No, it's immediate. From: David D Johnson [mailto:[email protected]] Sent: Tuesday, October 06, 2015 1:17 PM To: xCAT Users Mailing list Subject: Re: [xcat-user] issue programing bmc
If I remember correctly, changing the IP address does not take effect until the IMM/BMC is reset, or power-cycled. On Oct 6, 2015, at 1:03 PM, Damir Krstic <[email protected]<mailto:[email protected]>> wrote: I am not sure that's the case with these nodes. I have provisioned few x3550M5s over few days and none of them had this issue. The issue with this node is that I mis-provisioned it (using wrong IP etc.) so this morning I cleared everything out and tried again. I see via ipmitool that set is complete, but the destiny of the node never changes from bmcsetup. Is there way to force it to reprogram again? Damir On Tue, Oct 6, 2015 at 10:59 AM David D Johnson <[email protected]<mailto:[email protected]>> wrote: My suspicion is that your IMM2 is set to use the dedicated IMM ethernet port, but you intended to use the shared IMM/eth0 port instead. This needs to be configured using the UEFI -- hit <F1> configuration, under the tab where other IMM network settings are found. If there is a way to do this using ipmitool, I have not found it. If you plug a separate cable between switch and dedicated IMM port, and the MAC you're looking for shows up on that switch port when you ping it, you can then use ASU to change IMM.SharedNicMode from Dedicated to Shared and then reboot the imm (ipmitool mc reset cold). [note -- I checked this on an x3550-M4, sometimes the variables are spelled differently from release to release]. Remove the extra cable, and you should be back in business. -- ddj Dave Johnson Brown University CCV On Oct 6, 2015, at 10:56 AM, Damir Krstic <[email protected]<mailto:[email protected]>> wrote: We have new x3550M5 that we just discovered. After being discovered I ran runcmd=bmcsetup command. I can ssh to the node and ipmitool lan print 1 tells me the following: [xCAT Genesis running on qhimem0004 /]# ipmitool lan print 1 Set in Progress : Set Complete Auth Type Support : NONE MD5 PASSWORD Auth Type Enable : Callback : : User : MD5 PASSWORD : Operator : MD5 PASSWORD : Admin : MD5 : OEM : IP Address Source : Static Address IP Address : 172.29.10.14 Subnet Mask : 255.255.0.0 MAC Address : 40:f2:e9:bb:86:dd SNMP Community String : public IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Disabled Gratituous ARP Intrvl : 2.0 seconds Default Gateway IP : 0.0.0.0 Default Gateway MAC : 00:00:00:00:00:00 Backup Gateway IP : 0.0.0.0 Backup Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16 Cipher Suite Priv Max : Xaaaaaaaaaaaaaa : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM The IP is correct, and for set it indicates complete. However, I can not telnet to this IP (qhimem0004-bmc). Here is the hosts table entry for this node: "qhimem0004-bmc","172.29.10.14",,,"qhimem0014 node bmc interface", Here is the /etc/hosts file entry: 172.29.10.14 qhimem0004-bmc.quest.it.northwestern.edu<http://qhimem0004-bmc.quest.it.northwestern.edu/> qhimem0004-bmc here is the nodels entry for the ipmi port: [root@mgt log]# nodels qhimem0004 ipmi.bmcport qhimem0004: 0 When trying to telnet to this address I get no route to host. I have logged in to the switch itself and see mac address of the interface show up on the port on the switch, but not the mac of the BMC port. Any help is greatly appreciated. Thanks, Damir ------------------------------------------------------------------------------ _______________________________________________ xCAT-user mailing list [email protected]<mailto:[email protected]> https://lists.sourceforge.net/lists/listinfo/xcat-user ------------------------------------------------------------------------------ _______________________________________________ xCAT-user mailing list [email protected]<mailto:[email protected]> https://lists.sourceforge.net/lists/listinfo/xcat-user ------------------------------------------------------------------------------ _______________________________________________ xCAT-user mailing list [email protected]<mailto:[email protected]> https://lists.sourceforge.net/lists/listinfo/xcat-user
------------------------------------------------------------------------------
_______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user
