If I remember correctly, changing the IP address does not take effect until the IMM/BMC is reset, or power-cycled.
On Oct 6, 2015, at 1:03 PM, Damir Krstic <[email protected]> wrote: > I am not sure that's the case with these nodes. I have provisioned few > x3550M5s over few days and none of them had this issue. The issue with this > node is that I mis-provisioned it (using wrong IP etc.) so this morning I > cleared everything out and tried again. I see via ipmitool that set is > complete, but the destiny of the node never changes from bmcsetup. > > Is there way to force it to reprogram again? > > Damir > > On Tue, Oct 6, 2015 at 10:59 AM David D Johnson <[email protected]> > wrote: > My suspicion is that your IMM2 is set to use the dedicated IMM ethernet port, > but you intended to use the shared IMM/eth0 port instead. > > This needs to be configured using the UEFI -- hit <F1> configuration, under > the tab > where other IMM network settings are found. If there is a way to do this > using ipmitool, > I have not found it. > > If you plug a separate cable between switch and dedicated IMM port, and the > MAC > you're looking for shows up on that switch port when you ping it, you can > then use ASU to change > IMM.SharedNicMode from Dedicated to Shared and then reboot the imm (ipmitool > mc reset cold). > [note -- I checked this on an x3550-M4, sometimes the variables are spelled > differently from release to release]. > > Remove the extra cable, and you should be back in business. > > -- ddj > Dave Johnson > Brown University CCV > > On Oct 6, 2015, at 10:56 AM, Damir Krstic <[email protected]> wrote: > >> We have new x3550M5 that we just discovered. After being discovered I ran >> runcmd=bmcsetup command. I can ssh to the node and ipmitool lan print 1 >> tells me the following: >> [xCAT Genesis running on qhimem0004 /]# ipmitool lan print 1 >> >> Set in Progress : Set Complete >> >> Auth Type Support : NONE MD5 PASSWORD >> >> Auth Type Enable : Callback : >> >> : User : MD5 PASSWORD >> >> : Operator : MD5 PASSWORD >> >> : Admin : MD5 >> >> : OEM : >> >> IP Address Source : Static Address >> >> IP Address : 172.29.10.14 >> >> Subnet Mask : 255.255.0.0 >> >> MAC Address : 40:f2:e9:bb:86:dd >> >> SNMP Community String : public >> >> IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 >> >> BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Disabled >> >> Gratituous ARP Intrvl : 2.0 seconds >> >> Default Gateway IP : 0.0.0.0 >> >> Default Gateway MAC : 00:00:00:00:00:00 >> >> Backup Gateway IP : 0.0.0.0 >> >> Backup Gateway MAC : 00:00:00:00:00:00 >> >> 802.1q VLAN ID : Disabled >> >> 802.1q VLAN Priority : 0 >> >> RMCP+ Cipher Suites : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16 >> >> Cipher Suite Priv Max : Xaaaaaaaaaaaaaa >> >> : X=Cipher Suite Unused >> >> : c=CALLBACK >> >> : u=USER >> >> : o=OPERATOR >> >> : a=ADMIN >> >> : O=OEM >> >> >> >> The IP is correct, and for set it indicates complete. However, I can not >> telnet to this IP (qhimem0004-bmc). >> >> Here is the hosts table entry for this node: >> >> >> "qhimem0004-bmc","172.29.10.14",,,"qhimem0014 node bmc interface", >> >> Here is the /etc/hosts file entry: >> >> >> 172.29.10.14 qhimem0004-bmc.quest.it.northwestern.edu qhimem0004-bmc >> >> here is the nodels entry for the ipmi port: >> >> [root@mgt log]# nodels qhimem0004 ipmi.bmcport >> >> >> qhimem0004: 0 >> >> When trying to telnet to this address I get no route to host. I have logged >> in to the switch itself and see mac address of the interface show up on the >> port on the switch, but not the mac of the BMC port. >> >> >> >> Any help is greatly appreciated. >> >> Thanks, >> >> Damir >> > >> ------------------------------------------------------------------------------ >> _______________________________________________ >> xCAT-user mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/xcat-user > > ------------------------------------------------------------------------------ > _______________________________________________ > xCAT-user mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/xcat-user > ------------------------------------------------------------------------------ > _______________________________________________ > xCAT-user mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/xcat-user
------------------------------------------------------------------------------
_______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user
