the lane for the bus bay is only 12m long. You'll have to set your stop position within that range.
Am Fr., 29. Apr. 2022 um 22:34 Uhr schrieb ali mirzaei <[email protected] >: > I did what you said in my opinion but at the beginning of the simulation I > faced the error : stop for vehicle 'bus_1' on lane 'e2_0' has an invalid > position. Could you tell me what mistakes I have made? (I have attached my > files for possible information required) > > > On Fri, Apr 29, 2022 at 3:16 PM Jakob Erdmann <[email protected]> > wrote: > >> The extra lane should only be as long as the bus bay and you'd typically >> need to split the original edge into 3 parts to achieve this. >> >> Am Fr., 29. Apr. 2022 um 12:37 Uhr schrieb ali mirzaei < >> [email protected]>: >> >>> I added an extra lane and used it as a bus stop at the specified >>> coordinates but before getting there, the bus makes a lane change from the >>> upstream (which is not desired) and after the end of the stop period, it >>> moves in the extra lane and no longer backs to its primary lane (which is >>> not desired, too). >>> >>> On Fri, Apr 29, 2022 at 10:32 AM Jakob Erdmann <[email protected]> >>> wrote: >>> >>>> 1. if a vehicle stops with attribute parking="true", it no longer >>>> records emissions (up to the time where the stop ends and it tries to >>>> re-enter the network) >>>> 2. if a vehicle returns from the "parking" state, road traffic will >>>> generally not be are of it's wish to re-enter the road and thus not open a >>>> gap >>>> >>>> Both issues can be solved by modelling each bus bay with an extra lane >>>> and having the bus stay on that lane during it's stop. >>>> >>>> Am Fr., 29. Apr. 2022 um 00:15 Uhr schrieb ali mirzaei < >>>> [email protected]>: >>>> >>>>> Hi everyone, >>>>> Using the ~.setStop() method, my buses start performing station >>>>> operations where they were previously assigned. The emission class is >>>>> "HBEFA3/PC_G_EU4". >>>>> 1 - After observing some irregularities in the emission curves, I >>>>> evaluated the emission outputs and found that at the moment the vehicle >>>>> arrived at the station, the whole emission attributes turned to zero and >>>>> after that no data of the vehicle was recorded for the duration length. >>>>> This process stops when the vehicle leaves the station and the pollution >>>>> information is recorded again. Why does this happen? >>>>> 2 - When I add more vehicles to the road to simulate the rush hour >>>>> effect on the operation, the merging of the bus would not happen in the >>>>> determined period. How can I fix it? >>>>> Best regards, >>>>> Ali >>>>> >>>>> _______________________________________________ >>>>> sumo-user mailing list >>>>> [email protected] >>>>> To unsubscribe from this list, visit >>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>> >>>> _______________________________________________ >>>> sumo-user mailing list >>>> [email protected] >>>> To unsubscribe from this list, visit >>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>> >>> _______________________________________________ >>> sumo-user mailing list >>> [email protected] >>> To unsubscribe from this list, visit >>> https://www.eclipse.org/mailman/listinfo/sumo-user >>> >> _______________________________________________ >> sumo-user mailing list >> [email protected] >> To unsubscribe from this list, visit >> https://www.eclipse.org/mailman/listinfo/sumo-user >> > _______________________________________________ > sumo-user mailing list > [email protected] > To unsubscribe from this list, visit > https://www.eclipse.org/mailman/listinfo/sumo-user >
_______________________________________________ sumo-user mailing list [email protected] To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-user
