----- Original Message ----- From: "eric tanguy" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Sunday, May 16, 2004 11:05 AM Subject: [speedtouch] Re: Problem USB and SPEEDTOUCH
> > > You need the zzzlp(x) serie with Rev 4.00 > > modem_run -v 1 -t 90 -n 4 -f /usr/share/speedtouch/firmware.ZZZLP1.eni > > -a /usr/share/speedtouch/boot.ZZZLP2.eni > > -v 1 display nice informations > > -n 4 is enough attempt to load firmware > > -t 90 avoid to wait to much if you ADSL is brocken, you reboot and your > > connection start automaticaly at boot. > > If you use the kernel driver, you need to : > > - modprobe speedtch > > - run modem_run with adding -k to other options > > - sleep 5 > > I am not usin hotplug, so I don't know to much how it should work. > > I'm not sure to well understand > I can't find firmware.ZZZLP1.eni and boot.ZZZLP2.eni but i found > ZZZLP1.eni and ZZZLP2.eni on my winxp and i copied them in > /usr/local/share/speedtouch/ > and i ran modem_run -v 1 -t 90 -n 4 -f > /usr/local/share/speedtouch/zzzlp1.eni -a > /usr/local/share/speedtouch/zzzlp2.eni > You said that i have to reboot and my connection would start automatically ? I don't know for you . I am not using hotplug nor startadsl Shelte Bron is right: -a is for 1.eni and -f is for 2.eni with -v 1, you should have seen if modem_run care about the mismatch. > I tried it but it didn't work. > So I tried to follow the french howto : > I ran modem_run -v 1 -t 90 -n 4 -f /usr/local/share/speedtouch/zzzlp1.eni > -a /usr/local/share/speedtouch/zzzlp2.eni > and > pppd call adsl updetach > and i had these messages : > using channel 1 > Using interface ppp0 > Connect: ppp0 <--> /dev/pts/2 > Modem hangup > Connection terminated. > using channel 2 > Using interface ppp0 > Connect: ppp0 <--> /dev/pts/2 > Script /usr/local/sbin/pppoa3 -m 1 -c -vpi 8 -vci 35 finished (pid 10565), > status = 0xff > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x35ad9cc3>] > LCP: timeout sending Config-Requests Try to add in you option file lcp-max-configure 50 the default time of 30 s may be too short for slow BAS. I often wait 11 time so (3*11=33s) before to receive the first answer. Liste de diffusion modem ALCATEL SpeedTouch USB Pour se d�sinscrire : mailto:[EMAIL PROTECTED]
