My suspicion is that your IMM2 is set to use the dedicated IMM ethernet port, but you intended to use the shared IMM/eth0 port instead.
This needs to be configured using the UEFI -- hit <F1> configuration, under the tab where other IMM network settings are found. If there is a way to do this using ipmitool, I have not found it. If you plug a separate cable between switch and dedicated IMM port, and the MAC you're looking for shows up on that switch port when you ping it, you can then use ASU to change IMM.SharedNicMode from Dedicated to Shared and then reboot the imm (ipmitool mc reset cold). [note -- I checked this on an x3550-M4, sometimes the variables are spelled differently from release to release]. Remove the extra cable, and you should be back in business. -- ddj Dave Johnson Brown University CCV On Oct 6, 2015, at 10:56 AM, Damir Krstic <[email protected]> wrote: > We have new x3550M5 that we just discovered. After being discovered I ran > runcmd=bmcsetup command. I can ssh to the node and ipmitool lan print 1 tells > me the following: > [xCAT Genesis running on qhimem0004 /]# ipmitool lan print 1 > > Set in Progress : Set Complete > > Auth Type Support : NONE MD5 PASSWORD > > Auth Type Enable : Callback : > > : User : MD5 PASSWORD > > : Operator : MD5 PASSWORD > > : Admin : MD5 > > : OEM : > > IP Address Source : Static Address > > IP Address : 172.29.10.14 > > Subnet Mask : 255.255.0.0 > > MAC Address : 40:f2:e9:bb:86:dd > > SNMP Community String : public > > IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 > > BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Disabled > > Gratituous ARP Intrvl : 2.0 seconds > > Default Gateway IP : 0.0.0.0 > > Default Gateway MAC : 00:00:00:00:00:00 > > Backup Gateway IP : 0.0.0.0 > > Backup Gateway MAC : 00:00:00:00:00:00 > > 802.1q VLAN ID : Disabled > > 802.1q VLAN Priority : 0 > > RMCP+ Cipher Suites : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16 > > Cipher Suite Priv Max : Xaaaaaaaaaaaaaa > > : X=Cipher Suite Unused > > : c=CALLBACK > > : u=USER > > : o=OPERATOR > > : a=ADMIN > > : O=OEM > > > > The IP is correct, and for set it indicates complete. However, I can not > telnet to this IP (qhimem0004-bmc). > > Here is the hosts table entry for this node: > > > "qhimem0004-bmc","172.29.10.14",,,"qhimem0014 node bmc interface", > > Here is the /etc/hosts file entry: > > > 172.29.10.14 qhimem0004-bmc.quest.it.northwestern.edu qhimem0004-bmc > > here is the nodels entry for the ipmi port: > > [root@mgt log]# nodels qhimem0004 ipmi.bmcport > > > qhimem0004: 0 > > When trying to telnet to this address I get no route to host. I have logged > in to the switch itself and see mac address of the interface show up on the > port on the switch, but not the mac of the BMC port. > > > > Any help is greatly appreciated. > > Thanks, > > Damir > > ------------------------------------------------------------------------------ > _______________________________________________ > xCAT-user mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/xcat-user
------------------------------------------------------------------------------
_______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user
