On Tuesday 30 August 2016 16:15:51 Ken Strauss wrote: > Is that what you meant? > http://makezine.com/2016/03/25/dont-glue-anything-without-handy-refere >nce-ch art/ > Handy, like sliced bread. Bookmarked. Thanks Ken.
> > -----Original Message----- > > From: R.L. Wurdack [mailto:[email protected]] > > Sent: Tuesday, August 30, 2016 2:05 PM > > To: Enhanced Machine Controller (EMC) > > Subject: Re: [Emc-users] Silly Q about glues > > > > Sorry, Gene. My mags are down at the ranch and I'm picking apples up > > here > > at > > > the farm. I'll look up the reference as soon as I have a chance. > > > > Richard. > > > > > > ----- Original Message ----- > > From: "Gene Heskett" <[email protected]> > > To: <[email protected]> > > Sent: Thursday, August 25, 2016 10:00 AM > > Subject: Re: [Emc-users] Silly Q about glues > > > > > On Thursday 25 August 2016 12:35:40 R.L. Wurdack wrote: > > >> ""Make"" magazine a while back had a nice table of glues vs > > >> applications that I found useful. > > >> > > >> Dick > > > > > > I just spent half an hour clicking "more" without finding it. > > > > > > Thank you for trying. > > > > > >> ----- Original Message ----- > > >> From: "Gene Heskett" <[email protected]> > > >> To: <[email protected]> > > >> Sent: Thursday, August 25, 2016 9:25 AM > > >> Subject: [Emc-users] Silly Q about glues > > >> > > >> > Greetings; > > >> > > > >> > Trying to carve the toolpost support for the little monster, on > > >> > the little monster. I had it lopsided in the chuck, roughly > > >> > centered on the QC's bolt hole. But that meant the chuck jaws > > >> > were turned around and I couldn't get to the bottom 9/16 of an > > >> > inch because of flying jaws . I needed the cutaway down to > > >> > perhaps 3mm of the carriage sled, so I wrote some gcode to cut > > >> > the hollowed out curve. I was going to see if I could put it on > > >> > the faceplate, but its a full 7" in diameter and hits the motor > > >> > & electronics box on the back of the lathe. > > >> > > > >> > So that was out. I put the 5" 4 jaw back on, w/o the jaws, > > >> > putting a live center in the tailstock, I ran it out far enough > > >> > to get some saddle movement room but left it pushing about > > >> > 100lbs worth and ran a line of fresh superglue all the way > > >> > around it.. > > >> > > > >> > Setting up the start-stop and done settings in my gcode, I had > > >> > a good pressure on it, and had cleaned the face of the chuck > > >> > with acetone, so superglue should have stuck it for a non-slip > > >> > grip. Peeled it loose on the third touch of the tool. 3 times > > >> > now, with longer setting times each time. > > >> > > > >> > If I can find it, I've some double stick tape, or does someone > > >> > else have an even better idea? > > >> > > > >> > Thanks. > > >> > > > >> > Cheers, Gene Heskett > > >> > -- > > >> > "There are four boxes to be used in defense of liberty: > > >> > soap, ballot, jury, and ammo. Please use in that order." > > >> > -Ed Howdershelt (Author) > > >> > Genes Web page <http://geneslinuxbox.net:6309/gene> > > >> > > > >> > --------------------------------------------------------------- > > >> >----- ---------- _______________________________________________ > > >> > Emc-users mailing list > > >> > [email protected] > > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > >> ----------------------------------------------------------------- > > >>----- -------- _______________________________________________ > > >> Emc-users mailing list > > >> [email protected] > > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > Cheers, Gene Heskett > > > -- > > > "There are four boxes to be used in defense of liberty: > > > soap, ballot, jury, and ammo. Please use in that order." > > > -Ed Howdershelt (Author) > > > Genes Web page <http://geneslinuxbox.net:6309/gene> > > ---------------------------------------------------------------------- >------ -- > > > > _______________________________________________ > > > Emc-users mailing list > > > [email protected] > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > ---------------------------------------------------------------------- >------ -- > > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > ---------------------------------------------------------------------- >-------- _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
