Thanks Steve Sanity regained!!! On Tue, 27 Nov 2018 at 10:43, Stephen Ireland <vk3...@hotmail.com> wrote:
> Ken (and others), > > > > I am actually sending now (27/11/18 UTC 00:30) main band 20m at 1550 Hz. > > Everyone so no screaming about operating above 2K in offset as I am > interested in the interaction between v1 and v2 sigs. > > > > I have been doing so for around 5 mins on a rather active band ... I will > do so for around another hour or so. > > > > 73 > > > > Steve I > > > > Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for > Windows 10 > > > ------------------------------ > *From:* Ken Myers <kenmyersglo...@gmail.com> > *Sent:* Tuesday, November 27, 2018 11:31:14 AM > *To:* wsjt-devel@lists.sourceforge.net > *Subject:* Re: [wsjt-devel] 2RSC3 > 2RSC4 decoding disappeared FT8 > > 1 decode on 20m - frq 383 ?? seems to work. Like fishing - have to wait > quietly or NOISILY sent out string of CQ - no fish. Checking 6m > > THanks > > > On Tue, 27 Nov 2018 at 09:53, Ken Myers <kenmyersglo...@gmail.com> wrote: > >> Thanks - shall persist >> >> Cheers Ken >> VK4GC >> >> On Tue, 27 Nov 2018 at 09:42, Bill Somerville <g4...@classdesign.com> >> wrote: >> >>> Hi Ken, >>> >>> comments in line below. >>> >>> On 26/11/2018 23:15, Ken Myers wrote: >>> > 2 installations - >>> > 1 MSSurface Win10 up to date, 2 radios (FT991a & FTdx3000 both USB) - >>> > non decode, >>> > 2 HP Allinone with FT897/Singnalink. - non decode, >>> > (both setups using HRD (up to date) for CAT control) >>> This combination of rig and interface requires a specific setup. The >>> FT-817/857/897(D) series of rigs do not accept CAT commands while >>> transmitting. You must *not* check the settings option >>> "Settings->General->Allow Tx frequency changes while transmitting" and >>> you must set the SignaLink delay knob to minimum. You should set the >>> WSJT-X PTT configuration "Settings->Radio->PTT Method" to "VOX" although >>> some have found it necessary to use the CAT PTT Method to avoid any CAT >>> commands while the rig is in Tx mode. >>> > >>> > For all: >>> > 1.9.1 works great >>> > 2.0 RC3 works great >>> > 2.0 RC4 good waterfall (therefore good audio present) - NO decode. >>> > >>> > uninstalling/reinstalling forward and back through versions gives the >>> > same result. >>> > >>> > i have concluded: >>> > 1 I must be holding my mouth wrong - OR >>> > 2 I have missed a new setting. >>> > 3 When I have been looking/testing RC4, no RC4 (77 bit) >>> > transmissions. Not sure here as I have been especially been looking >>> > top band. >>> > >>> > 2 probably!! >>> > >>> Almost certainly 3, there has been a relatively low usage to 77-bit FT8 >>> on the normal HF FT8 sub-bands. It seems that most users of RC4 have >>> reverted to v1.9.1 so the volume of 77-bit traffic is low except for a >>> couple of days after a beta release. It would be good if users of RC5 >>> could stick with it and try to drive up the level of activity so that >>> issues can be discovered before the final GA release. >>> >>> 73 >>> Bill >>> G4WJS. >>> >>> >>> >>> _______________________________________________ >>> wsjt-devel mailing list >>> wsjt-devel@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> >> >> >> -- >> Cheers >> >> Ken Myers >> >> Sunnybank Hills QLD AUS >> M +61 414 487 004 >> >> > > -- > Cheers > > Ken Myers > > Sunnybank Hills QLD AUS > M +61 414 487 004 > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > -- Cheers Ken Myers Sunnybank Hills QLD AUS M +61 414 487 004
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
