I can work it up. From: Kurt Fankhauser Sent: Monday, August 28, 2017 9:20 PM To: af@afmug.com Subject: Re: [AFMUG] Magnets on a warm summer day
What is the price on these magnet mounts? On Mon, Jul 31, 2017 at 2:07 PM, can...@believewireless.net <p...@believewireless.net> wrote: We used 250lbs magnets and it was a 3'x2' satellite dish non-pen. (My mistake earlier.) We used a long J-arm that we braced on two sides back to the mount so it was more of a tripod. On Mon, Jul 31, 2017 at 1:56 PM, <ch...@wbmfg.com> wrote: I guess the magnet could have a stud with a slot in the end. Put threaded holes in the plate. You use a screw driver to adjust the magnet to plate and a lock nut to secure it once it is set. I would rather have a nut on the other side of the plate but hard to get a wrench into the center areas of a plate of any size. From: can...@believewireless.net Sent: Monday, July 31, 2017 11:40 AM To: af@afmug.com Subject: Re: [AFMUG] Magnets on a warm summer day Yes, we had a backing nut. We did the outer edge, not the center. In total I think we had 10 magnets total. On Mon, Jul 31, 2017 at 1:23 PM, <ch...@wbmfg.com> wrote: Did you have to adjust a backing nut for each magnet or did you just set them all the same and rely on the mount to flex a bit? Seems difficult to adjust magnet nuts in the center of the array as they would be under the mounting plate, right? From: can...@believewireless.net Sent: Monday, July 31, 2017 11:17 AM To: af@afmug.com Subject: Re: [AFMUG] Magnets on a warm summer day We followed the Magnemount design and took a typical 5'x5' non-pen and drilled holes in it and put a lot of magnets on it. The magnets had pretty long bolts on them so we used that to adjust each magnet so it would still sit flat on a curved surface. It's been holding a 2ft dish just fine for a couple years now. On Mon, Jul 31, 2017 at 1:13 PM, Chuck Hogg <ch...@shelbybb.com> wrote: I was suggesting maybe stacking yours in a 4x4 pattern. Regards, Chuck On Mon, Jul 31, 2017 at 1:12 PM, <ch...@wbmfg.com> wrote: I have. They have a good system. Very expensive system but it is nicely designed. Trying to fill a niche. From: Chuck Hogg Sent: Monday, July 31, 2017 9:05 AM To: af@afmug.com Subject: Re: [AFMUG] Magnets on a warm summer day Have you ever looked at Magnemount? They stack them together and make it as a plate to increase surface mount. Regards, Chuck On Mon, Jul 31, 2017 at 10:55 AM, Brian Sullivan <installe...@foxvalley.net> wrote: Nice video! Would love to see even more tests with stronger magnets. On 7/29/2017 6:16 PM, Jaime Solorza wrote: Very cool video... definitely a need for this product Jaime Solorza On Jul 29, 2017 3:37 PM, "Chuck McCown" <ch...@wbmfg.com> wrote: Magnetic Tower Mount Some more destructive testing. Magnetic mount for water towers and other structures. Check out my latest video: Havin' Fun With Magnets Come see all the fun stuff at McCown Technology Corporation Copyright © 2017 McCown Technology Corporation, All rights reserved. Thanks for attending the show. (Or being on the af@afmug.com list.) See us at WispAmerica. Check out www.surge-protection.org and www.afmug.com Our mailing address is: McCown Technology Corporation 8400 North HWY 36 Lake Point, UT 84074 Add us to your address book Want to change how you receive these emails? You can update your preferences or unsubscribe from this list.