What is the price on these magnet mounts? On Mon, Jul 31, 2017 at 2:07 PM, [email protected] < [email protected]> wrote:
> We used 250lbs magnets and it was a 3'x2' satellite dish non-pen. (My > mistake earlier.) We used a long J-arm > that we braced on two sides back to the mount so it was more of a tripod. > > On Mon, Jul 31, 2017 at 1:56 PM, <[email protected]> wrote: > >> I guess the magnet could have a stud with a slot in the end. Put >> threaded holes in the plate. You use a screw driver to adjust the magnet >> to plate and a lock nut to secure it once it is set. I would rather have >> a nut on the other side of the plate but hard to get a wrench into the >> center areas of a plate of any size. >> >> *From:* [email protected] >> *Sent:* Monday, July 31, 2017 11:40 AM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] Magnets on a warm summer day >> >> Yes, we had a backing nut. We did the outer edge, not the center. In >> total I think we had >> 10 magnets total. >> >> On Mon, Jul 31, 2017 at 1:23 PM, <[email protected]> wrote: >> >>> Did you have to adjust a backing nut for each magnet or did you just set >>> them all the same and rely on the mount to flex a bit? >>> Seems difficult to adjust magnet nuts in the center of the array as they >>> would be under the mounting plate, right? >>> >>> *From:* [email protected] >>> *Sent:* Monday, July 31, 2017 11:17 AM >>> *To:* [email protected] >>> *Subject:* Re: [AFMUG] Magnets on a warm summer day >>> >>> We followed the Magnemount design and took a typical 5'x5' non-pen and >>> drilled holes in it and put >>> a lot of magnets on it. The magnets had pretty long bolts on them so we >>> used that to adjust each >>> magnet so it would still sit flat on a curved surface. >>> >>> It's been holding a 2ft dish just fine for a couple years now. >>> >>> On Mon, Jul 31, 2017 at 1:13 PM, Chuck Hogg <[email protected]> wrote: >>> >>>> I was suggesting maybe stacking yours in a 4x4 pattern. >>>> >>>> Regards, >>>> Chuck >>>> >>>> On Mon, Jul 31, 2017 at 1:12 PM, <[email protected]> wrote: >>>> >>>>> I have. They have a good system. Very expensive system but it is >>>>> nicely designed. Trying to fill a niche. >>>>> >>>>> *From:* Chuck Hogg >>>>> *Sent:* Monday, July 31, 2017 9:05 AM >>>>> *To:* [email protected] >>>>> *Subject:* Re: [AFMUG] Magnets on a warm summer day >>>>> >>>>> Have you ever looked at Magnemount? They stack them together and make >>>>> it as a plate to increase surface mount. >>>>> >>>>> Regards, >>>>> Chuck >>>>> >>>>> On Mon, Jul 31, 2017 at 10:55 AM, Brian Sullivan < >>>>> [email protected]> wrote: >>>>> >>>>>> Nice video! Would love to see even more tests with stronger magnets. >>>>>> >>>>>> >>>>>> On 7/29/2017 6:16 PM, Jaime Solorza wrote: >>>>>> >>>>>> Very cool video... definitely a need for this product >>>>>> >>>>>> Jaime Solorza >>>>>> >>>>>> On Jul 29, 2017 3:37 PM, "Chuck McCown" <[email protected]> wrote: >>>>>> >>>>>>> >>>>>>> Magnetic Tower Mount >>>>>>> Some more destructive testing. >>>>>>> Magnetic mount for water towers and other structures. Check out my >>>>>>> latest video: >>>>>>> *Havin' Fun With Magnets <https://youtu.be/AHjHk9wjtFQ>* >>>>>>> >>>>>>> >>>>>>> >>>>>>> Come see all the fun stuff at *McCown Technology Corporation* >>>>>>> <http://www.mccowntech.com> >>>>>>> >>>>>>> <https://www.facebook.com/mccowntech/> >>>>>>> >>>>>>> *Copyright © 2017 McCown Technology Corporation, All rights >>>>>>> reserved.* >>>>>>> Thanks for attending the show. (Or being on the [email protected] list.) >>>>>>> See us at WispAmerica. Check out www.surge-protection.org and >>>>>>> www.afmug.com >>>>>>> >>>>>>> *Our mailing address is:* >>>>>>> McCown Technology Corporation >>>>>>> 8400 North HWY 36 >>>>>>> Lake Point, UT 84074 >>>>>>> >>>>>>> Add us to your address book >>>>>>> <http://wbmfg.us11.list-manage.com/vcard?u=98c1d7a210acd35707b9ba4d7&id=ed80c591e6> >>>>>>> >>>>>>> >>>>>>> Want to change how you receive these emails? >>>>>>> You can update your preferences >>>>>>> <http://mccowntech.us11.list-manage1.com/profile?u=98c1d7a210acd35707b9ba4d7&id=ed80c591e6&e=> >>>>>>> or unsubscribe from this list >>>>>>> <http://mccowntech.us11.list-manage.com/unsubscribe?u=98c1d7a210acd35707b9ba4d7&id=ed80c591e6&e=&c=72f193e926>. >>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>>> >>> >>> >> >> > >
