If we assume that these panels are designed to run off full-wave rectified 
220V, perhaps here in the U.S. a Villard voltage doubler 
<https://www.intechopen.com/books/advanced-electronic-circuits-principles-architectures-and-applications-on-emerging-technologies/high-voltage-energy-harvesters>
 
would work? OTH, if you want to be able to dim/fade these panels, you would 
probably want a DC voltage. It seems like there would be no point PWMing at 
a few kHz on top of a 50/60Hz wave.

On Thursday, August 27, 2020 at 11:11:52 AM UTC-4, gregebert wrote:
>
> Disclaimer: Operating off the mains without isolation requires a lot of 
> extra care and attention to safety. I've done several designs this way 
> with  no problem. When in doubt, ask someone on this forum.
>
> A voltage doubler off the mains will work nicely; I did that in my first 
> nixie clock 10 years ago and it's still working fine. You have to be 
> careful to limit the inrush current and add surge-protection (varistor AND 
> fuse) to protect the electrolytic caps. That will get you 340V, so there 
> will be wasted energy (heat).
>
> If you want 260 VDC from the US mains (120V), you can also use a "boost" 
> transformer to add about 65VAC to the 120VAC line. I've used that technique 
> with smaller transformers to get +200VDC and +215VDC on different projects.
>
>
>
> On Thursday, August 27, 2020 at 6:30:08 AM UTC-7 Paul Andrews wrote:
>
>> Power requirements are quite extreme, at least compared with what we 
>> might all be used to. When I tested my first board I drove it at 240V and 
>> it drew around 230mA with all tubes lit. So for my four board clock I 
>> needed to provide around 1A at 240V. My boards have 27 tubes, so it takes 
>> around 9mA per tube. You can multiply it out.
>>
>> The obvious route in the UK, as Martin has said, is to use a mains driven 
>> power supply with a full wave rectifier. In the U.S. you would have to use 
>> a step-up transformer to get this. I didn't want my clock tethered to a 
>> step-up transformer - I wanted it to have everything it needed in whatever 
>> housing I came up with and I didn't want a heavy transformer in there, so I 
>> went with a stack of five of these power supplies 
>> <https://www.trcelectronics.com/View/Mean-Well/LPV-60-48.shtml> wired in 
>> series, giving me exactly 240V DC.
>>
>> If you have access to the trigger pin of the tubes, you can just keep it 
>> at the anode voltage and then you can drive the tubes like regular nixies - 
>> pull the cathode to the ground and it lights up. Let it float and it goes 
>> out. Obviously you need a resistor between the trigger pin and the HV. My 
>> boards already have this.
>>
>> On Thursday, August 27, 2020 at 8:55:44 AM UTC-4, M1 wrote:
>>
>>> Richard,
>>>
>>>  
>>>
>>> Sorry, I just ordered them.
>>>
>>> “Estimated delivery *Thursday, Oct 1, 2020* *- Thursday, Oct 29, 2020”*
>>>
>>>  
>>>
>>> I’m pretty sure you already know what I am going to make with them.
>>>
>>> Now, I am thinking of ordering more.  😊
>>>
>>>  
>>>
>>> I see a few of us have got them already.   What power supply are you 
>>> guys using?   I’ll need to drive 8 of them.
>>>
>>>  
>>>
>>> Michail Wilson
>>>
>>> 206-920-6312
>>>
>>>  
>>>
>>> *From:* [email protected] <[email protected]> *On 
>>> Behalf Of *Richard Scales
>>> *Sent:* Monday, August 24, 2020 8:44 PM
>>> *To:* neonixie-l <[email protected]>
>>> *Subject:* Re: [neonixie-l] Re: 7 Segment Nix
>>>
>>>  
>>>
>>> Michail, I would be interested to find out how you get on with these - 
>>> do you have them yet? 
