disable the wep and make the ssid's the same!! you shouldn't use the diversity antennas but if you specify your antenna, make sure you specify the right one.
----- Original Message ----- From: "Julián Llantén Trujillo" <[EMAIL PROTECTED]> To: "George" <[EMAIL PROTECTED]> Cc: "802.11B NEWS GROUP" <[EMAIL PROTECTED]>; "Jason Straight" <[EMAIL PROTECTED]>; "Brian Taylor" <[EMAIL PROTECTED]> Sent: Monday, July 28, 2003 1:18 AM Subject: Re: [BAWUG] LINKSYS WAP11B V2.6 > > My settings are: > > Basic rate: 1, 2, 5.5, 11 > Transfer rate: 1, 2, 5.5, 11 > Mode: point-to-point and point-to-multipoint bridge > SSID: Different in both of them > Wep: 128 bits > Diversity antenna in both of them. > Beacon interval: 70 > > I was told that it would be better not to use diversity antenna as the wap > would divide it's power in both of them. I use a 12 dbi omni in one side > and a 16 dbi VAGI in the other together with their own 2.2 rubber duck > antennas. > > Finally: after your wap stopped working did yout test them again while > each one next to other ? this would ensure they're not damaged and that > maybe your noise conditions has increased. > > > On Mon, 28 Jul 2003, George wrote: > > > > > > > > > ----- Original Message ----- > > From: "Julián Llantén Trujillo" <[EMAIL PROTECTED]> > > To: "George" <[EMAIL PROTECTED]> > > Cc: "802.11B NEWS GROUP" <[EMAIL PROTECTED]>; "Jason Straight" > > <[EMAIL PROTECTED]>; "Brian Taylor" <[EMAIL PROTECTED]> > > Sent: Sunday, July 27, 2003 10:30 PM > > Subject: Re: [BAWUG] LINKSYS WAP11B V2.6 > > > > > > > > > > Seems like an antenna problem or a wap11 problem. I have a 1km link with > > > wap11 2.6 too and they have been working fine. Have you tried to link them > > > while being together ? > > > > > > Can you tell me your settings on your 2.6 Julian. what I only changed to > > make a link is the BASIC RATE i set it to 1-2 Mbps > > and the TRANSMIT RATE at 1-2-5.5-11Mbps factory setting. All others by > > default. > > > > Yeah I did try them before straight right out of the box. Using Wireless > > Bridge Point to Point and Point to Multi Point. > > And they are working on channel 6. But havent trued to change the > > channel. But as the guys said. It doesnt matter. > > > > >just in case, they may just got damaged (for any > > > reason). > > > > > > Bridging does work fine on them. Both point-to-point and > > > point-to-multipoint works. They say they will work only with other wap11. > > > > Are you saying that BOTH v2.6 configured as Wireless Bridge POint to > > Point...it must work. And or BOTH on Point to Multi POint it should run > > also. > > > > Bec. Previousely I made it to run at 1.5mile with one set to AP mode and > > the other at AP Client mode. Then I got a link. > > my firmware is factory. 1.06 > > > > I have attached a screen shot of my 2.6 here for your refrence. > > > > > Btw, have your tried linking a wap11 with another brand name ? > > > > > > > NO, I havent tried it. But I have a pair of 2.2's that are working > > with no problem but short distance around 2 block away. Set at PXP and > > PXMP . Sometimes they hang bec of heat but tolerable. > > > > > > > > > -- > general wireless list, a bawug thing <http://www.bawug.org/> > [un]subscribe: http://lists.bawug.org/mailman/listinfo/wireless -- general wireless list, a bawug thing <http://www.bawug.org/> [un]subscribe: http://lists.bawug.org/mailman/listinfo/wireless
