Six flashes, I'm trying to remember. I thought that means no power on
the input block. Could mean no sync. But I'm thinking power, which would
explain why your APs on that second injector won't come up at all.
Yes, you definitely need a SyncPipe connected to one of the
SyncInjectors. The sync daisy chain just means you can propagate the
sync pulse from a "master" SyncInjector to a number of other ones.
On 11/28/2014 8:07 PM, Josh Luthman via Af wrote:
Oh forgot to mention power - everything is 24vdc from the same circuit
(fuses are tested good from multimeter, 24v at every terminal). Note
two of the APs are working on one gig sync injector where the other
sync injector has 0 working APs.
Josh Luthman
Office: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
On Fri, Nov 28, 2014 at 9:05 PM, Josh Luthman
<[email protected] <mailto:[email protected]>> wrote:
SiteMonitor isn't showing any of the three expansion parts (poe
injector and 2x gig syncinjectors).
Is a SyncPipe Basic required for the syncinjectors to work? Or do
they have an GPS radio? I'm not seeing any documentation saying
it's necessary, but it's mentioning it a lot...
Will the gig syncinjectors still utilize 10 or 100 mbit?
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Fri, Nov 28, 2014 at 9:01 PM, Nate Burke via Af <[email protected]
<mailto:[email protected]>> wrote:
Does your site monitor show anything out of the ordinary? What
are you using to provide sync to the sync injector? The green
lights on both should blink once per second when they have sync.
On 11/28/2014 7:46 PM, Josh Luthman via Af wrote:
Here's a video, not sure what the blinking means?
https://www.youtube.com/watch?v=dME8A-H_590
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Fri, Nov 28, 2014 at 8:39 PM, Josh Luthman via Af
<[email protected] <mailto:[email protected]>> wrote:
*rb2011 with ports 2/3/4/5 set to hardware switch (ether2
master, 3/4/5 slave). Ports 6/7/8/9 are hardware switch
(ether6 master, 7/8/9 slave).
*From the rb2011 it goes to the Ethernet half of the
SyncInjector.
*From the POE half of the SyncInjector it goes to WB
gigeapc HV surge suppressors and then to the ePMP radios.
Two of the ePMP radios are powered up and running gige.
Neither are receiving CMM sync (top of the ePMP says "Not
receiving GPS sync"). The remaining 6 APs aren't even
powering up/linking up. Any ideas before I start
swapping parts? Is it OK to have the surge between
SyncInjectors and ePMP?
On top of all of this the SiteMonitor isn't talking to
the POE injector or the two Gig SyncInjectors. I have
them all daisy chained and verified they're snapped in
place. The POE injector is powering Ubnt radios just fine.
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
