startPos and pos must be in the range [0, 12] to stop on that edge. The values always count from the start of the stop edge.
Am Sa., 30. Apr. 2022 um 00:45 Uhr schrieb ali mirzaei <[email protected] >: > I think I did so, didn't I? > My startPos = 112.19 and the pos = 124.49 > > On Sat, Apr 30, 2022 at 2:31 AM Jakob Erdmann <[email protected]> > wrote: > >> the lane for the bus bay is only 12m long. You'll have to set your stop >> position within that range. >> >> Am Fr., 29. Apr. 2022 um 22:34 Uhr schrieb ali mirzaei < >> [email protected]>: >> >>> I did what you said in my opinion but at the beginning of the simulation >>> I faced the error : stop for vehicle 'bus_1' on lane 'e2_0' has an invalid >>> position. Could you tell me what mistakes I have made? (I have attached my >>> files for possible information required) >>> >>> >>> On Fri, Apr 29, 2022 at 3:16 PM Jakob Erdmann <[email protected]> >>> wrote: >>> >>>> The extra lane should only be as long as the bus bay and you'd >>>> typically need to split the original edge into 3 parts to achieve this. >>>> >>>> Am Fr., 29. Apr. 2022 um 12:37 Uhr schrieb ali mirzaei < >>>> [email protected]>: >>>> >>>>> I added an extra lane and used it as a bus stop at the specified >>>>> coordinates but before getting there, the bus makes a lane change from the >>>>> upstream (which is not desired) and after the end of the stop period, it >>>>> moves in the extra lane and no longer backs to its primary lane (which is >>>>> not desired, too). >>>>> >>>>> On Fri, Apr 29, 2022 at 10:32 AM Jakob Erdmann <[email protected]> >>>>> wrote: >>>>> >>>>>> 1. if a vehicle stops with attribute parking="true", it no longer >>>>>> records emissions (up to the time where the stop ends and it tries to >>>>>> re-enter the network) >>>>>> 2. if a vehicle returns from the "parking" state, road traffic will >>>>>> generally not be are of it's wish to re-enter the road and thus not open >>>>>> a >>>>>> gap >>>>>> >>>>>> Both issues can be solved by modelling each bus bay with an extra >>>>>> lane and having the bus stay on that lane during it's stop. >>>>>> >>>>>> Am Fr., 29. Apr. 2022 um 00:15 Uhr schrieb ali mirzaei < >>>>>> [email protected]>: >>>>>> >>>>>>> Hi everyone, >>>>>>> Using the ~.setStop() method, my buses start performing station >>>>>>> operations where they were previously assigned. The emission class is >>>>>>> "HBEFA3/PC_G_EU4". >>>>>>> 1 - After observing some irregularities in the emission curves, I >>>>>>> evaluated the emission outputs and found that at the moment the vehicle >>>>>>> arrived at the station, the whole emission attributes turned to zero and >>>>>>> after that no data of the vehicle was recorded for the duration length. >>>>>>> This process stops when the vehicle leaves the station and the pollution >>>>>>> information is recorded again. Why does this happen? >>>>>>> 2 - When I add more vehicles to the road to simulate the rush hour >>>>>>> effect on the operation, the merging of the bus would not happen in the >>>>>>> determined period. How can I fix it? >>>>>>> Best regards, >>>>>>> Ali >>>>>>> >>>>>>> _______________________________________________ >>>>>>> sumo-user mailing list >>>>>>> [email protected] >>>>>>> To unsubscribe from this list, visit >>>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>>> >>>>>> _______________________________________________ >>>>>> sumo-user mailing list >>>>>> [email protected] >>>>>> To unsubscribe from this list, visit >>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>> >>>>> _______________________________________________ >>>>> sumo-user mailing list >>>>> [email protected] >>>>> To unsubscribe from this list, visit >>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>> >>>> _______________________________________________ >>>> sumo-user mailing list >>>> [email protected] >>>> To unsubscribe from this list, visit >>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>> >>> _______________________________________________ >>> sumo-user mailing list >>> [email protected] >>> To unsubscribe from this list, visit >>> https://www.eclipse.org/mailman/listinfo/sumo-user >>> >> _______________________________________________ >> sumo-user mailing list >> [email protected] >> To unsubscribe from this list, visit >> https://www.eclipse.org/mailman/listinfo/sumo-user >> > _______________________________________________ > sumo-user mailing list > [email protected] > To unsubscribe from this list, visit > https://www.eclipse.org/mailman/listinfo/sumo-user >
_______________________________________________ sumo-user mailing list [email protected] To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-user