>>>
>>> I have some here and they are quite different from the ones that Paul 
>>> has, there is a daughter board on the rear of the unit which actually 
>>> appears to do very little, the board has a lot of tracks for components 
>>> that are not fitted.
>>> Apart from that, there are three connections to each IN-28, one is 
>>> common to all tubes, one is common to all tubes but fed via a large 
>>> resistor and the third is common to each 'segment' and these are the ones 
>>> which go to the daughter board and then off to the edge of the main board.
>>> - Richard
>>>
>>>  
>>>
>>> On Monday, 24 August 2020 at 18:38:32 UTC+1 M1 wrote:
>>>
>>> 8 @ $30
>>>
>>>  
>>>
>>> Michail Wilson
>>>
>>> 206-920-6312
>>>
>>>  
>>>
>>> *From:* [email protected] <[email protected]> *On 
>>> Behalf Of *Christian Elzey
>>> *Sent:* Monday, August 24, 2020 10:33 AM
>>> *To:* [email protected]
>>> *Subject:* Re: [neonixie-l] Re: 7 Segment Nix
>>>
>>>  
>>>
>>> How low was your low offer? Wondering if I could go lower...
>>>
>>>  
>>>
>>> On Mon, Aug 24, 2020, 1:32 PM Michail Wilson <[email protected]> wrote:
>>>
>>> Hello,
>>>
>>>  
>>>
>>> I decided to get several of these as well.
>>>
>>>  
>>>
>>> I made a LOW bid offer and it was accepted minutes later.
>>>
>>>  
>>>
>>> Michail Wilson
>>>
>>> 206-920-6312
>>>
>>>  
>>>
>>> *From:* [email protected] <[email protected]> *On 
>>> Behalf Of *Richard Scales
>>> *Sent:* Saturday, August 22, 2020 9:45 PM
>>> *To:* neonixie-l <[email protected]>
>>> *Subject:* [neonixie-l] Re: 7 Segment Nix
>>>
>>>  
>>>
>>> I also bagged a few of these on a low(ish) offer and they just arrived. 
>>> They were extremely well packaged - I think I'm OK for bubble wrap for 
>>> quite some time now.
>>> No idea how to drive/interface/connect/power, there is a smaller 
>>> daughter board on the back of the main PC. The 'segments' are clearly 
>>> arranged and I am guessing that there are 7 individually addressable 
>>> segments that are individually addressable.
>>> All pointers and suggestions gleefully received.
>>>
>>> I look forward to hearing what you make of them Chris.
>>>
>>> - Richard
>>>
>>>  
>>>
>>>  
>>>
>>> On Saturday, 22 August 2020 at 11:11:11 UTC+1 Dekatron42 wrote:
>>>
>>> This display was discussed here on the forum a few weeks ago: 
>>> https://groups.google.com/forum/#!topic/neonixie-l/bVoCKhPv7Dg the 
>>> tubes are IN-28 single dot nixies for large displays. These displays were 
>>> supposedly used in the Russian metro and other places. It also turned up in 
>>> the game Metro Exodus which I wrote about here: 
>>> https://groups.google.com/forum/#!searchin/neonixie-l/in-28%7Csort:date/neonixie-l/S4Evx0_z3ak/WE3e6tqSAAAJ
>>> .
>>>
>>>  
>>>
>>> There have been at least two large "clocks" with four of these displays 
>>> with a large metal front sold on ebay over the years, I asked the seller 
>>> about those and I was told that they didn't have the "clock" electronics so 
>>> you had to drive them yourself, perhaps they were slave units hooked up to 
>>> a master clock. The clock has been discussed here on the forum too (I 
>>> didn't read through that thread now): 
>>> https://groups.google.com/forum/#!searchin/neonixie-l/in-28|sort:date/neonixie-l/PC8pHxmTWSg/74pk9tloBwAJ,
>>>  
>>> maybe the thread shows if it contained the clock electronics or not.
