Dear Alan,
make modules_install
were the missing magic words :-). Stupid me.
dmesg: the philips hub is directly connected to the PC and the Sandisk device
is attached to one of its ports. Then I did reboot the linux box.
kernel reboot with hub and sandisk attached to 5:
Linux version 2.6.11.4-21.7-smp ([EMAIL PROTECTED]) (gcc version 3.3.5 20050117
(prerelease) (SUSE Linux)) #6 SMP Tue Jul 5 19:26:26 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 261936
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 32560 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v002 ACPIAM ) @ 0x000f9e30
ACPI: XSDT (v001 A M I OEMXSDT 0x10000426 MSFT 0x00000097) @ 0x3ff30100
ACPI: FADT (v003 A M I OEMFACP 0x10000426 MSFT 0x00000097) @ 0x3ff30290
ACPI: MADT (v001 A M I OEMAPIC 0x10000426 MSFT 0x00000097) @ 0x3ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x10000426 MSFT 0x00000097) @ 0x3ff40040
ACPI: DSDT (v001 P4CED P4CED106 0x00000106 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
Built 1 zonelists
Kernel command line: root=/dev/sdb1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3207.387 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029488k/1047744k available (2114k kernel code, 17472k reserved, 704k
data, 248k init, 130240k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 6356.99 BogoMIPS (lpj=3178496)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
0000041d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000041d
00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000041d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 3916k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
CPU0: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 03
per-CPU timeslice cutoff: 2925.86 usecs.
task migration cache decay timeout: 3 msecs.
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 6406.14 BogoMIPS (lpj=3203072)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
0000041d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000041d
00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000041d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 03
Total of 2 processors activated (12763.13 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to [EMAIL PROTECTED] cc [EMAIL PROTECTED])
pnp: 00:0a: ioport range 0x680-0x6ff has been reserved
pnp: 00:0a: ioport range 0x290-0x297 has been reserved
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1120594078.783:0): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
Starting balanced_irq
PM: Checking swsusp image.
PM: Resume from disk failed.
ACPI wakeup devices:
P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K PS2M ILAN
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 248k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
SCSI subsystem initialized
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
logips2pp: Detected unknown logitech mouse model 56
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
hda: _NEC DVD_RW ND-3520AW, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ACPI: PCI interrupt 0000:03:0a.0[A] -> GSI 22 (level, low) -> IRQ 177
ahc_pci:3:10:0: Host Adapter Bios disabled. Using default SCSI device
parameters
ACPI: PCI interrupt 0000:03:0d.0[A] -> GSI 21 (level, low) -> IRQ 185
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
Vendor: IBM Model: DDYS-T18350N Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB)
SCSI device sda: drive cache: write back
sda:
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:A:1): 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Vendor: MAXTOR Model: ATLAS10K5_73WLS Rev: JNZH
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled. Depth 32
SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:A:3): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
Vendor: SONY Model: SDT-10000 Rev: 0110
Type: Sequential-Access ANSI SCSI revision: 02
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2902/04/10/15/20C/30C SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
ReiserFS: sdb1: using ordered data mode
reiserfs: using flush barriers
ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb1: checking transaction log (sdb1)
reiserfs: disabling flush barriers on sdb1
ReiserFS: sdb1: Using r5 hash to sort names
Adding 3550356k swap on /dev/sdb2. Priority:42 extents:1
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
cdrom: open failed.
subfs 0.9
Linux agpgart interface v0.100 (c) Dave Jones
usbcore: registered new driver usbfs
usbcore: registered new driver hub
load_module: err 0xffffffef (dont worry)
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.0: UHCI Host Controller
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 193, io base 0xef00
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: detected 2 ports
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.11.4-21.7-smp uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.1: UHCI Host Controller
hub 1-0:1.0: state 5 ports 2 chg 0006 evt 0007
hub 1-0:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 201, io base 0xef20
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: detected 2 ports
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.11.4-21.7-smp uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.2: UHCI Host Controller
hub 2-0:1.0: state 5 ports 2 chg 0006 evt 0007
uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 169, io base 0xef40
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: detected 2 ports
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.11.4-21.7-smp uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.3: UHCI Host Controller
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 193, io base 0xef80
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: detected 2 ports
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.11.4-21.7-smp uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 209
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc
ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: capability 0001 at 68
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 209, pci mem 0xfebffc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.11.4-21.7-smp ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: ganged power switching
