I always oil mine every time before I use it, too much oil won't kill it. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of maldat Sent: Wednesday, 4 December 2002 9:01 PM To: [EMAIL PROTECTED] Subject: Re: Rear Wheel bearing
They do seam to work longer if you put oil thru them from time to time.. Most people dont, Malcolm ----- Original Message ----- From: "Richard Clough" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Wednesday, December 04, 2002 9:39 PM Subject: Re: Rear Wheel bearing > My "SupaCheap Auto" rattle gun wont even undo tight wheel nuts. Forget them > for anything like flywheels or rear axles. They are only good for wood > workers. > > You need to spend at least $250 to get a Cincinnatti or SP rattle gun if you > are looking at 200 plus ft lbs. @ 100psi. > ----- Original Message ----- > From: "maldat" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Saturday, 30 November 2002 14:40 PM > Subject: Re: Rear Wheel bearing > > > > $93usd for a hammer gun is too much.(unless its a usa made one) > > > > The made in china ones here cost $100nz (about $50usd)they work well > > everyday for a year then buy a new one..(thats in a wreckers yard using > all > > day everyday) > > But if youre in ozzie the NZ$ and the ozzie$ are much the same these days > > Malcolm > > ----- Original Message ----- > > From: "Geordie Smith" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Saturday, November 30, 2002 4:09 PM > > Subject: RE: Rear Wheel bearing > > > > > > > I am a big bloke, and I had to do the flywheel bolts up on my SR20 to > 140 > > > ft/lb. It was hard yakka for a big boofy bloke like me. I had trouble, > not > > > only that, but also with busting 3x sockets. > > > 230-250 ft/lb off a rattle gun could be applied by a 5 year old using > two > > > hands. > > > I bought my rattle gun off Ebay for $93 It pulls 250ft/lb and has done > > > everything I've chucked at it so far without busting a single socket. > Just > > > pull the trigger and wait until the nut comes off. Can't get much easier > > > than that. > > > > > > Free Shameless Plug here... > > > If anyone wants a rattle gun, the guy I bought mine off was > > > [EMAIL PROTECTED] a guy name Andreas Muller. This guy is > cool, > > > and the rattle gun I bought was $60 cheaper than anything in the shops. > > > This guy also has some other cool tools as well!!! :) > > > > > > > > > > > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > > [mailto:[EMAIL PROTECTED]]On Behalf Of Terry Rudd > > > Sent: Saturday, 30 November 2002 2:01 PM > > > To: [EMAIL PROTECTED] > > > Subject: RE: Rear Wheel bearing > > > > > > > > > I'd have to think for while on how you can safely stop the axle turning > if > > > you have to jack the car up - a decent wheel brace like 70's Falcons > have > > > may be able to fit in the studs and have enough length to contact the > > > floor - but you've also got to keep it in place somehow - two round > > surfaces > > > together, may not be ideal. Oh and don't pull the handbrake on like a > mate > > > of mine tried many years ago, it will go bang and rip the shoes "clean > > off" > > > (in my Clint Eastwood accent) the backing plate. 240 ft/lbs is a lot of > > > torque and on that, I've never seen a rattle gun in the average car > garage > > > that goes near that, I spose there are truck ones though. > > > > > > Another problem with a rattle gun? Does Newtons law about relativity > apply > > > to them, cause if it does then you've got another problem. I don't know > > too > > > many people who can direct pull 240 ft/lbs, that's why a 3 ft bar > > (assuming > > > 1 ft ratchet) you'd have at least 2 ft leverage or is it the full 3 ft, > > > probably something in between, (my engineering is a bit poor in this > area) > > > so you're only pulling somewhere between 80 ft/lbs up to 120 ft/lb at > most > > > and most ppl can manage that, mind you flat on your back under a lowered > > > 1600 on the muffler side - yeah, it wasn't meant to be easy. I'd assume > > 1hr > > > labour per side would be what it costs at the garage - I think you'd get > > the > > > bearings off the shaft and new ones pressed on in an hour with the right > > > tools (and a bit of now how), and allow $15 per side for a new nut > > > (43262-21000). > > > > > > regards > > > Terry > > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > > [mailto:[EMAIL PROTECTED]]On Behalf Of Richard Webb > > > Sent: Sunday, 1 December 2002 7:49 AM > > > To: [EMAIL