The behaviour I have had is identical to this, with newi2c=-1 or 0 it takes about >5 minutest to load the module, with newi2c=1 it takes seconds. -Nathaniel
On May 29, 2007, at 10:29 PM, Gerald Brandt wrote: > Hi, > > I'm getting a no eeprom present in my log file for my PVR-150. > I've tried forcing newi2c to both 0 and 1 with no success. If I > do: newi2c=1, loading the module takes seconds. If I do: newi2c=0, > loading the module take 8 minutes. > > Here is the output from lspci -vvv: > > 02:09.0 Multimedia video controller: Internext Compression Inc > iTVC16 (CX23416) MPEG-2 Encoder (rev 01) > Subsystem: Hauppauge computer works Inc. Unknown device b7f3 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > ParErr- Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 16 > bytes > Interrupt: pin A routed to IRQ 17 > Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME > (D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > Here is the output in syslog: > > May 29 21:28:46 mythslave ivtv: ==================== START INIT > IVTV ==================== > May 29 21:28:46 mythslave ivtv: version 0.10.1 (tagged release) > loading > May 29 21:28:46 mythslave ivtv: Linux version: 2.6.19-gentoo-r5 > SMP mod_unload 686 REGPARM 4KSTACKS > May 29 21:28:46 mythslave ivtv: In case of problems please include > the debug info between > May 29 21:28:46 mythslave ivtv: the START INIT IVTV and END INIT > IVTV lines, along with > May 29 21:28:46 mythslave ivtv: any module options, when mailing > the ivtv-users mailinglist. > May 29 21:28:46 mythslave ivtv0: Autodetected Hauppauge card > (cx23416 based) > May 29 21:28:46 mythslave ivtv0 info: base addr: 0xf0000000 > May 29 21:28:46 mythslave ivtv0 info: Enabling pci device > May 29 21:28:46 mythslave ACPI: PCI Interrupt 0000:02:09.0[A] -> > GSI 17 (level, low) -> IRQ 17 > May 29 21:28:46 mythslave ivtv0 info: Attempting to enable Bus > Mastering > May 29 21:28:46 mythslave ivtv0 info: Bus Mastering Enabled. > May 29 21:28:46 mythslave ivtv0 info: 22 (rev 1) at 02:09.0, irq: > 17, latency: 64, memory: 0xf0000000 > May 29 21:28:46 mythslave ivtv0 info: attempting ioremap at > 0xf0000000 len 0x00800000 > May 29 21:28:46 mythslave ivtv0 info: attempting ioremap at > 0xf2000000 len 0x00010000 > May 29 21:28:46 mythslave ivtv0 info: Preparing for firmware halt. > May 29 21:28:46 mythslave ivtv0 info: Stopping VDM > May 29 21:28:46 mythslave ivtv0 info: Stopping AO > May 29 21:28:46 mythslave ivtv0 info: pinging (?) APU > May 29 21:28:46 mythslave ivtv0 info: Stopping VPU > May 29 21:28:46 mythslave ivtv0 info: Resetting Hw Blocks > May 29 21:28:46 mythslave ivtv0 info: Stopping SPU > May 29 21:28:46 mythslave ivtv0 info: init Encoder SDRAM pre-charge > May 29 21:28:46 mythslave ivtv0 info: init Encoder SDRAM refresh to > 1us > May 29 21:28:46 mythslave ivtv0 info: Sleeping for 600ms (600 > recommended) > May 29 21:28:46 mythslave ivtv0 info: Loading encoder image > May 29 21:28:46 mythslave ivtv0: loaded v4l-cx2341x-enc.fw firmware > (376836 bytes) > May 29 21:28:46 mythslave ivtv0 info: Getting firmware version.. > May 29 21:28:47 mythslave ivtv0: Encoder revision: 0x02060039 > May 29 21:28:47 mythslave ivtv0 info: GPIO initial dir: 0000df00 > out: 000026f3 > May 29 21:28:47 mythslave ivtv0 info: activating i2c... > May 29 21:28:47 mythslave ivtv0 info: Active card count: 1. > May 29 21:28:47 mythslave ivtv0 info: Loaded module tveeprom > May 29 21:28:47 mythslave tveeprom 1-0050: Huh, no eeprom present > (err=-121)? > May 29 21:28:47 mythslave tveeprom 1-0050: Encountered bad packet > header [87]. Corrupt or not a Hauppauge eeprom. > May 29 21:28:47 mythslave ivtv0: Invalid EEPROM > May 29 21:28:47 mythslave ivtv0 info: Loaded module tuner > May 29 21:28:47 mythslave ivtv0 info: Loaded module cx25840 > May 29 21:28:47 mythslave ivtv0 info: Loaded module wm8775 > May 29 21:28:47 mythslave ivtv0: Registered device video0 for > encoder MPEG (4 MB) > May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder MPEG > stream: 128 x 32768 buffers (4096kB total) > May 29 21:28:47 mythslave ivtv0: Registered device video32 for > encoder YUV (2 MB) > May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder YUV > stream: 194 x 10800 buffers (2046kB total) > May 29 21:28:47 mythslave ivtv0: Registered device vbi0 for encoder > VBI (1 MB) > May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder VBI > stream: 60 x 17472 buffers (1023kB total) > May 29 21:28:47 mythslave ivtv0: Registered device video24 for > encoder PCM audio (1 MB) > May 29 21:28:47 mythslave ivtv0 info: Allocate DMA encoder PCM > audio stream: 227 x 4608 buffers (1021kB total) > May 29 21:28:47 mythslave ivtv0: Registered device radio0 for > encoder radio > May 29 21:28:47 mythslave ivtv0 info: Starting Threads > May 29 21:28:47 mythslave ivtv0 info: Changing input from 1 to 0 > May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) > not found for command 0xc008561c! > May 29 21:28:47 mythslave ivtv0 info: Mute > May 29 21:28:47 mythslave ivtv0: i2c addr 0x44 not found for > command 0x4008646f! > May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000020 (wm8775) > not found for command 0x4008646d! > May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) > not found for command 0x4008646d! > May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) > not found for command 0xc008561c! > May 29 21:28:47 mythslave ivtv0 info: Unmute > May 29 21:28:47 mythslave ivtv0 info: Switching standard to 1000. > May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) > not found for command 0xc008561c! > May 29 21:28:47 mythslave ivtv0 info: Mute > May 29 21:28:47 mythslave ivtv0 info: v4l2 ioctl: set frequency 1076 > May 29 21:28:47 mythslave ivtv0: i2c hardware 0x00000001 (cx2584x) > not found for command 0xc008561c! > May 29 21:28:47 mythslave ivtv0 info: Unmute > May 29 21:28:47 mythslave ivtv0: Initialized Hauppauge WinTV > PVR-150, card #0 > May 29 21:28:47 mythslave ivtv: ==================== END INIT > IVTV ==================== > > This shows 10.1, but 10.2 does the same thing > > Any help would be appreciated. > > Gerald > > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users ----- Nathaniel Madura Engineer in Research UMTRI - Biosciences 734-936-1109 [EMAIL PROTECTED] _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
