Is that what you meant? http://makezine.com/2016/03/25/dont-glue-anything-without-handy-reference-ch art/
> -----Original Message----- > From: R.L. Wurdack [mailto:di...@nwlink.com] > Sent: Tuesday, August 30, 2016 2:05 PM > To: Enhanced Machine Controller (EMC) > Subject: Re: [Emc-users] Silly Q about glues > > Sorry, Gene. My mags are down at the ranch and I'm picking apples up here at > the farm. I'll look up the reference as soon as I have a chance. > > Richard. > > > ----- Original Message ----- > From: "Gene Heskett" <ghesk...@shentel.net> > To: <emc-users@lists.sourceforge.net> > Sent: Thursday, August 25, 2016 10:00 AM > Subject: Re: [Emc-users] Silly Q about glues > > > > On Thursday 25 August 2016 12:35:40 R.L. Wurdack wrote: > > > >> ""Make"" magazine a while back had a nice table of glues vs > >> applications that I found useful. > >> > >> Dick > >> > > I just spent half an hour clicking "more" without finding it. > > > > Thank you for trying. > >> > >> ----- Original Message ----- > >> From: "Gene Heskett" <ghesk...@shentel.net> > >> To: <emc-users@lists.sourceforge.net> > >> Sent: Thursday, August 25, 2016 9:25 AM > >> Subject: [Emc-users] Silly Q about glues > >> > >> > Greetings; > >> > > >> > Trying to carve the toolpost support for the little monster, on the > >> > little monster. I had it lopsided in the chuck, roughly centered on > >> > the QC's bolt hole. But that meant the chuck jaws were turned around > >> > and I couldn't get to the bottom 9/16 of an inch because of flying > >> > jaws . I needed the cutaway down to perhaps 3mm of the carriage > >> > sled, so I wrote some gcode to cut the hollowed out curve. I was > >> > going to see if I could put it on the faceplate, but its a full 7" > >> > in diameter and hits the motor & electronics box on the back of the > >> > lathe. > >> > > >> > So that was out. I put the 5" 4 jaw back on, w/o the jaws, putting a > >> > live center in the tailstock, I ran it out far enough to get some > >> > saddle movement room but left it pushing about 100lbs worth and ran > >> > a line of fresh superglue all the way around it.. > >> > > >> > Setting up the start-stop and done settings in my gcode, I had a > >> > good pressure on it, and had cleaned the face of the chuck with > >> > acetone, so superglue should have stuck it for a non-slip grip. > >> > Peeled it loose on the third touch of the tool. 3 times now, with > >> > longer setting times each time. > >> > > >> > If I can find it, I've some double stick tape, or does someone else > >> > have an even better idea? > >> > > >> > Thanks. > >> > > >> > Cheers, Gene Heskett > >> > -- > >> > "There are four boxes to be used in defense of liberty: > >> > soap, ballot, jury, and ammo. Please use in that order." > >> > -Ed Howdershelt (Author) > >> > Genes Web page <http://geneslinuxbox.net:6309/gene> > >> > > >> > -------------------------------------------------------------------- > >> >---------- _______________________________________________ > >> > Emc-users mailing list > >> > Emc-users@lists.sourceforge.net > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> ---------------------------------------------------------------------- > >>-------- _______________________________________________ > >> Emc-users mailing list > >> Emc-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > Cheers, Gene Heskett > > -- > > "There are four boxes to be used in defense of liberty: > > soap, ballot, jury, and ammo. Please use in that order." > > -Ed Howdershelt (Author) > > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > > ---------------------------------------------------------------------------- -- > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > ---------------------------------------------------------------------------- -- > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users