> Hi,
>
> I'm getting a no eeprom present in my log file for my PVR-150. I've tried
> forcing newi2c to both 0 and 1 with no success. If I do: newi2c=1, loading
> the module takes seconds. If I do: newi2c=0, loading the module take 8
> minutes.
I suspect broken hardware: it is not just the eeprom that is missing, so I
recommend testing it in a Windows box first.
Regards,
Hans
>
> Here is the output from lspci -vvv :
>
> 02:09.0 Multimedia video controller: Internext Compression Inc iTVC16
> (CX23416) MPEG-2 Encoder (rev 01)
> Subsystem: Hauppauge computer works Inc. Unknown device b7f3
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 16 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> Here is the output in syslog:
>
> May 29 21:28:46 mythslave ivtv: ==================== START INIT IVTV
> ====================
> May 29 21:28:46 mythslave ivtv: version 0.10.1 (tagged release) loading
> May 29 21:28:46 mythslave ivtv: Linux version: 2.6.19-gentoo-r5 SMP
> mod_unload 686 REGPARM 4KSTACKS
> May 29 21:28:46 mythslave ivtv: In case of problems please include the
> debug info between
> May 29 21:28:46 mythslave ivtv: the START INIT IVTV and END INIT IVTV
> lines, along with
> May 29 21:28:46 mythslave ivtv: any module options, when mailing the
> ivtv-users mailinglist.
> May 29 21:28:46 mythslave ivtv0: Autodetected Hauppauge card (cx23416
> based)
> May 29 21:28:46 mythslave ivtv0 info: base addr: 0xf0000000
> May 29 21:28:46 mythslave ivtv0 info: Enabling pci device
> May 29 21:28:46 mythslave ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 17
> (level, low) -> IRQ 17
> May 29 21:28:46 mythslave ivtv0 info: Attempting to enable Bus Mastering
> May 29 21:28:46 mythslave ivtv0 info: Bus Mastering Enabled.
> May 29 21:28:46 mythslave ivtv0 info: 22 (rev 1) at 02:09.0, irq: 17,
> latency: 64, memory: 0xf0000000
> May 29 21:28:46 mythslave ivtv0 info: attempting ioremap at 0xf0000000 len
> 0x00800000
> May 29 21:28:46 mythslave ivtv0 info: attempting ioremap at 0xf2000000 len
> 0x00010000
> May 29 21:28:46 mythslave ivtv0 info: Preparing for firmware halt.
> May 29 21:28:46 mythslave ivtv0 info: Stopping VDM
> May 29 21:28:46 mythslave ivtv0 info: Stopping AO
> May 29 21:28:46 mythslave ivtv0 info: pinging (?) APU
> May 29 21:28:46 mythslave ivtv0 info: Stopping VPU
> May 29 21:28:46 mythslave ivtv0 info: Resetting Hw Blocks
> May 29 21:28:46 mythslave ivtv0 info: Stopping SPU
> May 29 21:28:46 mythslave ivtv0 info: init Encoder SDRAM pre-charge
> May 29 21:28:46 mythslave ivtv0 info: init Encoder SDRAM refresh to 1us
> May 29 21:28:46 mythslave ivtv0 info: Sleeping for 600ms (600 recommended)
> May 29 21:28:46 mythslave ivtv0 info: Loading encoder image
> May 29 21:28:46 mythslave ivtv0: loaded v4l-cx2341x-enc.fw firmware
> (376836 bytes)
> May 29 21:28:46 mythslave ivtv0 info: Getting firmware version..
> May 29 21:28:47 mythslave ivtv0: Encoder revision: 0x02060039
> May 29 21:28:47 mythslave ivtv0 info: GPIO initial dir: 0000df00 out:
> 000026f3
> May 29 21:28:47 mythslave ivtv0 info: activating i2c...
> May 29 21:28:47 mythslave ivtv0 info: Active card count: 1.
> May 29 21:28:47 mythslave ivtv0 info: Loaded module tveeprom
> May 29 21:28:47 mythslave tveeprom 1-0050: Huh, no eeprom present
> (err=-121)?
> May 29 21:28:47 mythslave tveeprom 1-0050: Encountered bad packet header
> [87]. Corrupt or not a Hauppauge eeprom.
> May 29 21:28:47 mythslave ivtv0: Invalid EEPROM
> May 29 21:28:47 mythslave ivtv0 info: Loaded module tuner
> May 29 21:28:47 mythslave ivtv0 info: Loaded module cx25840
> May 29 21:28:47 mythslave ivtv0 info: Loaded module wm8775
> May 29 21:28:47 mythslave ivtv0: Registered device video0 for encoder MPEG
> (4 MB)
> May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder MPEG stream:
> 128 x 32768 buffers (4096kB total)
> May 29 21:28:47 mythslave ivtv0: Registered device video32 for encoder YUV
> (2 MB)
> May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder YUV stream: 194
> x 10800 buffers (2046kB total)
> May 29 21:28:47 mythslave ivtv0: Registered device vbi0 for encoder VBI (1
> MB)
> May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder VBI stream: 60
> x 17472 buffers (1023kB total)
> May 29 21:28:47 mythslave ivtv0: Registered device video24 for encoder PCM
> audio (1 MB)
> May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder PCM audio
> stream: 227 x 4608 buffers (1021kB total)
> May 29 21:28:47 mythslave ivtv0: Registered device radio0 for encoder
> radio
> May 29 21:28:47 mythslave ivtv0 info: Starting Threads
> May 29 21:28:47 mythslave ivtv0 info: Changing input from 1 to 0
> May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) not
> found for command 0xc008561c!
> May 29 21:28:47 mythslave ivtv0 info: Mute
> May 29 21:28:47 mythslave ivtv0: i2c addr 0x44 not found for command
> 0x4008646f!
> May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000020 (wm8775) not
> found for command 0x4008646d!
> May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) not
> found for command 0x4008646d!
> May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) not
> found for command 0xc008561c!
> May 29 21:28:47 mythslave ivtv0 info: Unmute
> May 29 21:28:47 mythslave ivtv0 info: Switching standard to 1000.
> May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) not
> found for command 0xc008561c!
> May 29 21:28:47 mythslave ivtv0 info: Mute
> May 29 21:28:47 mythslave ivtv0 info: v4l2 ioctl: set frequency 1076
> May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) not
> found for command 0xc008561c!
> May 29 21:28:47 mythslave ivtv0 info: Unmute
> May 29 21:28:47 mythslave ivtv0: Initialized Hauppauge WinTV PVR-150, card
> #0
> May 29 21:28:47 mythslave ivtv: ==================== END INIT IVTV
> ====================
>
> This shows 10.1, but 10.2 does the same thing
>
> Any help would be appreciated.
>
> Gerald
>
>
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
