I reckon the Z18 dizzy might be a magnetic pickup. Either way, I think cam needs to setup the ECU to suit the Z18 dizzy. I would be talking to Microtech about that. If the settings for a FJ20 CAS and a Z18 dizzy are the same, then why would someone have fitted the FJ20 CAS in the first place? Cam are you running with direct fire ignition aswell?
zac ----- Original Message ----- From: "David Andrews" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Sunday, February 23, 2003 6:02 PM Subject: Re: no ignition/injector pule :( > Sweet, you should be fine then I'd reckon. Just look for the spot where > you can tell it its a hall-effect and vroooom! (hopefully). > > Dave > > >>>>>>>>>>>>>>>>>> Original Message <<<<<<<<<<<<<<<<<< > > On 2/23/03, 5:20:37 PM, "Cameron Stean" <[EMAIL PROTECTED]> wrote > regarding Re: no ignition/injector pule :(: > > > > yeah I do have the handset.. > > > Im going to do what you said, retard the dizzy tommorrow and see if it > picks > > up.. > > > and the z18 dizzy has 5 cables coming out from going off wiring diagrams > I > > have they seem to be (black/white)12v ign, (red)signal 1, and > (blue)signal > > 2.. and a 2 wire going into a lug for the knock sensor. > > > > > > > >From: "Zac Campbell" <[EMAIL PROTECTED]> > > >Reply-To: [EMAIL PROTECTED] > > >To: <[EMAIL PROTECTED]> > > >Subject: Re: no ignition/injector pule :( > > >Date: Sun, 23 Feb 2003 16:20:32 +1030 > > > > > >I said that because Cam doesn't have the FJ20 CAS that was previously > > >used.. > > >he has the stock Z18 dizzy which probably gives out a different signal.. > > >you retard the dizzy so the ECU picks up the trigger before it needs to > > >fire, then it can delay the signal and fire right on time! > > >Cam do you have the hand controller for the microtech? > > >zac > > > > > >----- Original Message ----- > > >From: "David Andrews" <[EMAIL PROTECTED]> > > >To: <[EMAIL PROTECTED]> > > >Sent: Sunday, February 23, 2003 1:21 PM > > >Subject: Re: no ignition/injector pule :( > > > > > > > > > > The FJ20 CAS is used for just that, all it does is tell the ecu where > > >the > > > > crank is at. Now my autronic has several options for this, hall-effect > > > > sensor distributor, OEM CAS, or optical CAS. I believe you can tell if > > > > the Z18ET is a hall-effect type by seeing if it has three wires come out > > > > of it. In either case, as Zac said, you'll need to get into the ecu and > > > > tell it its using a hall-effect dizzy. > > > > > > > > I don't know about the microtech (georgie?), but the autronic manual > > >says > > > > that you should manually rotate the dizzy 60 degrees BTDC, buggered if i > > > > know why. Consult ze manuel. > > > > Cheers, > > > > > > > > Dave > > > > > > > > >>>>>>>>>>>>>>>>>> Original Message <<<<<<<<<<<<<<<<<< > > > > > > > > On 2/23/03, 1:32:45 AM, "Zac Campbell" <[EMAIL PROTECTED]> wrote > > >regarding > > > > Re: no ignition/injector pule :(: > > > > > > > > > > > > > yeha you will need to configure the microtech to suit whatever crank > > > > angle > > > > > sensor you are using with your Z18ET. > > > > > > > > > ----- Original Message ----- > > > > > From: "Cameron Stean" <[EMAIL PROTECTED]> > > > > > To: <[EMAIL PROTECTED]> > > > > > Sent: Saturday, February 22, 2003 8:34 PM > > > > > Subject: no ignition/injector pule :( > > > > > > > > > > > > > > > > > I have struck another problem with the project :/ > > > > > everything is wired up, no errors in the ecu error log, but when I go > > >to > > > > > start... no ignition pulse/injector pulse... I've checked all the > > >wires > > > > but > > > > > hav'nt found "the" problem, I'm running a microtech mtx-8 with haltech > > > > hec > > > > > twin ignitor and 2 twin spark coil packs... the previous owner was > > > > running a > > > > > FJ20 C.A.S and I'm running the sensor in the stock Z18 distributor.. > > > > would > > > > > the settings in the ecu conflict? > > > > > > > > > anybody had this problem? any ideas what it could be? > > > > > > > > > dont really want to take it to mazfix to get fixed if i can do it > > >myself > > > > and > > > > > save alot of money... > > > > > > > > > thanks for any info > > > > > > > > > Cameron > > > > > > > > > > > > > _________________________________________________________________ > > > > > MSN Instant Messenger now available on Australian mobile phones. Go to > > > > > http://ninemsn.com.au/mobilecentral/hotmail_messenger.asp > > > > > > > > > > > > > > > > > > > > > > > > > > > _________________________________________________________________ > > Hotmail now available on Australian mobile phones. Go to > > http://ninemsn.com.au/mobilecentral/hotmail_mobile.asp > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[EMAIL PROTECTED]/ ---------------------------------------------------------------------
