Ali, I see. So, you just need to go http://community.elphel.com/bootblock393/ again and put the correct data to make 5MPx work. See the attached image. In short - in the AUX Board table - make sure, *Application* field is *MT9P006 *, and the *Application mode* is *15 *. Then hit "PROGRAM AUX" - it's slow, so wait a bit (10 sec?). Then "READ AUX" to check the changes were made.
Then reboot the camera. And it should work. If not, please send the autocampars log again. I want to back up the micro-SD card but it dose not mount on any OS; how to > can I do it? It will mount in any Linux OS. Simply copying the files will not work - you need raw cloning - please, read about "dd"-utility. If you have Windows only then it should see the BOOT partition - it's FAT. Regards, Oleg On Tue, Oct 20, 2020 at 6:04 AM ali tamimi <tamimial...@gmail.com> wrote: > > Oleg, > Everything is OK with "14 Mpix" sensor; but when I connect the "5 Mpix" > no picture is seen at all. I'm sure that there is no problem with cable(it > works well with "14 Mpix" sensor ). The micro-SD card marked "5MPx" is also > insert to the slot too. I put the log files below. > And another question. I want to back up the micro-SD card but it dose not > mount on any OS; how to can I do it? > > *log files:* > *The "Read AUX" output:* > <board> > <brand>Elphel</brand> > <model>10389</model> > <rev>B</rev> > <serial>F80008</serial> > <time>1603185256</time> > <app>Eyesis4pi393</app> > <mode>1001</mode> > </board> > > *The "autocampars.log" :* > root@elphel393:~# cat /var/log/autocampars.log > 00014.09 autocampars: initializing state file /var/volatile/state/camera > 00014.27 autocampars: Application - Eyesis4pi393, mode: 1001 > > 00014.30 autocampars: Processing camera state: BOOT > 00014.33 autocampars: Got sensor map from sysfs: > 0: mt9p006, none, none, none > 1: mt9p006, none, none, none > 2: mt9p006, none, none, none > 3: mt9p006, none, none, none > 00014.35 autocampars: Active sensor ports: 0,1,2,3 master_port = 0 > 00014.38 autocampars: Sensors map read from the sysfs: [mt9p006, none, > none, none],[mt9p006, none, none, none],[mt9p006, none, none, > none],[mt9p006, none, none, none] > 00014.41 autocampars: Parsed existing ini file > 00014.43 autocampars: get_application_mode()->1013623 > 00014.46 autocampars: Parsed existing ini file > 00014.49 autocampars: Detecting sensors for Eyesis4pi393 > 00014.51 autocampars: Got --init command, initialization was not > completed, just continue > 00014.54 autocampars: detect_camera() > 00014.56 autocampars: detect_camera(): > 0: mt9p006, none, none, none > 1: mt9p006, none, none, none > 2: mt9p006, none, none, none > 3: mt9p006, none, none, none > 00014.59 autocampars: ports:0, 1, 2, 3 > 00014.62 autocampars: boot > 00014.64 autocampars: Parsed existing ini file > 00014.67 autocampars: Using sensor mask 0xf7777 > 00016.95 autocampars: Setting sensors/multiplexers power > 00016.98 autocampars: set_eyesis_power_control()=>Array > ( > [result] => OK > [retval] => 0 > ) > > 00017.00 autocampars: GLOBALS['camera_state_arr']=>Array > ( > [exit_stage] => > [state] => BOOT > [rev10389] => B > [application] => Eyesis4pi393 > [mode] => 1001 > [max_frame_time] => 300000 > [is_slave] => 1 > [eyesis_top] => 1 > [is_eyesis] => 1 > [eyesis_power] => 1 > [max_latency] => 5 > ) > > 00017.03 autocampars: Current state: BOOT > 00017.06 autocampars: This is a slave camera - waiting for master to > contol next steps > 00017.08 autocampars: Log file saved as /var/log/autocampars.log > 00017.11 autocampars: ---------------------------------------------- > root@elphel393:~# > > On Mon, Oct 19, 2020 at 10:18 PM Oleg <support-list@support.elphel.com> > wrote: > >> Ali, >> >> 1. Please send the /var/log/autocampars.log. It can help to rule out a >> possible misconfiguration. If everything is correct then one can assume >> it's a bad cable. >> >> 2. (just want to double check your configuration) Go >> http://community.elphel.com/bootblock393/, make sure the ip address in >> the 1st table is correct, then click "Read AUX" in the "AUX board >> (10389)"-table - what's the output? >> >> Regards, >> Oleg >> >> On Mon, Oct 19, 2020 at 9:21 AM Elphel Support < >> support-list@support.elphel.com> wrote: >> >>> Hello Ali, >>> >>> There should be no problems with impedance matching, we tested both >>> types of sensors with up to 450mm cables (for ectremely long cable >>> programmatic phase adjustment may be needed). And the cables are the same >>> for both serial (14MPix) and parallel (5MPix). >>> >>> Andrey >>> >>> >>> ---- On Mon, 19 Oct 2020 05:33:14 -0600 *ali tamimi >>> <tamimial...@gmail.com <tamimial...@gmail.com>>* wrote ---- >>> >>> Hello Oleg >>> yes, i can 'ssh' to camera and also can send >>> the/var/log/autocampars.log. The microSD card marked "5MPx" is also insert >>> to the slot. >>> We opened the camera. When closing the sensor cable was pressed slightly >>> and deformed. I guess the cable is damaged. In the parts list of the "5 >>> MPx" sensor, FFC cable with model number 050-30-51B, is provided. But >>> by connecting this cable, the sensor is not detected eaither.The >>> connection photo is sent in the attachment. Could there be a problem >>> with the cable (for example, impedance matching, etc.)? >>> >>> On Sun, Oct 18, 2020 at 11:23 AM Oleg <support-list@support.elphel.com> >>> wrote: >>> >>> Hello Ali, >>> >>> Can you 'ssh' to the camera? Could you send the /var/log/autocampars.log? >>> >>> ~$ ssh root@192.168.0.9 <http://mailto:root@192.168.0.9> >>> ~# cat /var/log/autocampars.log >>> >>> >>> Or if you use minicom - send the boot log. >>> >>> If I remember right you should have a microSD card marked a "5MPx" - the >>> camera autoboots from the card - I suggest you try the card first. And the >>> only thing you will need is to set "MT9*P*006" from the bootblock393 >>> page. >>> >>> Regards, >>> Oleg >>> >>> On Sun, Oct 18, 2020 at 7:56 AM ali tamimi <tamimial...@gmail.com> >>> wrote: >>> >>> Hello >>> We have provided your product 10393. Your camera is very well designed >>> and made. Thank you for your good products and complete documentation >>> and your support. >>> Sensor installed on 10393 is a 14-megapixel sensor (10398) "mt9f002" by >>> default that Works well. We also bought the 10338 "mt9006" sensor. By >>> replacing the sensors, the new one is not detectable and no image is >>> seen. >>> We downloaded the latest firmware, although the default sensor is >>> "mt9006" in the manual, the "devicetree.dtb" replacement process was >>> performed according to the instructions,10393 nand flash was programmed >>> but the sensor is not detected again.The image of error in web >>> interface sent in the attachment. Thanks for your support in solving >>> the problem. >>> _______________________________________________ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> >>> >>> _______________________________________________ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> >>> >>> >>> _______________________________________________ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> >> >> >> -- >> Best regards, >> Oleg Dzhimiev >> Electronics Engineer >> phone: +1 801 783 5555 x124 >> Elphel, Inc. >> > _______________________________________________ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > -- Best regards, Oleg Dzhimiev Electronics Engineer phone: +1 801 783 5555 x124 Elphel, Inc.
_______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
