Re: stroke length

[David Costello]

I'm running a Wolf EMS computer, VL Turbo pump and a high flowed T3   with the new stroker bottom end I will be getting a surge tank, bigger injectors and possibly multiple fuel pumps and run some big boost   Dave ----- Original Message ----- From: Zac Campbell To: [EMAIL PROTECTED] Sent: Tuesday, January 15, 2002 1:27 PM Subject: Re: stroke length a turbo engine doesn't have to rev hard to work. he could undersize the turbo and have it boost very early in the rev range making bulk low rpm torque but the compromise there would be the turbo running out of efficiency in the higher rev ranges, where the stroker l24 is (said to be) limited anyway. if the turbo was sized right and could make big psi at very low revs and be a bit like a v8 in power delivery. I'd be tempted to do this, the more I think about it the better it sounds!   david what fuel system are you going to use, carby or efi?     ----- Original Message ----- From: David Costello To: [EMAIL PROTECTED] Sent: Tuesday, January 15, 2002 1:35 PM Subject: Re: stroke length why's that heath? more cubes plus boost is a good thing long as you build it so it revs   Dave ----- Original Message ----- From: Cleary Signs To: [EMAIL PROTECTED] Sent: Tuesday, January 15, 2002 9:53 AM Subject: Re: stroke length Dave, my idea would be to use a series2 bluebird crank, an not stroke it, as you arre turbo'ed it, but courses for horses   Heath ----- Original Message ----- From: andrew smith To: [EMAIL PROTECTED] Sent: Tuesday, January 15, 2002 9:41 AM Subject: Re: stroke length David, I would forget about using the z24 rods.The L20 rods would mean that with L20 piston that the pin height would be about 5mm to much so you need to find some pistons with 5mm less pin height.The z22e late model pistons list as a 32.1 pin height when compared to the L20 as 38.1 which is 6mm and you could deck the block if the comp was to low.These pistons are 87mm bore but unsure on the dish.Others on the list may have some better ideas. Andrew Smith David Costello wrote: I've got my Z24 crank, L20B rods, Z20 block, and was going to get custom pistons made to finish the combo but I've just had a thought...won't this combo only make it like a 2.2 or 2.3L not the full 2.4 .. since I'm getting custom pistons made anyway, can I use Z24 rods and just get the pistons made to suit? or will the piston be too weak due to the pin being so close to the piston crown (considering I plan running BIG boost) Dave --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ ---------------------------------------------------------------------