On Wed, 13 Jan 1999, Chris Karakas wrote:
> OK, then try adding the following line in your /etc/conf.modules:
>
> options bpck-fdc ft_fdc_parport=1
hmm, it found the drive again, but still complains about "No polling
interrupt"... :(
------------
(c) 1993-1996 Bas Laarhoven
(c) 1995-1996 Kai Harrekilde-Petersen
(c) 1996-1998 Claus-Justus Heine ([EMAIL PROTECTED])
QIC-117 driver for QIC-40/80/3010/3020/Ditto 2GB/MAX floppy tape drives.
Compiled for Linux version 2.1.130
installing QIC-117 floppy tape hardware drive ...
ftape_init @ 0xc183c220.
zftape for ftape v4.03-pre-2 11/05/98
(c) 1996, 1997 Claus-Justus Heine ([EMAIL PROTECTED])
vfs interface for ftape floppy tape driver.
Support for QIC-113 compatible volume table.
Compiled for Linux version 2.1.130 with versioned symbols
[000] zftape-init.c (zft_init) - zft_init @ 0xc186e430.
[001] zftape-init.c (zft_init) - installing zftape VFS interface for ftape driver
....
bpck-fdc.c: bpck_fdc_register @ 0xc187b380
[002] fdc-io.c (fdc_register_R4f14b5b4) - Probing for bpck-fdc tape drive slot 0.
[003] 0 fdc-parport.h (ft_parport_probe) - dev: c0913110.
[004] 0 fdc-parport.h (ft_parport_probe) - irq: 5.
[005] 0 fdc-parport.h (ft_parport_probe) - port: 278.
[006] 0 bpck-fdc.c (bpck_fdc_probe) - Bpck parallel port tape drive interface
for ftape v4.03-pre-2 11/05/98.
[007] bpck-fdc.c (bpck_fdc_switch_proto) - Need delay 1 for proto 0.
[008] bpck-fdc.c (bpck_fdc_switch_proto) - Need delay 1 for proto 1.
[009] bpck-fdc.c (bpck_fdc_switch_proto) - Need delay 1 for proto 1.
[010] bpck-fdc.c (bpck_fdc_log_adapter) - bpck floppy tape at 0x278, mode 1
(8-bit), delay 1.
[011] 0 fdc-parport.h (ft_parport_probe) - base: 0x278, irq: 5, number: 1.
[012] 0 ftape-buffer.c (add_one_buffer) - buffer nr #1 @ c0da2a30, dma area @
c187e000.
[013] 0 ftape-buffer.c (add_one_buffer) - buffer nr #2 @ c08455c0, dma area @
c187e000.
[014] 0 ftape-buffer.c (add_one_buffer) - buffer nr #3 @ c0845650, dma area @
c187e000.
[015] 0 ftape-buffer.c (add_one_buffer) - buffer nr #4 @ c0845530, dma area @
c187e000.
[016] 0 ftape-calibr.c (ftape_calibrate) - calibr_count: 394, calibr_time: 9948 us.
[017] 0 ftape-calibr.c (ftape_calibrate) - TC for `fdc_wait()' = 25248 nsec (at
394 counts).
[018] 0 fdc-io.c (fdc_reset) - no drive polling interrupt!.
[019] 0 fdc-io.c (fdc_probe) - Type 82077AA FDC found.
[020] 0 fdc-io.c (fdc_reset) - no drive polling interrupt!.
[021] 0 ftape-ctl.c (ftape_activate_drive) - No tape drive found.
[022] 0 fdc-io.c (fdc_reset) - no drive polling interrupt!.
[023] 0 ftape-ctl.c (ftape_enable_R7ec0d5d4) - ftape_activate_drive(ftape,
&ftape->drive_type) failed: -19.
[024] 0 zftape-ctl.c (_zft_open) - ftape_enable_R7ec0d5d4(sel) failed: -19.
[025] 0 zftape-init.c (zft_open) - _zft_open failed.
-----------
- Steve