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: Single TT
hub 5-0:1.0: TT requires at most 8 FS bit times
hub 5-0:1.0: power on to power good time: 20ms
hub 5-0:1.0: local power source is good
hub 5-0:1.0: enabling power on all ports
Intel(R) PRO/1000 Network Driver - version 5.6.10.1-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
uhci_hcd 0000:00:1d.1: port 1 portsc 008a,00
uhci_hcd 0000:00:1d.1: port 2 portsc 0082,00
hub 2-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
load_module: err 0xffffffef (dont worry)
load_module: err 0xffffffef (dont worry)
load_module: err 0xffffffef (dont worry)
agpgart: Detected an Intel i875 Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 64M @ 0xf8000000
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:01.0 to 64
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0006 evt 0007
hub 3-0:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 3-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
hub 4-0:1.0: state 5 ports 2 chg 0006 evt 0007
hub 4-0:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 4-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
hub 5-0:1.0: state 5 ports 8 chg 01fe evt 01ff
hub 5-0:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 5-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
ieee1394: Initialized config rom entry `ip1394'
hub 5-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 3 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE
CONNECT
usb 5-3: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 3 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE
CONNECT
usb 5-3: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 5-3: hotplug
usb 5-3: adding 5-3:1.0 (config #1, interface 0)
usb 5-3:1.0: hotplug
hub 5-3:1.0: usb_probe_interface
hub 5-3:1.0: usb_probe_interface - got id
hub 5-3:1.0: USB hub found
hub 5-3:1.0: 4 ports detected
hub 5-3:1.0: standalone hub
hub 5-3:1.0: individual port power switching
hub 5-3:1.0: individual port over-current protection
hub 5-3:1.0: TT per port
hub 5-3:1.0: TT requires at most 8 FS bit times
hub 5-3:1.0: Port indicators are supported
hub 5-3:1.0: power on to power good time: 100ms
hub 5-3:1.0: local power source is good
hub 5-3:1.0: enabling power on all ports
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.5 to 64
usb 5-3: link qh256-0001/f6b84100 start 255 [7/0 us]
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE
CONNECT
usb 5-4: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE
CONNECT
usb 5-4: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 5-4: hotplug
usb 5-4: adding 5-4:1.0 (config #1, interface 0)
usb 5-4:1.0: hotplug
hub 5-4:1.0: usb_probe_interface
hub 5-4:1.0: usb_probe_interface - got id
hub 5-4:1.0: USB hub found
hub 5-4:1.0: 7 ports detected
hub 5-4:1.0: compound device; port removable status: FFFFFFF
hub 5-4:1.0: no power switching (usb 1.0)
hub 5-4:1.0: no over-current protection
hub 5-4:1.0: Single TT
hub 5-4:1.0: TT requires at most 16 FS bit times
hub 5-4:1.0: power on to power good time: 0ms
hub 5-4:1.0: local power source is good
usb 5-4: link qh256-0001/f6b84200 start 255 [7/0 us]
hub 5-0:1.0: port 5, status 0100, change 0000, 12 Mb/s
hub 5-0:1.0: port 6, status 0100, change 0000, 12 Mb/s
hub 5-0:1.0: port 7, status 0100, change 0000, 12 Mb/s
hub 5-0:1.0: port 8, status 0100, change 0000, 12 Mb/s
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.1: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
ALSA sound/pci/ac97/ac97_codec.c:1979: AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 50088 usecs
intel8x0: clocking to 48000
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 5-0:1.0: state 5 ports 8 chg 0000 evt 0000
hub 5-3:1.0: state 5 ports 4 chg 001e evt 0002
ohci1394: $Rev: 1250 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI interrupt 0000:03:03.0[A] -> GSI 20 (level, low) -> IRQ 225
hub 5-3:1.0: port 1, status 0101, change 0001, 12 Mb/s
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[225] MMIO=[feaff800-feafffff]
Max Packet=[2048]
hub 5-3:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 5-3.1: new high speed USB device using ehci_hcd and address 4
usb 5-3.1: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 5-3.1: hotplug
usb 5-3.1: adding 5-3.1:1.0 (config #1, interface 0)
usb 5-3.1:1.0: hotplug
hub 5-3.1:1.0: usb_probe_interface
hub 5-3.1:1.0: usb_probe_interface - got id
hub 5-3.1:1.0: USB hub found
hub 5-3.1:1.0: 4 ports detected
hub 5-3.1:1.0: standalone hub
hub 5-3.1:1.0: individual port power switching
hub 5-3.1:1.0: individual port over-current protection
hub 5-3.1:1.0: TT per port
hub 5-3.1:1.0: TT requires at most 8 FS bit times
hub 5-3.1:1.0: Port indicators are supported
hub 5-3.1:1.0: power on to power good time: 100ms
hub 5-3.1:1.0: local power source is good
hub 5-3.1:1.0: enabling power on all ports
usb 5-3.1: link qh256-0001/f6b84300 start 255 [7/0 us]
hub 5-3:1.0: port 2, status 0100, change 0000, 12 Mb/s
hub 5-3:1.0: port 3, status 0100, change 0000, 12 Mb/s
hub 5-3:1.0: port 4, status 0100, change 0000, 12 Mb/s
hub 5-4:1.0: state 5 ports 7 chg 00fe evt 00ff
hub 5-4:1.0: port 1, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 2, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 3, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 4, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 5, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 6, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 7, status 0000, change 0000, 12 Mb/s
hub 5-3:1.0: state 5 ports 4 chg 0000 evt 0002
hub 5-3.1:1.0: state 5 ports 4 chg 001e evt 001f
hub 5-3.1:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 5-3.1:1.0: port 2, status 0100, change 0000, 12 Mb/s
hub 5-3.1:1.0: port 3, status 0100, change 0000, 12 Mb/s
hub 5-3.1:1.0: port 4, status 0100, change 0000, 12 Mb/s
uhci_hcd 0000:00:1d.0: suspend_hc
uhci_hcd 0000:00:1d.1: suspend_hc
uhci_hcd 0000:00:1d.2: suspend_hc
uhci_hcd 0000:00:1d.3: suspend_hc
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800007765e1]
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi0, channel 0, id 1, lun 0, type 0
Attached scsi generic sg2 at scsi0, channel 0, id 3, lun 0, type 1
cdrom: open failed.
