That is not bad pricing for what it is. On Wed, Aug 30, 2017 at 6:38 PM, Chuck McCown <[email protected]> wrote:
> I have not yet added up all the nuts bolts and washers but it will come in > at a list – retail price of between $200 and $225 MINUS MAGNETS > You just order it with the pull you need and I will add the magnets. A > 250 lb magnet costs me about $30 so you would need three of them. > I will not mark up the magnets because I do want this to be affordable as > possible. > > Howz that sound? > > *From:* Chuck McCown > *Sent:* Tuesday, August 29, 2017 8:22 AM > *To:* [email protected] > *Subject:* Re: [AFMUG] Magnets on a warm summer day > > I can work it up. > > *From:* Kurt Fankhauser > *Sent:* Monday, August 28, 2017 9:20 PM > *To:* [email protected] > *Subject:* Re: [AFMUG] Magnets on a warm summer day > > What is the price on these magnet mounts? > > On Mon, Jul 31, 2017 at 2:07 PM, [email protected] < > [email protected]> wrote: > >> We used 250lbs magnets and it was a 3'x2' satellite dish non-pen. (My >> mistake earlier.) We used a long J-arm >> that we braced on two sides back to the mount so it was more of a tripod. >> >> On Mon, Jul 31, 2017 at 1:56 PM, <[email protected]> wrote: >> >>> I guess the magnet could have a stud with a slot in the end. Put >>> threaded holes in the plate. You use a screw driver to adjust the magnet >>> to plate and a lock nut to secure it once it is set. I would rather have >>> a nut on the other side of the plate but hard to get a wrench into the >>> center areas of a plate of any size. >>> >>> *From:* [email protected] >>> *Sent:* Monday, July 31, 2017 11:40 AM >>> *To:* [email protected] >>> *Subject:* Re: [AFMUG] Magnets on a warm summer day >>> >>> Yes, we had a backing nut. We did the outer edge, not the center. In >>> total I think we had >>> 10 magnets total. >>> >>> On Mon, Jul 31, 2017 at 1:23 PM, <[email protected]> wrote: >>> >>>> Did you have to adjust a backing nut for each magnet or did you just >>>> set them all the same and rely on the mount to flex a bit? >>>> Seems difficult to adjust magnet nuts in the center of the array as >>>> they would be under the mounting plate, right? >>>> >>>> *From:* [email protected] >>>> *Sent:* Monday, July 31, 2017 11:17 AM >>>> *To:* [email protected] >>>> *Subject:* Re: [AFMUG] Magnets on a warm summer day >>>> >>>> We followed the Magnemount design and took a typical 5'x5' non-pen and >>>> drilled holes in it and put >>>> a lot of magnets on it. The magnets had pretty long bolts on them so we >>>> used that to adjust each >>>> magnet so it would still sit flat on a curved surface. >>>> >>>> It's been holding a 2ft dish just fine for a couple years now. >>>> >>>> On Mon, Jul 31, 2017 at 1:13 PM, Chuck Hogg <[email protected]> wrote: >>>> >>>>> I was suggesting maybe stacking yours in a 4x4 pattern. >>>>> >>>>> Regards, >>>>> Chuck >>>>> >>>>> On Mon, Jul 31, 2017 at 1:12 PM, <[email protected]> wrote: >>>>> >>>>>> I have. They have a good system. Very expensive system but it is >>>>>> nicely designed. Trying to fill a niche. >>>>>> >>>>>> *From:* Chuck Hogg >>>>>> *Sent:* Monday, July 31, 2017 9:05 AM >>>>>> *To:* [email protected] >>>>>> *Subject:* Re: [AFMUG] Magnets on a warm summer day >>>>>> >>>>>> Have you ever looked at Magnemount? They stack them together and >>>>>> make it as a plate to increase surface mount. >>>>>> >>>>>> Regards, >>>>>> Chuck >>>>>> >>>>>> On Mon, Jul 31, 2017 at 10:55 AM, Brian Sullivan < >>>>>> [email protected]> wrote: >>>>>> >>>>>>> Nice video! Would love to see even more tests with stronger >>>>>>> magnets. >>>>>>> >>>>>>> >>>>>>> On 7/29/2017 6:16 PM, Jaime Solorza wrote: >>>>>>> >>>>>>> Very cool video... definitely a need for this product >>>>>>> >>>>>>> Jaime Solorza >>>>>>> >>>>>>> On Jul 29, 2017 3:37 PM, "Chuck McCown" <[email protected]> wrote: >>>>>>> >>>>>>>> >>>>>>>> Magnetic Tower Mount >>>>>>>> Some more destructive testing. >>>>>>>> Magnetic mount for water towers and other structures. Check out >>>>>>>> my latest video: >>>>>>>> *Havin' Fun With Magnets <https://youtu.be/AHjHk9wjtFQ>* >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> Come see all the fun stuff at *McCown Technology Corporation* >>>>>>>> <http://www.mccowntech.com> >>>>>>>> >>>>>>>> <https://www.facebook.com/mccowntech/> >>>>>>>> >>>>>>>> *Copyright © 2017 McCown Technology Corporation, All rights >>>>>>>> reserved.* >>>>>>>> Thanks for attending the show. (Or being on the [email protected] >>>>>>>> list.) See us at WispAmerica. Check out www.surge-protection.org >>>>>>>> and www.afmug.com >>>>>>>> >>>>>>>> *Our mailing address is:* >>>>>>>> McCown Technology Corporation >>>>>>>> 8400 North HWY 36 >>>>>>>> Lake Point, UT 84074 >>>>>>>> >>>>>>>> Add us to your address book >>>>>>>> <http://wbmfg.us11.list-manage.com/vcard?u=98c1d7a210acd35707b9ba4d7&id=ed80c591e6> >>>>>>>> >>>>>>>> >>>>>>>> Want to change how you receive these emails? >>>>>>>> You can update your preferences >>>>>>>> <http://mccowntech.us11.list-manage1.com/profile?u=98c1d7a210acd35707b9ba4d7&id=ed80c591e6&e=> >>>>>>>> or unsubscribe from this list >>>>>>>> <http://mccowntech.us11.list-manage.com/unsubscribe?u=98c1d7a210acd35707b9ba4d7&id=ed80c591e6&e=&c=72f193e926>. >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>> >>>>>> >>>>> >>>>> >>>> >>>> >>> >>> >> >> > >
