Sorry, a word missing:
, if your best efforts to find a documented rationale to not apply the
requirement FAIL,
======================================================================================
Best wishes John Woodgate OOO-Own Opinions Only
www.woodjohn.uk
Rayleigh, Essex UK
I hear, and I forget. I see, and I remember. I do, and I understand.
Xunzi (340 - 245 BC)
On 2022-12-02 21:04, John Woodgate wrote:
Very good advice. There is a 'dumb' fallback, if your best efforts to
find a documented rationale to not apply the requirement, is to
consider how much extra it costs to comply with it, compared to the
cost of trying to find a reason not to comply with it.
For example, I found that replacing the inter-winding insulation in a
transformer by PET tape, which has a very high dielectric strength,
met the requirement that I considered unnecessary by a very large
margin, and incidentally was marginally less costly.
======================================================================================
Best wishes John Woodgate OOO-Own Opinions Only
www.woodjohn.uk
Rayleigh, Essex UK
I hear, and I forget. I see, and I remember. I do, and I understand.
Xunzi (340 - 245 BC)
On 2022-12-02 19:15, Joe Randolph wrote:
Hi Steve:
I work mostly with the 60950-1 and 62368-1 standards for ITE, so I’m
not familiar with the details of the requirements in 61010-1.
That being said, I’ve seen many cases where someone misinterpreted
the creepage/clearance/dielectric requirements in 60950-1 and
62368-1, not realizing that their specific configuration was exempt
from those requirements. So, I’d like to have more details on the
specific requirement that concern you, and the specific circuit where
you are trying to apply this requirement.
Is the 100 Vdc secondary fully floating with respect to the ground at
the AC mains, or is it referenced to the AC mains ground?
Does the AC mains connection use an ordinary “Pluggable Type A” plug
or is it hardwired?
If it uses a Type A plug, does that plug have a ground pin?
These are just some of the factors that can affect how the isolation
requirements apply to this specific design.
If the AC mains ground is obtained from a grounded Type A plug, there
is a fault scenario that */might/* be behind the requirement that
concerns you. This is case where the presumed ground in the AC
outlet is missing, or the user has installed a “cheater adapter” to
convert the 3-prong plug to a 2-prong plug.
In this case the ground node in the equipment becomes a floating
node, which creates certain potential scenarios that might create the
need for the requirement that concerns you.
I agree with you that it’s best to always make sure that understand
the rationale behind any requirement that is giving you trouble.
Once you know the rationale, you will better understand whether the
requirement should apply to your specific application.
Joe Randolph
Telecom Design Consultant
Randolph Telecom, Inc.
781-721-2848 (USA)
[email protected] <mailto:[email protected]>
http://www.randolph-telecom.com <http://www.randolph-telecom.com/>
*From:*Steve Brody [mailto:[email protected]]
*Sent:* Thursday, December 1, 2022 3:51 PM
*To:* [email protected]
*Subject:* [PSES] Secondary creepage/clearance
I have a client who has a secondary pwb that has traces and vias that
may have 100 vdc on them adjacent to ground.
Per 61010-1 there is a requirement for spacing and/or dielectric
test, both depending on what the mains voltage is.
The question is why is the mains voltage a consideration or concern
if the 100vdc secondary voltage is several layers of impedance and
circuitry from the mains?
Is it a concern that a surge on the mains would trickle down to the
secondary circuit, or is there another reason/rationale?
I suggested that a dielectric test per Table 6 [in A1] would suffice
and put the issue to rest for this product, but the question from the
designers remains as to why is it a concern in the standard of what
the mains voltage is.
Is there anything in the standard, that I haven't found, that does
not require Table 6 to be followed if there is no way for a mains
surge to impact the secondary voltage?
I look to the experts for an explanation.
Thanks,
Steve Brody
[email protected]
C - 603 617 9116
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <[email protected]>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe) <http://www.ieee-pses.org/list.html>
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Mike Cantwell <[email protected]>
For policy questions, send mail to:
Jim Bacher <[email protected]>
David Heald <[email protected]>
------------------------------------------------------------------------
To unsubscribe from the EMC-PSTC list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC&A=1
<https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC&A=1>
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <[email protected]>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe) <http://www.ieee-pses.org/list.html>
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Mike Cantwell <[email protected]>
For policy questions, send mail to:
Jim Bacher <[email protected]>
David Heald <[email protected]>
------------------------------------------------------------------------
To unsubscribe from the EMC-PSTC list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC&A=1
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <[email protected]>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe) <http://www.ieee-pses.org/list.html>
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Mike Cantwell <[email protected]>
For policy questions, send mail to:
Jim Bacher <[email protected]>
David Heald <[email protected]>
------------------------------------------------------------------------
To unsubscribe from the EMC-PSTC list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC&A=1
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society emc-pstc discussion
list. To post a message to the list, send your e-mail to <[email protected]>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Mike Cantwell <[email protected]>
For policy questions, send mail to:
Jim Bacher: <[email protected]>
David Heald: <[email protected]>
_________________________________________________
To unsubscribe from the EMC-PSTC list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC&A=1
