> You can change the junction type where the bus bay ends to "zipper" to ensure that the bus can merge. When I change the connection type to "zipper", other vehicles that used to move the side lane also enter the bus bay as shown in the attached picture. Trying to fix this by using "allow = bus" attribute for the bus bay, I faced another error says : " Vehicle 'bus_1' is not allowed to stop on lane 'e2_0'." [image: image.png]
On Mon, May 2, 2022 at 4:51 PM Jakob Erdmann <[email protected]> wrote: > > the second problem still remains and bus can not re-enter the road after > the traffic volume increases > You can change the junction type where the bus bay ends to "zipper" to > ensure that the bus can merge. > > > I see that emission outputs reported "zero" for some vehicles while they > were on their way. > https://github.com/eclipse/sumo/issues/2110 > > Am Sa., 30. Apr. 2022 um 22:38 Uhr schrieb ali mirzaei < > [email protected]>: > >> I could insert the bus into its bay as you said and the emission outputs >> were recorded continuously. But, the second problem still remains and bus >> can not re-enter the road after the traffic volume increases. On the other >> hand, in some time steps, I see that emission outputs reported "zero" for >> some vehicles while they were on their way. >> >> >> On Sat, Apr 30, 2022 at 4:10 PM Jakob Erdmann <[email protected]> >> wrote: >> >>> startPos and pos must be in the range [0, 12] to stop on that edge. The >>> values always count from the start of the stop edge. >>> >>> Am Sa., 30. Apr. 2022 um 00:45 Uhr schrieb ali mirzaei < >>> [email protected]>: >>> >>>> I think I did so, didn't I? >>>> My startPos = 112.19 and the pos = 124.49 >>>> >>>> On Sat, Apr 30, 2022 at 2:31 AM Jakob Erdmann <[email protected]> >>>> wrote: >>>> >>>>> the lane for the bus bay is only 12m long. You'll have to set your >>>>> stop position within that range. >>>>> >>>>> Am Fr., 29. Apr. 2022 um 22:34 Uhr schrieb ali mirzaei < >>>>> [email protected]>: >>>>> >>>>>> I did what you said in my opinion but at the beginning of the >>>>>> simulation I faced the error : stop for vehicle 'bus_1' on lane 'e2_0' >>>>>> has >>>>>> an invalid position. Could you tell me what mistakes I have made? (I have >>>>>> attached my files for possible information required) >>>>>> >>>>>> >>>>>> On Fri, Apr 29, 2022 at 3:16 PM Jakob Erdmann <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> The extra lane should only be as long as the bus bay and you'd >>>>>>> typically need to split the original edge into 3 parts to achieve this. >>>>>>> >>>>>>> Am Fr., 29. Apr. 2022 um 12:37 Uhr schrieb ali mirzaei < >>>>>>> [email protected]>: >>>>>>> >>>>>>>> I added an extra lane and used it as a bus stop at the specified >>>>>>>> coordinates but before getting there, the bus makes a lane change from >>>>>>>> the >>>>>>>> upstream (which is not desired) and after the end of the stop period, >>>>>>>> it >>>>>>>> moves in the extra lane and no longer backs to its primary lane (which >>>>>>>> is >>>>>>>> not desired, too). >>>>>>>> >>>>>>>> On Fri, Apr 29, 2022 at 10:32 AM Jakob Erdmann < >>>>>>>> [email protected]> wrote: >>>>>>>> >>>>>>>>> 1. if a vehicle stops with attribute parking="true", it no longer >>>>>>>>> records emissions (up to the time where the stop ends and it tries to >>>>>>>>> re-enter the network) >>>>>>>>> 2. if a vehicle returns from the "parking" state, road traffic >>>>>>>>> will generally not be are of it's wish to re-enter the road and thus >>>>>>>>> not >>>>>>>>> open a gap >>>>>>>>> >>>>>>>>> Both issues can be solved by modelling each bus bay with an extra >>>>>>>>> lane and having the bus stay on that lane during it's stop. >>>>>>>>> >>>>>>>>> Am Fr., 29. Apr. 2022 um 00:15 Uhr schrieb ali mirzaei < >>>>>>>>> [email protected]>: >>>>>>>>> >>>>>>>>>> Hi everyone, >>>>>>>>>> Using the ~.setStop() method, my buses start performing station >>>>>>>>>> operations where they were previously assigned. The emission class is >>>>>>>>>> "HBEFA3/PC_G_EU4". >>>>>>>>>> 1 - After observing some irregularities in the emission curves, I >>>>>>>>>> evaluated the emission outputs and found that at the moment the >>>>>>>>>> vehicle >>>>>>>>>> arrived at the station, the whole emission attributes turned to zero >>>>>>>>>> and >>>>>>>>>> after that no data of the vehicle was recorded for the duration >>>>>>>>>> length. >>>>>>>>>> This process stops when the vehicle leaves the station and the >>>>>>>>>> pollution >>>>>>>>>> information is recorded again. Why does this happen? >>>>>>>>>> 2 - When I add more vehicles to the road to simulate the rush >>>>>>>>>> hour effect on the operation, the merging of the bus would not >>>>>>>>>> happen in >>>>>>>>>> the determined period. How can I fix it? >>>>>>>>>> Best regards, >>>>>>>>>> Ali >>>>>>>>>> >>>>>>>>>> _______________________________________________ >>>>>>>>>> sumo-user mailing list >>>>>>>>>> [email protected] >>>>>>>>>> To unsubscribe from this list, visit >>>>>>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>>>>>> >>>>>>>>> _______________________________________________ >>>>>>>>> sumo-user mailing list >>>>>>>>> [email protected] >>>>>>>>> To unsubscribe from this list, visit >>>>>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>>>>> >>>>>>>> _______________________________________________ >>>>>>>> sumo-user mailing list >>>>>>>> [email protected] >>>>>>>> To unsubscribe from this list, visit >>>>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>>>> >>>>>>> _______________________________________________ >>>>>>> sumo-user mailing list >>>>>>> [email protected] >>>>>>> To unsubscribe from this list, visit >>>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>>> >>>>>> _______________________________________________ >>>>>> sumo-user mailing list >>>>>> [email protected] >>>>>> To unsubscribe from this list, visit >>>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>>> >>>>> _______________________________________________ >>>>> sumo-user mailing list >>>>> [email protected] >>>>> To unsubscribe from this list, visit >>>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>>> >>>> _______________________________________________ >>>> sumo-user mailing list >>>> [email protected] >>>> To unsubscribe from this list, visit >>>> https://www.eclipse.org/mailman/listinfo/sumo-user >>>> >>> _______________________________________________ >>> sumo-user mailing list >>> [email protected] >>> To unsubscribe from this list, visit >>> https://www.eclipse.org/mailman/listinfo/sumo-user >>> >> _______________________________________________ >> sumo-user mailing list >> [email protected] >> To unsubscribe from this list, visit >> https://www.eclipse.org/mailman/listinfo/sumo-user >> > _______________________________________________ > sumo-user mailing list > [email protected] > To unsubscribe from this list, visit > https://www.eclipse.org/mailman/listinfo/sumo-user >
_______________________________________________ sumo-user mailing list [email protected] To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-user