PROTECTED] > > > Subject: Re: Rear Wheel bearing > > > > > > > > > Thanks for the help terry, > > > > > > I've taken both the dive shafts from the hubs. and the noise is > definatly > > > coming from the suspension arm... Its really annoying I've got a torque > > > wrench (bout foot long) and it kept clicking so I turned the torque up > as > > > high as possible.... then I bent the hammer which was stoping the studs > > > turning :).... So do you think its best to do it with the wheel on? I > dont > > > think Im going to have much luck with it off. Its just theres not much > > room > > > as its lowered and the torque wrench or bar will hit the muffler. I can > > take > > > it to my friends house with a pit, which might make it easier to get > force > > > on the wheel. > > > > > > Least I'm pushing the car onto the ground and not lifting it up. Maybe > > this > > > is a job for the mechanics after all.... How much would they charge?? > > (lol, > > > sure I do give up easy) > > > > > > Anyway thanks for the help > > > > > > Richard > > > ----- Original Message ----- > > > From: "Terry Rudd" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Friday, November 29, 2002 5:29 PM > > > Subject: RE: Rear Wheel bearing > > > > > > > > > > Richard, > > > > > > > > I crook wheel bearing will vary the noise (pitch) depending wether > under > > > > load or not - so if you do a tyre warm up weave you'll have the noise > on > > > the > > > > side under load - bugger when they're both shot. > > > > > > > > To get that supa dupa tight nut off (240 ft/lbs) in a home garage you > > have > > > > to have the car on the ground. Get a good quality ratchet and socket > > (27mm > > > > or 1 1/16") and a 3 foot piece of water pipe or breaker bar. You can > > > nearly > > > > lift the car off the ground (drivers side) gettin' that nut to budge > and > > > the > > > > reverse on the pass side. To remove the axle you are best to use a > slide > > > > hammer i.e. plate or decent piece of angle iron drilled to match a > > couple > > > of > > > > wheel studs and cabamm. A little heat around the hub can sometimes be > > > > required to free up a stubborn axle. Make sure you note the stamping > (A, > > B > > > > or C) on the spacer between the axle so you re-fit it back into the > same > > > > side. The rest of it is covered pretty well in the manual. > > > > > > > > A shot carrier bearing will normally whine all the time i.e. pitch > > changes > > > > with road speed and not load unless it's the pinion bearing. Likewise > > for > > > > unis but the noise from them is very different, more a rumble than a > > > whining > > > > noise and the only way to check unis is by securing one side and > rocking > > > the > > > > other side and looking for play in the end caps of the joint. You > can't > > > get > > > > much of an idea from just jacking the wheels off the ground and > running > > a > > > > 1600 IRS as a uni rearend is that noisy in brand new condition. > > > > > > > > Good luck with it, > > > > > > > > regards > > > > Terry > > > > > > > > -----Original Message----- > > > > From: [EMAIL PROTECTED] > > > > [mailto:[EMAIL PROTECTED]]On Behalf Of Richard Webb > > > > Sent: Sunday, 1 December 2002 7:05 AM > > > > To: [EMAIL PROTECTED] > > > > Subject: Re: Rear Wheel bearing > > > > > > > > > > > > Nevermind, Gregorys put it in Rear suspension section... I woulda > > thaught > > > it > > > > was driveline. Now I just gotta work out a way of getting the nut that > > > holds > > > > the bearing together off... its very tight. > > > > ----- Original Message ----- > > > > From: "Richard Webb" <[EMAIL PROTECTED]> > > > > To: <[EMAIL PROTECTED]> > > > > Sent: Saturday, November 30, 2002 9:59 AM > > > > Subject: Rear Wheel bearing > > > > > > > > > > > > > I've recently had a kinda bearing noise (thats getting louder and > > > louder) > > > > > coming from the rear of my car. Can someone tell me which bearing > its > > > most > > > > > likely to be? I can turn the wheel but the noise seems to come out > of > > > > > somewhere on the left side. > > > > > > > > > > I've got the rear brakes off and Im trying to get to the bearing > which > > > is > > > > > inside the swing arm. Im not 100% sure its not one of the bearings > in > > > the > > > > > diff. > > > > > > > > > > is there any way of doing this without bleeding the brakes? :) I > hate > > > > doing > > > > > that > > > > > > > > > > Richard > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