>>>
>>>  
>>>
>>> /Martin
>>>
>>>
>>> On Thursday, 20 August 2020 16:17:38 UTC+2, martin martin wrote:
>>>
>>> Not my listing.  Looks interesting
>>>
>>>
>>> https://www.ebay.com/itm/PCB-with-23-pieces-IN-28-nixie-tubes-slightly-used-working/114333271792?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D225086%26meid%3D49761308ecd441a998590284c2ed34f5%26pid%3D100675%26rk%3D1%26rkt%3D15%26mehot%3Dnone%26sd%3D114333271792%26itm%3D114333271792%26pmt%3D0%26noa%3D1%26pg%3D2380057&_trksid=p2380057.c100675.m4236&_trkparms=pageci%3Ac5551501-e2ef-11ea-8536-74dbd180e220%7Cparentrq%3A0c3a9e6a1740a6881cb64927ffffee54%7Ciid%3A1
>>>   
>>>
>>> -- 
>>> You received this message because you are subscribed to the Google 
>>> Groups "neonixie-l" group.
>>> To unsubscribe from this group and stop receiving emails from it, send 
>>> an email to [email protected].
>>> To view this discussion on the web, visit 
>>> https://groups.google.com/d/msgid/neonixie-l/fde962cf-11d9-47ea-811c-e5757ccf5464n%40googlegroups.com
>>>  
>>> <https://groups.google.com/d/msgid/neonixie-l/fde962cf-11d9-47ea-811c-e5757ccf5464n%40googlegroups.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>>> -- 
>>> You received this message because you are subscribed to a topic in the 
>>> Google Groups "neonixie-l" group.
>>> To unsubscribe from this topic, visit 
>>> https://groups.google.com/d/topic/neonixie-l/cVHd2j26I10/unsubscribe.
>>> To unsubscribe from this group and all its topics, send an email to 
>>> [email protected].
>>> To view this discussion on the web, visit 
>>> https://groups.google.com/d/msgid/neonixie-l/MW2PR0102MB343543C3F25B96D78E67A03D82560%40MW2PR0102MB3435.prod.exchangelabs.com
>>>  
>>> <https://groups.google.com/d/msgid/neonixie-l/MW2PR0102MB343543C3F25B96D78E67A03D82560%40MW2PR0102MB3435.prod.exchangelabs.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>>> -- 
>>> You received this message because you are subscribed to the Google 
>>> Groups "neonixie-l" group.
>>> To unsubscribe from this group and stop receiving emails from it, send 
>>> an email to [email protected].
>>>
>>> To view this discussion on the web, visit 
>>> https://groups.google.com/d/msgid/neonixie-l/CADjEcqCZnymU3ZWHnuWrbHtzfZb7j1aVnMNYUPuLYOtA5xQJpw%40mail.gmail.com
>>>  
>>> <https://groups.google.com/d/msgid/neonixie-l/CADjEcqCZnymU3ZWHnuWrbHtzfZb7j1aVnMNYUPuLYOtA5xQJpw%40mail.gmail.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>>> -- 
>>> You received this message because you are subscribed to the Google 
>>> Groups "neonixie-l" group.
>>>
>> To unsubscribe from this group and stop receiving emails from it, send an 
>>> email to [email protected].
>>>
>>
>>> To view this discussion on the web, visit 
>>> https://groups.google.com/d/msgid/neonixie-l/68cde36c-dc59-498e-a385-63fd9663e32en%40googlegroups.com
>>>  
>>> <https://groups.google.com/d/msgid/neonixie-l/68cde36c-dc59-498e-a385-63fd9663e32en%40googlegroups.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>>

-- 
You received this message because you are subscribed to the Google Groups 
"neonixie-l" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To view this discussion on the web, visit 
https://groups.google.com/d/msgid/neonixie-l/bb88c6ea-0292-49ba-9745-cf24fc153a64o%40googlegroups.com.

Reply via email to