Hi,

    Thanks for the quick response. I just tried HandShake = NONE and I
have the same result - Rig Failure - HamLib Error.

   Any other suggestions?

Thanks!

Bill - AK6A

On Sat, May 23, 2020 at 3:32 PM Bill Somerville <g4...@classdesign.com>
wrote:

> On 23/05/2020 23:16, Bill wrote:
>
> I am having an issue connecting a Yaesu FTDX-101MP to WSJT-X on a Mac. I’m
> able to get the receive Audio Codec to work properly and I can see decodes
> but I get a “Rig Failure - Hamlib Error - Invalid configuration while
> opening connection to rig” whenever I do a Test CAT. I am unable to get
> WSJT-X to establish control communications with the radio. I’ve seen online
> suggestions that say use the HamLib FT-991 selection. I am using the
> regular WSJT-X version 2.1.2. I am also just using a USB cable from the
> radio to the Mac which is running High Sierra. I am using the following
> settings:
>
>
> WSJT-X
>
>
> RADIO TAB
>
>
> Rig: Yaesu FT-991
>
>
> Serial Port: /dev/cu.SLAB_USBtoUART1
>
> Note: Installed latest Silicon Labs Drivers - Also Available selections:
>
> /dev/tty.SLAB_USBtoUART1
>
> /dev/cu.SLAB_USBtoUART
>
> /dev/tty.SLAB_USBtoUART
>
>
> Baud Rate: 38400
>
> Polling Interval: 1S
>
> Data Bits: Eight
>
> Stop Bits: Two
>
> Handshake: Hardware
>
> Force Control Lines: Both Empty
>
>
> PTT Method: CAT
>
> Mode: None
>
> Split: Rig
>
>
> AUDIO Tab
>
>
> Input - USB AUDIO CODEC
> Output - USB AUDIO CODEC
>
> FTDX101MP Menu
>
>
> FUNC --> Operation Settings
> General
> 232C RATE - 38400
> CAT RATE - 38400
>
> FUNC --> RADIO SETTINGS
> MODE SSB
> SSB MOD SOURCE - REAR
> REAR SELECT - USB
> RPORT GAIN - 10
> DATA MODE SOURCE - REAR (This is the default)
> REAR SELECT - USB
> DATA OUT LEVEL - 10
> RPORT GAIN - 10
>
> RADIO MAIN PANEL & DISPLAY
>
>
>
> R.FIL - 3kHz
> WIDTH - 4000Hz
>
>
> APPLE COMPUTER
>
>
> USB AUDIO CODEC 1 Format: 2 ch 16-bit Integer 48 kHz
> USB AUDIO CODEC 2 Format: 2 ch 16-bit Integer 48 kHz
>
>
>
>
> Any ideas what might be the issue in getting this going? Has anyone else
> been able to get a FTDX-101MP working with WSJT-X? Do I need to install a
> newer version of HamLib for this new radio?
>
>
> Thanks!
>
>
> Bill - AK6A
>
> Hi Bill,
>
> try with "Settings->Radio->Handshake->None".
>
> 73
> Bill
> G4WJS.
> _______________________________________________
> wsjt-devel mailing list
> wsjt-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
>
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Reply via email to