> Monitor.
> >> > Using drive 0, partition 3.
> >> > Loading...
> >> > probing: pc0 com0 com1 pci mem[639K 511M a20=on]
> >> > disk: hd0+
> >> > >> OpenBSD/i386 BOOT 3.02
> >> > switching console to com0
> >> > >> OpenBSD/i386 BOOT 3.02
> >> > boot>
> >> > booting hd0a:/bsd: 6563548+1052072=0x7435f8
> >> > entry point at 0x200120
> >> >
> >> >
> >>
> >> > _______________________________________________
> >> > Soekris-tech mailing list
> >> > [email protected]
> >> > http://lists.soekris.com/mailman/listinfo/soekris-tech
> >>
> >>
> >>
> >>
> >>
> >
> >
> >
> _______________________________________________
> Soekris-tech mailing list
> [email protected]
> http://lists.soekris.com/mailman/listinfo/soekris-tech
>
_______________________________________________
Soekris-tech mailing list
[email protected]
http://lists.soekris.com/mailman/listinfo/soekris-tech
