I think you're right on the switch. I had issues that were caused by a faulty switch and pushing the button cured them. My button had broken but I put a paperclip in the hole and pressed it and it started working again.
On Wed, May 18, 2016 at 4:23 PM, Bruce J keeler <[email protected]> wrote: > If I recall, there's one of those safety thingies before the pressurestat. > Look for gizmos on the boilers with two wires and tiny red buttons in the > center. Try pushing those buttons down. That's pretty much my first step in > any 'something not getting power' scenarios. > > I may be misremembering, of course. Trace the p-state input back and check > the voltage at anything it's passing through. > On 5/18/2016 7:19 AM, Benjamin McCafferty wrote: > > By "the board" I assume you mean the Giemme, yes? Or the PID or digital > thermostat, whichever it has? > Either way, to my thinking, if you have power into the Giemme, and no > power out, that seems like the source of the issue. Are you sure you're > measuring the right wire/terminal on the p-stat, i.e. the input side and > not the output side? (I only ask because....ahem....I've *heard* of people > making this mistake....of course it wasn't me...). Also, are you checking > the p-stat on the output side, thinking the p-stat is good, I.e. could it > be bad and therefore only input voltage tells you anything? > > Are the wires to the correct terminals on the Giemme? The replacement is > slightly different than the original, and the numbers do not all match up > the same as the old one. There is a diagram if you need it. > > > If that's all fine, perhaps ask WLL if there's a warranty on the Giemme > board--I recently found a guy here in WA that rebuilds them, but it's as > expensive as getting a new one (about $75). Pretty unusual for one to fail > that fast. > > Keep us posted. > > Best, > bmc > Sent from my apple IIe > > On May 18, 2016, at 05:09, Eric S <[email protected]> wrote: > > A little more info- > > It does have power going in to the control board. When I turned it on, it > filled the boilers. Took almost the whole reservoir, so assume they are > both full. Then after the pump kicked off it didn't switch over to > heating. > > On Tuesday, May 17, 2016 at 4:02:01 PM UTC-5, Eric S wrote: >> >> working on getting this new to me brewtus going. >> >> I am working my way through the WLL video about checking electronic >> systems, and I am not getting power to the pressure stat. >> >> Is it likely the whole board, or is there something else I can check in >> there. The board on this machine was replaced back in November or so. >> >> Thanks >> > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to <[email protected]> > [email protected]. > Visit this group at https://groups.google.com/group/brewtus. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at https://groups.google.com/group/brewtus. > For more options, visit https://groups.google.com/d/optout. > > > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at https://groups.google.com/group/brewtus. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at https://groups.google.com/group/brewtus. For more options, visit https://groups.google.com/d/optout.
