good evening,
I will try first of all to put order and to answer your questions:
the weather station is a froggit wh3080 with separate sensors at 433 mhz,
therefore the old model. Here is the photo in jpg
[image: Profi-radio-Stazione-Meteo-wh3080-luce-UV-USB.jpg]
IThis is the result of what the stick sees thanks to the rtl command:
sudo rtl_433 -R 32
time : 2022-08-16 17:20:15
model : Fineoffset-WHx080 Msg type : 0
Station ID: 226
Battery : 1 Temperature: 32.9 C Humidity : 36 %
Wind Direction: 0 Wind avg speed: 0.00 Wind gust : 0.00
Total rainfall: 65.1 Integrity : CRC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _
time : 2022-08-16 17:20:27
model : Fineoffset-WHx080 Msg type : 2
UV Sensor ID: 225 Sensor Status: OK UV Index : 4
Lux : 84102.8 Watts/m : 123.14 Integrity : CRC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _
time : 2022-08-16 17:20:27
model : Fineoffset-WHx080 Msg type : 2
UV Sensor ID: 225 Sensor Status: OK UV Index : 4
Lux : 84102.8 Watts/m : 123.14 Integrity : CRC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _
time : 2022-08-16 17:20:27
model : Fineoffset-WHx080 Msg type : 2
UV Sensor ID: 225 Sensor Status: OK UV Index : 4
Lux : 84102.8 Watts/m : 123.14 Integrity : CRC
the command lines inserted in the sdr:
driver = user.sdr
cmd = rtl_433 -R 32 -R 40 -R 42
the command lines inserted in the sensor map
UV = uv_index.225.FOWH3080Packet
radiation = radiation.225.FOWH3080Packet
also replaced by another entry
UV = uv_index.225.FOWHx080Packet
radiation = radiation.225.FOWHx3080Packet
finally this is the result of the driver weewx sdr using the command
PYTHONPATH=/home/weewx/bin python /home/weewx/bin/user/sdr.py --config
/home/weewx/weewx.conf --hide=parsed,mapped
out: ['{"time" : "2022-08-16 15:40:27", "model" : "Fineoffset-WHx080",
"subtype" : 2, "uv_sensor_id" : 225, "uv_status" : "OK", "uv_index" : 3,
"lux" : 66370.100, "wm" : 97.174, "mic" : "CRC"}\n', '{"time" : "2022-08-16
15:40:27", "model" : "Fineoffset-WHx080", "subtype" : 2, "uv_sensor_id" :
225, "uv_status" : "OK", "uv_index" : 3, "lux" : 66370.100, "wm" : 97.174,
"mic" : "CRC"}\n', '{"time" : "2022-08-16 15:40:27", "model" :
"Fineoffset-WHx080", "subtype" : 2, "uv_sensor_id" : 225, "uv_status" :
"OK", "uv_index" : 3, "lux" : 66370.100, "wm" : 97.174, "mic" : "CRC"}\n']
inside the syslog there is no trace of UV or radiation
> I currently don't have it in front of me and am just writing from my
> phone, but maybe i can give a few hints:
>
> Which sdr command do you use in your config file? Try adding:
>
> -Y classic
>
> Which WHx080 model do you have? Is it the old one with separated sensors
> or the newer all in one sensor array?
>
> Do the other sensors work with your sdr weewx conf?
>
> Please keep in mind, the whx080 never really gave accurate solar radiation
> readings in the first place, mine showed 600 instead of 900 w/m2 last
> month. The newer wh65 array does this a lot better imo (but worse for wind
> gusts instead..)
>
> You will have to add in stdCalibrate -> Corrections
>
> radiation = radiation/126.7
>
> To convert the lux illuminance to w/m2 radiation readings.
>
> There is a way to show the recorded loop packets in the terminal but i
> can't remember the command, if you find it, check and see if weewx is
> getting the data. If so, make sure the uv and radiation fields exist in
> your database, and whether or not they are listed in your skin.conf (for
> plots as well as the current values)
>
>
>
> [email protected] schrieb am Sonntag, 14. August 2022 um 14:14:29 UTC+2:
>
>> can anyone help me?
>>
>> Il giorno martedì 9 agosto 2022 alle 16:49:48 UTC+2 Peppe ha scritto:
>>
>>> sorry, the last line is wrong
>>> this is what I wanted to write
>>> radiation = radiation.225.FOWH3080Packet
>>>
>>> Il giorno mar 9 ago 2022 alle ore 16:46 Peppe <[email protected]> ha
>>> scritto:
>>>
>>>> good evening
>>>> I put the two lines on the sensor map but it doesn't work. I am writing
>>>> you a series of attempts made by me along with your suggestions:
>>>> UV = uv_index.225.FOWHx080Packet
>>>> radiation = light.225.FOWHx080Packet
>>>> radiation = radiation.225.FOWHx080Packet
>>>> UV = uv_index.225.FOWH3080Packet
>>>> radiation = light.225.FOWH3080Packet
>>>> radiation = light.225.FOWH3080Packet
>>>> I don't know what I did wrong.
