Yes definitely need a SyncPipe Basic. I have made the mistake of not pushing the power terminal block all the way down on the SyncInjector, you might want to check that, like George says it will draw power from the bus but not power the APs.
From: Josh Luthman via Af Sent: Friday, November 28, 2014 8:34 PM To: [email protected] Subject: Re: [AFMUG] ePMP and/or Gig SyncInjector problems OK, I'll have to triple check the power on that sync injector. Also need a sync pipe. Anyone have a spare near Dayton Ohio? Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Nov 28, 2014 9:31 PM, "George Skorup (Cyber Broadcasting) via Af" <[email protected]> wrote: From the Base unit's expansion bus. The SyncInjectors will provide their own power to their exp. bus if the input block has (usable) voltage, otherwise it will pull power from the Base. Expansion bus only, NOT power for the radios, that's completely separate. On 11/28/2014 8:22 PM, Josh Luthman via Af wrote: Well how would the light turn on if it didn't have power? Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Nov 28, 2014 at 9:17 PM, George Skorup (Cyber Broadcasting) via Af <[email protected]> wrote: Six flashes, I'm trying to remember. I thought that means no power on the input block. Could mean no sync. But I'm thinking power, which would explain why your APs on that second injector won't come up at all. Yes, you definitely need a SyncPipe connected to one of the SyncInjectors. The sync daisy chain just means you can propagate the sync pulse from a "master" SyncInjector to a number of other ones. On 11/28/2014 8:07 PM, Josh Luthman via Af wrote: Oh forgot to mention power - everything is 24vdc from the same circuit (fuses are tested good from multimeter, 24v at every terminal). Note two of the APs are working on one gig sync injector where the other sync injector has 0 working APs. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Nov 28, 2014 at 9:05 PM, Josh Luthman <[email protected]> wrote: SiteMonitor isn't showing any of the three expansion parts (poe injector and 2x gig syncinjectors). Is a SyncPipe Basic required for the syncinjectors to work? Or do they have an GPS radio? I'm not seeing any documentation saying it's necessary, but it's mentioning it a lot... Will the gig syncinjectors still utilize 10 or 100 mbit? Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Nov 28, 2014 at 9:01 PM, Nate Burke via Af <[email protected]> wrote: Does your site monitor show anything out of the ordinary? What are you using to provide sync to the sync injector? The green lights on both should blink once per second when they have sync. On 11/28/2014 7:46 PM, Josh Luthman via Af wrote: Here's a video, not sure what the blinking means? https://www.youtube.com/watch?v=dME8A-H_590 Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Nov 28, 2014 at 8:39 PM, Josh Luthman via Af <[email protected]> wrote: *rb2011 with ports 2/3/4/5 set to hardware switch (ether2 master, 3/4/5 slave). Ports 6/7/8/9 are hardware switch (ether6 master, 7/8/9 slave). *From the rb2011 it goes to the Ethernet half of the SyncInjector. *From the POE half of the SyncInjector it goes to WB gigeapc HV surge suppressors and then to the ePMP radios. Two of the ePMP radios are powered up and running gige. Neither are receiving CMM sync (top of the ePMP says "Not receiving GPS sync"). The remaining 6 APs aren't even powering up/linking up. Any ideas before I start swapping parts? Is it OK to have the surge between SyncInjectors and ePMP? On top of all of this the SiteMonitor isn't talking to the POE injector or the two Gig SyncInjectors. I have them all daisy chained and verified they're snapped in place. The POE injector is powering Ubnt radios just fine. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373