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
st: Version 20041025, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi0, channel 0, id 3, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
NET: Registered protocol family 17
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon[6708]: VMMON CPUID: Unrecognized CPU
/dev/vmmon[6708]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[6708]: Module vmmon: initialized
/dev/vmnet: open called by PID 6737 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
load_module: err 0xffffffef (dont worry)
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
NET: Registered protocol family 10
Disabled Privacy Extensions on device c037f760(lo)
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device f68f4400(sit0)
ACPI: Power Button (FF) [PWRF]
Non-volatile memory driver v1.2
powernow: This module only works with AMD K7 CPUs
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
eth0: no IPv6 routers present
remarks:
- if I detach the sandisk and reattach it, no log is generated.
- if I detach the hub and reattach it, I get the following log:
hub 5-0:1.0: state 5 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 5-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
usb 5-4: USB disconnect, address 3
usb 5-4: usb_disable_device nuking all URBs
usb 5-4: unlink qh256-0001/f6b84200 start 255 [7/0 us]
ehci_hcd 0000:00:1d.7: shutdown urb f6d0a780 pipe 40408380 ep1in-intr
usb 5-4: unregistering interface 5-4:1.0
usb 5-4:1.0: hotplug
usb 5-4: unregistering device
usb 5-4: hotplug
hub 5-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
hub 5-0:1.0: state 5 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE
CONNECT
usb 5-4: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE
CONNECT
usb 5-4: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 5-4: hotplug
usb 5-4: adding 5-4:1.0 (config #1, interface 0)
usb 5-4:1.0: hotplug
hub 5-4:1.0: usb_probe_interface
hub 5-4:1.0: usb_probe_interface - got id
hub 5-4:1.0: USB hub found
hub 5-4:1.0: 7 ports detected
hub 5-4:1.0: compound device; port removable status: FFFFFFF
hub 5-4:1.0: no power switching (usb 1.0)
hub 5-4:1.0: no over-current protection
hub 5-4:1.0: Single TT
hub 5-4:1.0: TT requires at most 16 FS bit times
hub 5-4:1.0: power on to power good time: 0ms
hub 5-4:1.0: local power source is good
usb 5-4: link qh256-0001/f6b84200 start 255 [7/0 us]
hub 5-4:1.0: state 5 ports 7 chg 00fe evt 00ff
hub 5-4:1.0: port 1, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 2, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 3, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 4, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 5, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 6, status 0000, change 0000, 12 Mb/s
hub 5-4:1.0: port 7, status 0000, change 0000, 12 Mb/s
-if I connect the sandisk to the end of two active usb cables, I get the
following messages:
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: new high speed USB device using
ehci_hcd and address 6
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: default language 0x0409
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: new device strings: Mfr=2,
Product=3, SerialNumber=4
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: Product: ImageMate CF
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: Manufacturer: SanDisk
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: SerialNumber: 0100772234
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: hotplug
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1: adding 5-3.1.1:1.0 (config #1,
interface 0)
Jul 5 21:03:10 loonquawl kernel: usb 5-3.1.1:1.0: hotplug
Jul 5 21:03:10 loonquawl kernel: usbserial_generic 5-3.1.1:1.0:
usb_probe_interface
Jul 5 21:03:10 loonquawl kernel: usbserial_generic 5-3.1.1:1.0:
usb_probe_interface - got id
Jul 5 21:03:11 loonquawl kernel: Initializing USB Mass Storage driver...
Jul 5 21:03:11 loonquawl kernel: usb-storage 5-3.1.1:1.0: usb_probe_interface
Jul 5 21:03:11 loonquawl kernel: usb-storage 5-3.1.1:1.0: usb_probe_interface
- got id
Jul 5 21:03:11 loonquawl kernel: usb-storage: USB Mass Storage device
detected
Jul 5 21:03:11 loonquawl kernel: usb-storage: -- associate_dev
Jul 5 21:03:11 loonquawl kernel: usb-storage: Vendor: 0x0781, Product:
0x9191, Revision: 0x0032
Jul 5 21:03:11 loonquawl kernel: usb-storage: Interface Subclass: 0x06,
Protocol: 0x50
Jul 5 21:03:11 loonquawl kernel: usb-storage: Transport: Bulk
....
regards
Dani
-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