>>>> I rewrite the data I receive from my Nesdr:
>>>> {"time": "2022-08-09 14:42:36", "model": "Fineoffset-WHx080",
>>>> "subtype": 2, "uv_sensor_id": 225, "uv_status": "OK", "uv_index ": 3," lux
>>>> ": 36888.800," wm ": 54.010," mic ":" CRC "}
>>>>
>>>> Il giorno lun 8 ago 2022 alle ore 16:44 Peppe <[email protected]> ha
>>>> scritto:
>>>>
>>>>>
>>>>> first of all thank you so much for answering me. I was wrong in
>>>>> transcribing the syslog.
>>>>> this is correct: {"time": "2022-08-07 13:26:39", "model":
>>>>> "Fineoffset-WHx080", "subtype": 2, "uv_sensor_id": 225, "uv_status": " OK
>>>>> "," uv_index ": 2," lux ": 32082.000," wm ": 46,972," mic ":" CRC "}
>>>>> I'll try your suggestions and post them here
>>>>>
>>>>> Il giorno lunedì 8 agosto 2022 alle 09:18:08 UTC+2 [email protected]
>>>>> ha scritto:
>>>>>
>>>>>> I've never seen "*End*offset-WHx080", not sure if this is available
>>>>>> in sdr.py, but maybe I'm wrong.
>>>>>>
>>>>>> Mine works with following sensor map entries:
>>>>>>
>>>>>> UV = uv_index.*.FOWHx080Packet
>>>>>> radiation = light.*.FOWHx080Packet
>>>>>>
>>>>>> You can replace *** with your ID (necessary if there are other
>>>>>> WHx080 stations around)
>>>>>>
>>>>>>
>>>>>> [email protected] schrieb am Sonntag, 7. August 2022 um 15:45:17
>>>>>> UTC+2:
>>>>>>
>>>>>>> I used a weeewx 4.8.0 installation using the weewx-sdr driver
>>>>>>> updated on February 12th of this year and capturing the sensors at 433
>>>>>>> mhz
>>>>>>> with a Nesdr key;
>>>>>>> the sdr.py file is from January 22nd
>>>>>>>
>>>>>>> Il giorno domenica 7 agosto 2022 alle 15:32:29 UTC+2 Peppe ha
>>>>>>> scritto:
>>>>>>>
>>>>>>>> Hello everyone, I ask you for a little help to insert the uv and
>>>>>>>> radiation sensors of a whx080 station into my sensor map.
>>>>>>>> Here is the result of the sudo rtl_433 -M utc -F json command:
>>>>>>>>
>>>>>>>> {"time": "2022-08-07 13:26:39", "model": "Endoffset-WHx080",
>>>>>>>> "subtype": 2, "uv_sensor_id": 225, "uv_status": "OK", "uv_index ": 2,"
>>>>>>>> lux
>>>>>>>> ": 32082.000," wm ": 46,972," mic ":" CRC "}
>>>>>>>>
>>>>>>>> What is the right line to insert within the weewx.conf sensor map?
>>>>>>>> thanks for your cooperation and sorry for my bad english
>>>>>>>>
>>>>>>> --
>>>>> You received this message because you are subscribed to a topic in the
>>>>> Google Groups "weewx-user" group.
>>>>> To unsubscribe from this topic, visit
>>>>> https://groups.google.com/d/topic/weewx-user/PohR3wcR1UM/unsubscribe.
>>>>> To unsubscribe from this group and all its topics, send an email to
>>>>> [email protected].
>>>>> To view this discussion on the web visit
>>>>> https://groups.google.com/d/msgid/weewx-user/e67461ea-3e02-4979-afd2-7191a4cfc043n%40googlegroups.com
>>>>> <https://groups.google.com/d/msgid/weewx-user/e67461ea-3e02-4979-afd2-7191a4cfc043n%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>> .
>>>>>
>>>> --
> You received this message because you are subscribed to a topic in the
> Google Groups "weewx-user" group.
> To unsubscribe from this topic, visit
> https://groups.google.com/d/topic/weewx-user/PohR3wcR1UM/unsubscribe.
> To unsubscribe from this group and all its topics, send an email to
> [email protected].
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/weewx-user/11d088ca-4d0d-4979-9558-9dbdab25bf7dn%40googlegroups.com
> <https://groups.google.com/d/msgid/weewx-user/11d088ca-4d0d-4979-9558-9dbdab25bf7dn%40googlegroups.com?utm_medium=email&utm_source=footer>
> .
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/CAOvMtO8oPRD-YqdT5yNt573HS1jq2SujRQuxXoDgp0F5QodfGQ%40mail.gmail.com.
